Internet-Draft draft-ietf-ipsecme-mib-iptfs-03 November 2021
Fedyk & Kinzie Expires 22 May 2022 [Page]
Workgroup:
Network Working Group
Internet-Draft:
draft-ietf-ipsecme-mib-iptfs-03
Published:
Intended Status:
Standards Track
Expires:
Authors:
D. Fedyk
LabN Consulting, L.L.C.
E. Kinzie
LabN Consulting, L.L.C.

Definitions of Managed Objects for IP Traffic Flow Security

Abstract

This document describes managed objects for the the management of IP Traffic Flow Security additions to IKEv2 and IPsec. This document provides a read only version of the objects defined in the YANG module for the same purpose.

Status of This Memo

This Internet-Draft is submitted in full conformance with the provisions of BCP 78 and BCP 79.

Internet-Drafts are working documents of the Internet Engineering Task Force (IETF). Note that other groups may also distribute working documents as Internet-Drafts. The list of current Internet-Drafts is at https://datatracker.ietf.org/drafts/current/.

Internet-Drafts are draft documents valid for a maximum of six months and may be updated, replaced, or obsoleted by other documents at any time. It is inappropriate to use Internet-Drafts as reference material or to cite them other than as "work in progress."

This Internet-Draft will expire on 22 May 2022.

▲

Table of Contents

1. Introduction

This document defines a Management Information Base (MIB) module for use with network management protocols in the Internet community. Traffic Flow Security (IP-TFS) extensions as defined in [I-D.ietf-ipsecme-iptfs]. IP-TFS provides enhancements to an IPsec tunnel Security Association to provide improved traffic confidentiality.

For a detailed overview of the documents that describe the current Internet-Standard Management Framework, please refer to section 7 of [RFC3410].

Managed objects are accessed via a virtual information store, termed the Management Information Base or MIB. MIB objects are generally accessed through the Simple Network Management Protocol (SNMP). Objects in the MIB are defined using the mechanisms defined in the Structure of Management Information (SMI). This memo specifies a MIB module that is compliant to the SMIv2, which is described in STD 58, [RFC2578], STD 58, [RFC2579] and STD 58, [RFC2580].

The objects defined here are the same as [I-D.ietf-ipsecme-yang-iptfs] with the exception that only operational data is supported. This module uses the YANG model as a reference point for managed objects. Note an IETF MIB model for IPsec was never standardized however the structures here could be adapted to existing MIB implementations.

2. Terminology & Concepts

The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT", "SHOULD", "SHOULD NOT", "RECOMMENDED", "NOT RECOMMENDED", "MAY", and "OPTIONAL" in this document are to be interpreted as described in [RFC2119] [RFC8174] when, and only when, they appear in all capitals, as shown here.

3. Overview

This document defines configuration and operational parameters of IP traffic flow security (IP-TFS). IP-TFS, defined in [I-D.ietf-ipsecme-iptfs], configures a security association for tunnel mode IPsec with characteristics that improve traffic confidentiality and reduce bandwidth efficiency loss.

This document is based on the concepts and management model defined in [I-D.ietf-ipsecme-yang-iptfs]. This documents assume familiarity with IP security concepts described in [RFC4301], IP-TFS as described in [I-D.ietf-ipsecme-iptfs] and the IP-TFS management model described in [I-D.ietf-ipsecme-yang-iptfs].

This document specifies an extensible operational model for IP-TFS. It reuses the management model defined in [I-D.ietf-ipsecme-yang-iptfs]. It allows SNMP systems to read configured and operational objects of IPTFS.

4. Management Objects

4.1. MIB Tree

The following is the MIB registration tree diagram for the IP-TFS extensions.

# IETF-IPTFS-MIB registration tree (generated by smidump 0.4.8)

--iptfsMIB(1.3.6.1.3.500)
  +--iptfsMIBObjects(1)
  |  +--iptfsGroup(1)
  |  |  +--iptfsConfigTable(1)
  |  |     +--iptfsConfigTableEntry(1) [iptfsConfigSaIndex]
  |  |        +-- --- Integer32     iptfsConfigSaIndex(1)
  |  |        +-- r-n TruthValue    congestionControl(2)
  |  |        +-- r-n TruthValue    usePathMtu(3)
  |  |        +-- r-n UnsignedShort outerPacketSize(4)
  |  |        +-- r-n Counter64     l2FixedRate(5)
  |  |        +-- r-n Counter64     l3FixedRate(6)
  |  |        +-- r-n TruthValue    dontFragment(7)
  |  |        +-- r-n NanoSeconds   maxAggregationTime(8)
  |  |        +-- r-n Unsigned32    windowSize(9)
  |  |        +-- r-n TruthValue    sendImmediately(10)
  |  |        +-- r-n NanoSeconds   lostPktTimerInt(11)
  |  +--ipsecStatsGroup(2)
  |  |  +--ipsecStatsTable(1)
  |  |     +--ipsecStatsTableEntry(1) [ipsecSaIndex]
  |  |        +-- --- Integer32 ipsecSaIndex(1)
  |  |        +-- r-n Counter64 txPackets(2)
  |  |        +-- r-n Counter64 txOctets(3)
  |  |        +-- r-n Counter64 txDropPackets(4)
  |  |        +-- r-n Counter64 rxPackets(5)
  |  |        +-- r-n Counter64 rxOctets(6)
  |  |        +-- r-n Counter64 rxDropPackets(7)
  |  +--iptfsInnerStatsGroup(3)
  |  |  +--iptfsInnerStatsTable(1)
  |  |     +--iptfsInnerStatsTableEntry(1) [iptfsInnerSaIndex]
  |  |        +-- --- Integer32 iptfsInnerSaIndex(1)
  |  |        +-- r-n Counter64 txInnerPackets(2)
  |  |        +-- r-n Counter64 txInnerOctets(3)
  |  |        +-- r-n Counter64 rxInnerPackets(4)
  |  |        +-- r-n Counter64 rxInnerOctets(5)
  |  |        +-- r-n Counter64 rxIncompleteInnerPackets(6)
  |  +--iptfsOuterStatsGroup(4)
  |     +--iptfsOuterStatsTable(1)
  |        +--iptfsOuterStatsTableEntry(1) [iptfsSaIndex]
  |           +-- --- Integer32 iptfsSaIndex(1)
  |           +-- r-n Counter64 txExtraPadPackets(2)
  |           +-- r-n Counter64 txExtraPadOctets(3)
  |           +-- r-n Counter64 txAllPadPackets(4)
  |           +-- r-n Counter64 txAllPadOctets(5)
  |           +-- r-n Counter64 rxExtraPadPackets(6)
  |           +-- r-n Counter64 rxExtraPadOctets(7)
  |           +-- r-n Counter64 rxAllPadPackets(8)
  |           +-- r-n Counter64 rxAllPadOctets(9)
  |           +-- r-n Counter64 rxErroredPackets(10)
  |           +-- r-n Counter64 rxMissedPackets(11)
  +--iptfsMIBConformance(2)
     +--iptfsMIBConformances(1)
     |  +--iptfsMIBCompliance(1)
     +--iptfsMIBGroups(2)
        +--iptfsMIBConfGroup(1)
        +--ipsecStatsConfGroup(2)
        +--iptfsInnerStatsConfGroup(3)
        +--iptfsOuterStatsConfGroup(4)

4.2. SNMP

The following is the MIB for IP-TFS. The Congestion control algorithm in [RFC5348] is refrenced in the MIB text.

-- *----------------------------------------------------------------
-- *
-- *----------------------------------------------------------------

IETF-IPTFS-MIB DEFINITIONS ::= BEGIN
   IMPORTS
        MODULE-IDENTITY, OBJECT-TYPE,
        Integer32, Unsigned32, Counter64, experimental
            FROM SNMPv2-SMI
        MODULE-COMPLIANCE, OBJECT-GROUP
            FROM SNMPv2-CONF
        TEXTUAL-CONVENTION,
        TruthValue
            FROM SNMPv2-TC;

   iptfsMIB MODULE-IDENTITY
        LAST-UPDATED "202111180000Z"
        ORGANIZATION "IETF IPsecme Working Group"
        CONTACT-INFO
                "
                   Author: Don Fedyk
                           <mailto:dfedyk@labn.net>

                   Author: Eric Kinzie
                           <mailto:ekinzie.labn.net>"


   DESCRIPTION
      "This module defines the configuration and operational
      state for managing the IP Traffic Flow Security
      functionality [RFC XXXX].  Copyright (c) 2021 IETF
      Trust and the persons identified as authors of the
      code. All rights reserved.

      Redistribution and use in source and binary forms,
      with or without modification, is permitted pursuant
      to, and subject to the license terms contained in,
      the Simplified BSD License set forth in Section 4.c
      of the IETF Trust's Legal Provisions Relating to IETF
      Documents (https://trustee.ietf.org/license-info).

      This version of this SNMP MIB module is part of RFC XXXX
      (https://tools.ietf.org/html/rfcXXXX); see the RFC
      itself for full legal notices."


    REVISION "202111180000Z"
    DESCRIPTION
            "Initial revision. Derived from the IPTFS Yang Model."
    ::= { experimental 500 }
--
-- Textual Conventions
--

UnsignedShort ::= TEXTUAL-CONVENTION
    DISPLAY-HINT "d"
    STATUS      current
    DESCRIPTION "xs:unsignedShort"
    SYNTAX      Unsigned32 (0 .. 65535)


NanoSeconds ::= TEXTUAL-CONVENTION
    DISPLAY-HINT "d"
    STATUS  current
    DESCRIPTION
      "Represents time unit value in nanoseconds."
    SYNTAX      Counter64


-- Objects, Notifications & Conformances

   iptfsMIBObjects     OBJECT IDENTIFIER
               ::= { iptfsMIB 1 }
   iptfsMIBConformance OBJECT IDENTIFIER
               ::= { iptfsMIB 2}

--
-- IPTFS MIB Object Groups
--
   iptfsGroup OBJECT IDENTIFIER
              ::= { iptfsMIBObjects 1 }

   ipsecStatsGroup OBJECT IDENTIFIER
              ::= { iptfsMIBObjects 2 }

   iptfsInnerStatsGroup OBJECT IDENTIFIER
              ::= { iptfsMIBObjects 3 }

   iptfsOuterStatsGroup OBJECT IDENTIFIER
              ::= { iptfsMIBObjects 4 }

   iptfsConfigTable OBJECT-TYPE
       SYNTAX     SEQUENCE OF IptfsConfigTableEntry
       MAX-ACCESS not-accessible
       STATUS     current
       DESCRIPTION
               "The table containing configuration information for
               IPTFS."
       ::= { iptfsGroup 1 }

   iptfsConfigTableEntry OBJECT-TYPE
       SYNTAX     IptfsConfigTableEntry
       MAX-ACCESS not-accessible
       STATUS     current
       DESCRIPTION
         "An entry (conceptual row) containing the information on
         a particular IPTFS SA."
       INDEX      { iptfsConfigSaIndex }
       ::= { iptfsConfigTable 1 }

  IptfsConfigTableEntry ::= SEQUENCE {
      iptfsConfigSaIndex         Integer32,

   -- identifier information
      congestionControl          TruthValue,
      usePathMtu                 TruthValue,
      outerPacketSize            UnsignedShort,
      l2FixedRate                Counter64,
      l3FixedRate                Counter64,
      dontFragment               TruthValue,
      maxAggregationTime         NanoSeconds,
      windowSize                 Unsigned32,
      sendImmediately            TruthValue,
      lostPktTimerInt            NanoSeconds
   }

   iptfsConfigSaIndex OBJECT-TYPE
       SYNTAX      Integer32 (1..16777215)
       MAX-ACCESS  not-accessible
       STATUS      current
       DESCRIPTION
         "A unique value, greater than zero, for each SA.
         It is recommended that values are assigned contiguously
         starting from 1.

         The value for each entry must remain constant at least
         from one re-initialization of entity's network management
         system to the next re-initialization."
       ::= { iptfsConfigTableEntry 1 }

    congestionControl OBJECT-TYPE
        SYNTAX      TruthValue
        MAX-ACCESS  read-only
        STATUS      current
        DESCRIPTION
          "When set to true, the default, this enables the
          congestion control on-the-wire exchange of data that is
          required by congestion control algorithms as defined by
          RFC 5348.  When set to false, IP-TFS sends fixed-sized
          packets over an IP-TFS tunnel at a constant rate."
        DEFVAL { false }
        ::= { iptfsConfigTableEntry 2 }

    usePathMtu OBJECT-TYPE
        SYNTAX      TruthValue
        MAX-ACCESS  read-only
        STATUS      current
        DESCRIPTION
          "Packet size is either auto-discovered or manually
          configured. If usePathMtu is true the system utilizes
          path-mtu to determine maximum IPTFS packet size.  If
          the packet size is explicitly configured then it will
          only be adjusted downward if use-path-mtu is set."
        ::= { iptfsConfigTableEntry 3 }

    outerPacketSize OBJECT-TYPE
        SYNTAX      UnsignedShort
        MAX-ACCESS  read-only
        STATUS      current
        DESCRIPTION
          "On Transmission, the size of the outer encapsulating
          tunnel packet (i.e., the IP packet containing the ESP
          payload)."
        ::= { iptfsConfigTableEntry 4 }

    l2FixedRate OBJECT-TYPE
        SYNTAX      Counter64
        MAX-ACCESS  read-only
        STATUS      current
        DESCRIPTION
          "TFS bit rate may be specified at layer 2 wire rate.  On
          transmission, target bandwidth/bit rate in bps for iptfs
          tunnel.  This rate is the nominal timing for the fixed
          size packet. If congestion control is enabled the rate
          may be adjusted down (or up if unset)."
        ::= { iptfsConfigTableEntry 5 }

    l3FixedRate OBJECT-TYPE
        SYNTAX      Counter64
        MAX-ACCESS  read-only
        STATUS      current
        DESCRIPTION
          "TFS bit rate may be specified at layer 3 packet rate.
          On Transmission, target bandwidth/bit rate in bps for
          iptfs tunnel.  This rate is the nominal timing for the
          fixed size packet. If congestion control is enabled the
          rate may be adjusted down (or up if unset)."
        ::= { iptfsConfigTableEntry 6 }

    dontFragment OBJECT-TYPE
        SYNTAX      TruthValue
        MAX-ACCESS  read-only
        STATUS      current
        DESCRIPTION
          "On transmission, disable packet fragmentation across
          consecutive iptfs tunnel packets; inner packets larger
          than what can be transmitted in outer packets will be
          dropped."
        ::= { iptfsConfigTableEntry 7 }

    maxAggregationTime OBJECT-TYPE
        SYNTAX      NanoSeconds
        MAX-ACCESS  read-only
        STATUS      current
        DESCRIPTION
          "On transmission, maximum aggregation time is the
           maximum length of time a received inner packet can be
           held prior to transmission in the iptfs tunnel. Inner
           packets that would be held longer than this time, based
           on the current tunnel configuration will be dropped
           rather than be queued for transmission."
        ::= { iptfsConfigTableEntry 8 }

    windowSize OBJECT-TYPE
        SYNTAX      Unsigned32(0..65535)
        MAX-ACCESS  read-only
        STATUS      current
        DESCRIPTION
          "On reception, the maximum number of out-of-order
          packets that will be reordered by an iptfs receiver
          while performing the reordering operation. The value 0
          disables any reordering."
        ::= { iptfsConfigTableEntry 9 }

    sendImmediately OBJECT-TYPE
        SYNTAX      TruthValue
        MAX-ACCESS  read-only
        STATUS      current
        DESCRIPTION
          "On reception, send inner packets as soon as possible, do
          not wait for lost or misordered outer packets.
          Selecting this option reduces the inner (user) packet
          delay but can amplify out-of-order delivery of the inner
          packet stream in the presence of packet aggregation and
          any reordering."
        ::= { iptfsConfigTableEntry 10 }

    lostPktTimerInt OBJECT-TYPE
        SYNTAX      NanoSeconds
        MAX-ACCESS  read-only
        STATUS      current
        DESCRIPTION
          "On reception, this interval defines the length of time
          an iptfs receiver will wait for a missing packet before
          considering it lost.  If not using send-immediately,
          then each lost packet will delay inner (user) packets
          until this timer expires. Setting this value too low can
          impact reordering and reassembly."
        ::= { iptfsConfigTableEntry 11 }

   ipsecStatsTable OBJECT-TYPE
       SYNTAX     SEQUENCE OF IpsecStatsTableEntry
       MAX-ACCESS not-accessible
       STATUS     current
       DESCRIPTION
         "The table containing basic statistics on IPsec."
       ::= { ipsecStatsGroup 1 }


    ipsecStatsTableEntry OBJECT-TYPE
       SYNTAX     IpsecStatsTableEntry
       MAX-ACCESS not-accessible
       STATUS     current
       DESCRIPTION
         "An entry (conceptual row) containing the information on
         a particular IKE SA."
       INDEX      { ipsecSaIndex }
       ::= { ipsecStatsTable 1 }

     IpsecStatsTableEntry ::= SEQUENCE {
     ipsecSaIndex               Integer32,
-- packet statistics information
     txPackets                  Counter64,
     txOctets                   Counter64,
     txDropPackets              Counter64,
     rxPackets                  Counter64,
     rxOctets                   Counter64,
     rxDropPackets              Counter64
   }

   ipsecSaIndex OBJECT-TYPE
      SYNTAX      Integer32 (1..16777215)
      MAX-ACCESS  not-accessible
      STATUS      current
      DESCRIPTION
        "A unique value, greater than zero, for each SA.
        It is recommended that values are assigned contiguously
        starting from 1.

        The value for each entry must remain constant at least
        from one re-initialization of entity's network management
        system to the next re-initialization."
      ::= { ipsecStatsTableEntry 1 }


   txPackets OBJECT-TYPE
       SYNTAX      Counter64
       MAX-ACCESS  read-only
       STATUS      current
       DESCRIPTION
         "Outbound Packet count."
       ::= { ipsecStatsTableEntry 2 }

   txOctets OBJECT-TYPE
       SYNTAX      Counter64
       MAX-ACCESS  read-only
       STATUS      current
       DESCRIPTION
         "Outbound Packet bytes."
       ::= { ipsecStatsTableEntry 3 }

   txDropPackets OBJECT-TYPE
       SYNTAX      Counter64
       MAX-ACCESS  read-only
       STATUS      current
       DESCRIPTION
         "Outbound dropped packets count."
       ::= { ipsecStatsTableEntry 4 }

   rxPackets OBJECT-TYPE
       SYNTAX      Counter64
       MAX-ACCESS  read-only
       STATUS      current
       DESCRIPTION
         "Inbound Packet count."
       ::= { ipsecStatsTableEntry 5 }

   rxOctets OBJECT-TYPE
       SYNTAX      Counter64
       MAX-ACCESS  read-only
       STATUS      current
       DESCRIPTION
         "Inbound Packet bytes."
       ::= { ipsecStatsTableEntry 6 }

   rxDropPackets OBJECT-TYPE
       SYNTAX      Counter64
       MAX-ACCESS  read-only
       STATUS      current
       DESCRIPTION
         "Inbound Dropped packets"
       ::= { ipsecStatsTableEntry 7 }

   iptfsInnerStatsTable OBJECT-TYPE
       SYNTAX     SEQUENCE OF IptfsInnerSaEntry
       MAX-ACCESS not-accessible
       STATUS     current
       DESCRIPTION
         "The table containing information on IPTFS
         Inner Packets."
       ::= { iptfsInnerStatsGroup 1 }

   iptfsInnerStatsTableEntry OBJECT-TYPE
      SYNTAX     IptfsInnerSaEntry
      MAX-ACCESS not-accessible
      STATUS     current
      DESCRIPTION
        "An entry containing the information on
        a particular tfs SA."
      INDEX      { iptfsInnerSaIndex }
      ::= { iptfsInnerStatsTable 1 }

     IptfsInnerSaEntry ::= SEQUENCE {
     iptfsInnerSaIndex          Integer32,

     txInnerPackets             Counter64,
     txInnerOctets              Counter64,
     rxInnerPackets             Counter64,
     rxInnerOctets              Counter64,
     rxIncompleteInnerPackets   Counter64
    }

   iptfsInnerSaIndex OBJECT-TYPE
      SYNTAX      Integer32 (1..16777215)
      MAX-ACCESS  not-accessible
      STATUS      current
      DESCRIPTION
        "A unique value, greater than zero, for each SA.
        It is recommended that values are assigned contiguously
        starting from 1.

        The value for each entry must remain constant at least
        from one re-initialization of entity's network management
        system to the next re-initialization."
      ::= { iptfsInnerStatsTableEntry 1 }

   txInnerPackets OBJECT-TYPE
       SYNTAX      Counter64
       MAX-ACCESS  read-only
       STATUS      current
       DESCRIPTION
         "Total number of IP-TFS inner packets sent. This count
         is whole packets only.  A fragmented packet counts as
         one packet."
       ::= { iptfsInnerStatsTableEntry 2 }

   txInnerOctets OBJECT-TYPE
       SYNTAX      Counter64
       MAX-ACCESS  read-only
       STATUS      current
       DESCRIPTION
         "Total number of IP-TFS inner octets sent.  This is
         inner packet octets only.  Does not count padding."
       ::= { iptfsInnerStatsTableEntry 3 }

   rxInnerPackets OBJECT-TYPE
       SYNTAX      Counter64
       MAX-ACCESS  read-only
       STATUS      current
       DESCRIPTION
         "Total number of IP-TFS inner packets received."
       ::= { iptfsInnerStatsTableEntry 4 }

       rxInnerOctets OBJECT-TYPE
       SYNTAX      Counter64
       MAX-ACCESS  read-only
       STATUS      current
       DESCRIPTION
         "Total number of IP-TFS inner octets received.  Does
         not include padding or overhead."
       ::= { iptfsInnerStatsTableEntry 5 }

   rxIncompleteInnerPackets OBJECT-TYPE
       SYNTAX      Counter64
       MAX-ACCESS  read-only
       STATUS      current
       DESCRIPTION
         "Total number of IP-TFS inner packets that were
         incomplete.  Usually this is due to fragments not
         received. Also, this may be due to misordering or
         errors in received outer packets."
    ::= { iptfsInnerStatsTableEntry 6 }

  iptfsOuterStatsTable OBJECT-TYPE
       SYNTAX     SEQUENCE OF IptfsOuterSaEntry
       MAX-ACCESS not-accessible
       STATUS     current
       DESCRIPTION
         "The table containing information on IPTFS."
       ::= { iptfsOuterStatsGroup 1 }

   iptfsOuterStatsTableEntry OBJECT-TYPE
      SYNTAX     IptfsOuterSaEntry
      MAX-ACCESS not-accessible
      STATUS     current
      DESCRIPTION
        "An entry containing the information on
        a particular tfs SA."
      INDEX      { iptfsSaIndex }
      ::= { iptfsOuterStatsTable 1 }

     IptfsOuterSaEntry ::= SEQUENCE {
     iptfsSaIndex               Integer32,

  -- iptfs packet statistics information
     txExtraPadPackets          Counter64,
     txExtraPadOctets           Counter64,
     txAllPadPackets            Counter64,
     txAllPadOctets             Counter64,
     rxExtraPadPackets          Counter64,
     rxExtraPadOctets           Counter64,
     rxAllPadPackets            Counter64,
     rxAllPadOctets             Counter64,
     rxErroredPackets           Counter64,
     rxMissedPackets            Counter64
    }


   iptfsSaIndex OBJECT-TYPE
      SYNTAX      Integer32 (1..16777215)
      MAX-ACCESS  not-accessible
      STATUS      current
      DESCRIPTION
        "A unique value, greater than zero, for each SA.
        It is recommended that values are assigned contiguously
        starting from 1.

        The value for each entry must remain constant at least
        from one re-initialization of entity's network management
        system to the next re-initialization."
      ::= { iptfsOuterStatsTableEntry 1 }

   txExtraPadPackets OBJECT-TYPE
       SYNTAX      Counter64
       MAX-ACCESS  read-only
       STATUS      current
       DESCRIPTION
         "Total number of transmitted outer IP-TFS packets that
         included some padding."
       ::= { iptfsOuterStatsTableEntry 2 }

   txExtraPadOctets OBJECT-TYPE
       SYNTAX      Counter64
       MAX-ACCESS  read-only
       STATUS      current
       DESCRIPTION
         "Total number of transmitted octets of padding added to
         outer IP-TFS packets with data."
       ::= { iptfsOuterStatsTableEntry 3 }

   txAllPadPackets OBJECT-TYPE
       SYNTAX      Counter64
       MAX-ACCESS  read-only
       STATUS      current
       DESCRIPTION
         "Total number of transmitted IP-TFS packets that were
         all padding with no inner packet data."
       ::= { iptfsOuterStatsTableEntry 4 }

   txAllPadOctets OBJECT-TYPE
       SYNTAX      Counter64
       MAX-ACCESS  read-only
       STATUS      current
       DESCRIPTION
         "Total number transmitted octets of padding added to
         IP-TFS packets with no inner packet data."
       ::= { iptfsOuterStatsTableEntry 5 }

   rxExtraPadPackets OBJECT-TYPE
       SYNTAX      Counter64
       MAX-ACCESS  read-only
       STATUS      current
       DESCRIPTION
         "Total number of received outer IP-TFS packets that
         included some padding."
       ::= { iptfsOuterStatsTableEntry 6 }

   rxExtraPadOctets OBJECT-TYPE
       SYNTAX      Counter64
       MAX-ACCESS  read-only
       STATUS      current
       DESCRIPTION
         "Total number of received octets of padding added to
         outer IP-TFS packets with data."
       ::= { iptfsOuterStatsTableEntry 7 }

   rxAllPadPackets OBJECT-TYPE
       SYNTAX      Counter64
       MAX-ACCESS  read-only
       STATUS      current
       DESCRIPTION
         "Total number of received IP-TFS packets that were all
         padding with no inner paccket data."
       ::= { iptfsOuterStatsTableEntry 8 }

   rxAllPadOctets OBJECT-TYPE
       SYNTAX      Counter64
       MAX-ACCESS  read-only
       STATUS      current
       DESCRIPTION
         "Total number received octets of padding added to
         IP-TFS packets with no inner packet data."
       ::= { iptfsOuterStatsTableEntry 9 }

   rxErroredPackets OBJECT-TYPE
       SYNTAX      Counter64
       MAX-ACCESS  read-only
       STATUS      current
       DESCRIPTION
         "Total number of IP-TFS outer packets dropped due to
         errors."
       ::= { iptfsOuterStatsTableEntry 10 }

   rxMissedPackets OBJECT-TYPE
       SYNTAX      Counter64
       MAX-ACCESS  read-only
       STATUS      current
       DESCRIPTION
         "Total number of IP-TFS outer packets missing indicated
         by missing sequence number."
       ::= { iptfsOuterStatsTableEntry 11 }

--
-- Iptfs Module Compliance
--

iptfsMIBConformances OBJECT IDENTIFIER
                    ::= { iptfsMIBConformance 1 }

iptfsMIBGroups OBJECT IDENTIFIER
                    ::= { iptfsMIBConformance 2 }

iptfsMIBCompliance MODULE-COMPLIANCE
        STATUS  current
        DESCRIPTION
                "The compliance statement for entities which
                implement the IPTFS MIB"
        MODULE  -- this module
                MANDATORY-GROUPS {
                 iptfsMIBConfGroup,
                 ipsecStatsConfGroup,
                 iptfsInnerStatsConfGroup,
                 iptfsOuterStatsConfGroup
                }

        ::= { iptfsMIBConformances 1 }

--
-- MIB Groups (Units of Conformance)
--

iptfsMIBConfGroup OBJECT-GROUP
        OBJECTS {
                congestionControl,
                usePathMtu,
                outerPacketSize ,
                l2FixedRate ,
                l3FixedRate ,
                dontFragment,
                maxAggregationTime,
                windowSize,
                sendImmediately,
                lostPktTimerInt
        }
        STATUS  current
        DESCRIPTION
                "A collection of objects providing per SA IPTFS
                Configuration."
        ::= { iptfsMIBGroups 1 }

ipsecStatsConfGroup OBJECT-GROUP
        OBJECTS {
                txPackets,
                txOctets,
                txDropPackets,
                rxPackets,
                rxOctets,
                rxDropPackets
        }
        STATUS  current
        DESCRIPTION
          "A collection of objects providing per SA Basic
          Stats."
        ::= { iptfsMIBGroups 2 }

iptfsInnerStatsConfGroup OBJECT-GROUP
        OBJECTS {
                txInnerPackets,
                txInnerOctets,
                rxInnerPackets,
                rxInnerOctets,
                rxIncompleteInnerPackets
        }
        STATUS  current
        DESCRIPTION
          "A collection of objects providing per SA IPTFS
          Inner Packet Statistics."
        ::= { iptfsMIBGroups 3 }


iptfsOuterStatsConfGroup OBJECT-GROUP
        OBJECTS {
                txExtraPadPackets,
                txExtraPadOctets,
                txAllPadPackets,
                txAllPadOctets,
                rxExtraPadPackets,
                rxExtraPadOctets,
                rxAllPadPackets,
                rxAllPadOctets,
                rxErroredPackets,
                rxMissedPackets
        }
        STATUS  current
        DESCRIPTION
          "A collection of objects providing per SA IPTFS
          Outer Packet Statistics."
        ::= { iptfsMIBGroups 4 }

END

5. IANA Considerations

The MIB module in this document uses the following IANA-assigned OBJECT IDENTIFIER value, recorded in the SMI Numbers registry:

         +------------+-------------------------+
         | Descriptor | OBJECT IDENTIFIER value |
         +------------+-------------------------+
         | iptfs      | TBA  IANA               |
         +------------+-------------------------+
         | ipsec      | TBA  IANA               |
         +------------+-------------------------+

6. Security Considerations

The MIB specified in this document can read the operational and configured behavior of IP traffic flow security, for the implications regarding write configuration consult the [I-D.ietf-ipsecme-iptfs] which defines the functionality.

There are no management objects defined in this MIB module that have a MAX-ACCESS clause of read-write and/or read-create. So, if this MIB module is implemented correctly, then there is no risk that an intruder can alter or create any management objects of this MIB module via direct SNMP SET operations.

Some of the objects in this MIB module may be considered sensitive or vulnerable in some network environments. This includes INDEX objects with a MAX-ACCESS of not-accessible, and any indices from other modules exposed via AUGMENTS. It is thus important to control even GET and/or NOTIFY access to these objects and possibly to even encrypt the values of these objects when sending them over the network via SNMP. These are the tables and objects and their sensitivity/vulnerability:

SNMP versions prior to SNMPv3 did not include adequate security. Even if the network itself is secure (for example by using IPsec), there is no control as to who on the secure network is allowed to access and GET/SET (read/change/create/delete) the objects in this MIB module.

Implementations SHOULD provide the security features described by the SNMPv3 framework (see [RFC3410]), and implementations claiming compliance to the SNMPv3 standard MUST include full support for authentication and privacy via the User-based Security Model (USM) [RFC3414] with the AES cipher algorithm [RFC3826]. Implementations MAY also provide support for the Transport Security Model (TSM) [RFC5591] in combination with a secure transport such as SSH [RFC5592] or TLS/DTLS [RFC6353].

Further, deployment of SNMP versions prior to SNMPv3 is NOT RECOMMENDED. Instead, it is RECOMMENDED to deploy SNMPv3 and to enable cryptographic security. It is then a customer/operator responsibility to ensure that the SNMP entity giving access to an instance of this MIB module is properly configured to give access to the objects only to those principals (users) that have legitimate rights to indeed GET or SET (change/create/delete) them.

7. Acknowledgements

The authors would like to thank Chris Hopps, Lou Berger and Tero Kivinen for their help and feedback on the MIB model.

8. References

8.1. Normative References

[I-D.ietf-ipsecme-iptfs]
Hopps, C., "IP-TFS: Aggregation and Fragmentation Mode for ESP and its Use for IP Traffic Flow Security", Work in Progress, Internet-Draft, draft-ietf-ipsecme-iptfs-12, , <https://www.ietf.org/archive/id/draft-ietf-ipsecme-iptfs-12.txt>.
[I-D.ietf-ipsecme-yang-iptfs]
Fedyk, D. and C. Hopps, "A YANG Data Model for IP Traffic Flow Security", Work in Progress, Internet-Draft, draft-ietf-ipsecme-yang-iptfs-03, , <https://www.ietf.org/archive/id/draft-ietf-ipsecme-yang-iptfs-03.txt>.
[RFC2119]
Bradner, S., "Key words for use in RFCs to Indicate Requirement Levels", BCP 14, RFC 2119, DOI 10.17487/RFC2119, , <https://www.rfc-editor.org/info/rfc2119>.
[RFC2578]
McCloghrie, K., Ed., Perkins, D., Ed., and J. Schoenwaelder, Ed., "Structure of Management Information Version 2 (SMIv2)", STD 58, RFC 2578, DOI 10.17487/RFC2578, , <https://www.rfc-editor.org/info/rfc2578>.
[RFC2579]
McCloghrie, K., Ed., Perkins, D., Ed., and J. Schoenwaelder, Ed., "Textual Conventions for SMIv2", STD 58, RFC 2579, DOI 10.17487/RFC2579, , <https://www.rfc-editor.org/info/rfc2579>.
[RFC3410]
Case, J., Mundy, R., Partain, D., and B. Stewart, "Introduction and Applicability Statements for Internet-Standard Management Framework", RFC 3410, DOI 10.17487/RFC3410, , <https://www.rfc-editor.org/info/rfc3410>.
[RFC3414]
Blumenthal, U. and B. Wijnen, "User-based Security Model (USM) for version 3 of the Simple Network Management Protocol (SNMPv3)", STD 62, RFC 3414, DOI 10.17487/RFC3414, , <https://www.rfc-editor.org/info/rfc3414>.
[RFC3826]
Blumenthal, U., Maino, F., and K. McCloghrie, "The Advanced Encryption Standard (AES) Cipher Algorithm in the SNMP User-based Security Model", RFC 3826, DOI 10.17487/RFC3826, , <https://www.rfc-editor.org/info/rfc3826>.
[RFC5591]
Harrington, D. and W. Hardaker, "Transport Security Model for the Simple Network Management Protocol (SNMP)", STD 78, RFC 5591, DOI 10.17487/RFC5591, , <https://www.rfc-editor.org/info/rfc5591>.
[RFC5592]
Harrington, D., Salowey, J., and W. Hardaker, "Secure Shell Transport Model for the Simple Network Management Protocol (SNMP)", RFC 5592, DOI 10.17487/RFC5592, , <https://www.rfc-editor.org/info/rfc5592>.
[RFC6353]
Hardaker, W., "Transport Layer Security (TLS) Transport Model for the Simple Network Management Protocol (SNMP)", STD 78, RFC 6353, DOI 10.17487/RFC6353, , <https://www.rfc-editor.org/info/rfc6353>.
[RFC8174]
Leiba, B., "Ambiguity of Uppercase vs Lowercase in RFC 2119 Key Words", BCP 14, RFC 8174, DOI 10.17487/RFC8174, , <https://www.rfc-editor.org/info/rfc8174>.

8.2. Informative References

[RFC2580]
McCloghrie, K., Ed., Perkins, D., Ed., and J. Schoenwaelder, Ed., "Conformance Statements for SMIv2", STD 58, RFC 2580, DOI 10.17487/RFC2580, , <https://www.rfc-editor.org/info/rfc2580>.
[RFC4301]
Kent, S. and K. Seo, "Security Architecture for the Internet Protocol", RFC 4301, DOI 10.17487/RFC4301, , <https://www.rfc-editor.org/info/rfc4301>.
[RFC5348]
Floyd, S., Handley, M., Padhye, J., and J. Widmer, "TCP Friendly Rate Control (TFRC): Protocol Specification", RFC 5348, DOI 10.17487/RFC5348, , <https://www.rfc-editor.org/info/rfc5348>.

Authors' Addresses

Don Fedyk
LabN Consulting, L.L.C.
Eric Kinzie
LabN Consulting, L.L.C.

mirror server hosted at Truenetwork, Russian Federation.