| Internet-Draft | IP Parcels | March 2022 |
| Templin | Expires 30 September 2022 | [Page] |
IP packets (both IPv4 and IPv6) are understood to contain a unit of data which becomes the retransmission unit in case of loss. Upper layer protocols such as the Transmission Control Protocol (TCP) prepare data units known as "segments", with traditional arrangements including a single segment per packet. This document presents a new construct known as the "IP Parcel" which permits a single packet to carry multiple segments, essentially creating a "packet-of-packets". IP parcels provide an essential building block for accommodating larger Maximum Transmission Units (MTUs) in the Internet as discussed in this document.¶
This Internet-Draft is submitted in full conformance with the provisions of BCP 78 and BCP 79.¶
Internet-Drafts are working documents of the Internet Engineering Task Force (IETF). Note that other groups may also distribute working documents as Internet-Drafts. The list of current Internet-Drafts is at https://datatracker.ietf.org/drafts/current/.¶
Internet-Drafts are draft documents valid for a maximum of six months and may be updated, replaced, or obsoleted by other documents at any time. It is inappropriate to use Internet-Drafts as reference material or to cite them other than as "work in progress."¶
This Internet-Draft will expire on 30 September 2022.¶
Copyright (c) 2022 IETF Trust and the persons identified as the document authors. All rights reserved.¶
This document is subject to BCP 78 and the IETF Trust's Legal Provisions Relating to IETF Documents (https://trustee.ietf.org/license-info) in effect on the date of publication of this document. Please review these documents carefully, as they describe your rights and restrictions with respect to this document. Code Components extracted from this document must include Revised BSD License text as described in Section 4.e of the Trust Legal Provisions and are provided without warranty as described in the Revised BSD License.¶
IP packets (both IPv4 [RFC0791] and IPv6 [RFC8200]) are understood to contain a unit of data which becomes the retransmission unit in case of loss. Upper layer protocols such as the Transmission Control Protocol (TCP) [RFC0793], QUIC [RFC9000], LTP [RFC5326] and others prepare data units known as "segments", with traditional arrangements including a single segment per packet. This document presents a new construct known as the "IP Parcel" which permits a single packet to carry multiple segments. This essentially creates a "packet-of-packets" with the IP layer headers appearing only once but with possibly multiple upper layer protocol segments included.¶
Parcels are formed when an upper layer protocol entity identified by the "5-tuple" (source IP, source port, destination IP, destination port, protocol number) prepares a data buffer with the concatenation of up to 64 properly-formed segments that can be broken out into smaller parcels using a copy of the IP header. All segments except the final segment must be equal in size and no larger than 65535 octets (minus headers), while the final segment must not be larger than the others but may be smaller. The upper layer protocol entity then delivers the buffer and non-final segment size to the IP layer, which appends the necessary IP header plus extensions to identify this as a parcel and not an ordinary packet.¶
Parcels can be forwarded over consecutive parcel-capable IP links in the path until arriving at an ingress middlebox at the edge of an intermediate Internetwork. The ingress middlebox may break the parcel out into smaller (sub-)parcels and encapsulate them in headers suitable for traversing the Internetwork. These smaller parcels may then be rejoined into one or more larger parcels at an egress middlebox which either delivers them locally or forwards them further over parcel-capable IP links toward the final destination. Middlebox repackaging of parcels is therefore possible, making reordering and even loss of individual segments possible. But, what matters is that the number of parcels delivered to the final destination should be kept to a minimum, and that loss or receipt of individual segments (and not parcel size) determines the retransmission unit.¶
The following sections discuss rationale for creating and shipping parcels as well as the actual protocol constructs and procedures involved. IP parcels provide an essential building block for accommodating larger Maximum Transmission Units (MTUs) in the Internet. It is further expected that the parcel concept may drive future innovation in applications, operating systems, network equipment and data links.¶
A "parcel" is defined as "a thing or collection of things wrapped in paper in order to be carried or sent by mail". Indeed, there are many examples of parcel delivery services worldwide that provide an essential transit backbone for efficient business and consumer transactions.¶
In this same spirit, an "IP parcel" is simply a collection of up to 64 upper layer protocol segments wrapped in an efficient package for transmission and delivery (i.e., a "packet-of-packets") while a "singleton IP parcel" is simply a parcel that contains a single segment. IP parcels are distinguished from ordinary packets through the special header constructions discussed in this document.¶
The IP parcels construct is defined for both IPv4 and IPv6. Where the document refers to "IPv4 header length", it means the total length of the base IPv4 header plus all included options, i.e., as determined by consulting the Internet Header Length (IHL) field. Where the document refers to "IPv6 header length", however, it means only the length of the base IPv6 header (i.e., 40 octets), while the length of any extension headers is referred to separately as the "extension header length". Finally, the term "IP header plus extensions" refers generically to an IPv4 header plus all included options or an IPv6 header plus all included extension headers.¶
The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT", "SHOULD", "SHOULD NOT", "RECOMMENDED", "NOT RECOMMENDED", "MAY", and "OPTIONAL" in this document are to be interpreted as described in BCP 14 [RFC2119][RFC8174] when, and only when, they appear in all capitals, as shown here.¶
Studies have shown that applications can realize greater performance by sending and receiving larger packets due to reduced numbers of system calls and interrupts as well as larger atomic data copies between kernel and user space. Large packets also result in reduced numbers of network device interrupts and better network utilization in comparison with smaller packet sizes.¶
A first study [QUIC] involved performance enhancement of the QUIC protocol [RFC9000] using the linux Generic Segment/Receive Offload (GSO/GRO) facility. GSO/GRO provide a robust (but non-standard) service very similar in nature to the IP parcel service described here, and its application has shown significant performance increases due to the increased transfer unit size between the operating system kernel and QUIC application.¶
A second study [I-D.templin-dtn-ltpfrag] showed that GSO/GRO also improved performance for the Licklider Transmission Protocol (LTP) [RFC5326] for small- to medium-sized segments. Historically, the NFS protocol also saw significant performance increases using larger (single-segment) UDP datagrams even when IP fragmentation is invoked, and LTP still follows this profile today. Moreover, LTP shows this (single-segment) performance increase profile extending to the largest possible segment size which suggests that additional performance gains may be possible using (multi-segment) IP parcels that exceed 65535 octets.¶
TCP also benefits from larger packet sizes and efforts have investigated TCP performance using jumbograms internally with changes to the linux GSO/GRO facilities [BIG-TCP]. The idea is to use the jumbo payload internally and to allow GSO/GRO to use buffer sizes larger than 65535 octets, but with the understanding that links that support jumbos natively are not yet widely available. Hence, IP parcels provides a packaging that can be considered in the near term under current deployment limitations.¶
A limiting consideration for sending large packets is that they are often lost at links with smaller Maximum Transmission Units (MTUs), and the resulting Packet Too Big (PTB) message may be lost somewhere in the path back to the original source. This "Path MTU black hole" condition can degrade performance unless robust path probing techniques are used, however the best case performance always occurs when no packets are lost due to size restrictions.¶
These considerations therefore motivate a design where the maximum segment size should be no larger than 65535 octets (minus headers), while parcels that carry the segments may themselves be significantly larger. Then, even if a middlebox needs to sub-divide the parcels into smaller sub-parcels to forward further toward the final destination, an important performance optimization for the original source, final destination and network middleboxes can be realized.¶
An analogy: when a consumer orders 50 small items from a major online retailer, the retailer does not ship the order in 50 separate small boxes. Instead, the retailer puts as many of the small items as possible into one or a few larger boxes (i.e., parcels) then places the parcels on a semi-truck or airplane. The parcels may then pass through one or more regional distribution centers where they may be repackaged into different parcel configurations and forwarded further until they are finally delivered to the consumer. But most often, the consumer will only find one or a few parcels at their doorstep and not 50 separate small boxes. This flexible parcel delivery service greatly reduces shipping and handling overhead for all including the retailer, regional distribution centers and finally the consumer.¶
IP parcel formation is invoked by an upper layer protocol (identified by the 5-tuple described above) when it prepares a data buffer containing the concatenation of up to 64 segments. All non-final segments MUST be equal in length while the final segment MUST NOT be larger and MAY be smaller. Each non-final segment MUST NOT be larger than 65535 octets minus the length of the IPv4 header or IPv6 extension headers, minus the length of an additional IPv6 header in case an encapsulation middlebox is visited on the path (see: Section 5). The upper layer protocol then presents the buffer and non-final segment size to the IP layer which appends a single IP header (plus extensions) before presenting the parcel either to an adaptation layer interface or directly to an ordinary network interface without engaging the adaptation layer (see: Section 5).¶
For IPv4, the IP layer prepares the parcel by appending an IPv4 header with a Jumbo Payload option formed as follows:¶
+--------+--------+--------+--------+--------+--------+ |Opt Type|Opt Len | Jumbo Payload Length | +--------+--------+--------+--------+--------+--------+¶
The IPv4 Jumbo Payload option format is identical to that defined in [RFC2675], except that the IP layer sets option type to '00001011' and option length to '00000110' noting that the length distinguishes this type from its deprecated use as the IPv4 "Probe MTU" option [RFC1063]. The IP layer then sets "Jumbo Payload Length" to the lengths of the IPv4 header plus the combined length of all concatenated segments (i.e., as a 32-bit value in network byte order). The IP layer next sets the IPv4 header DF bit to 1, then sets the IPv4 header Total Length field to the length of the IPv4 header plus the length of the first segment only. Note that the IP layer can form true IPv4 jumbograms (as opposed to parcels) by instead setting the IPv4 header Total Length field to the length of the IPv4 header only (see: Section 9).¶
For IPv6, the IP layer forms a parcel by appending an IPv6 header with a Hop-by-Hop Options extension header containing a Jumbo Payload option formatted the same as for IPv4 above, but with option type set to '11000010' and option length set to '00000100'. The IP layer then sets "Jumbo Payload Length" to the lengths of all IPv6 extension headers present plus the combined length of all concatenated segments. The IP layer next sets the IPv6 header Payload Length field to the lengths of all IPv6 extension headers present plus the length of the first segment only. Note that the IP layer can form true IPv6 jumbograms (as opposed to parcels) by instead setting the IPv6 header Payload Length field to 0 (see: [RFC2675]).¶
An IP parcel therefore has the following structure:¶
+--------+--------+--------+--------+
| |
~ Segment J (K octets) ~
| |
+--------+--------+--------+--------+
~ ~
~ ~
+--------+--------+--------+--------+
| |
~ Segment 3 (L octets) ~
| |
+--------+--------+--------+--------+
| |
~ Segment 2 (L octets) ~
| |
+--------+--------+--------+--------+
| |
~ Segment 1 (L octets) ~
| |
+--------+--------+--------+--------+
| IP Header Plus Extensions |
~ {Total, Payload} Length = M ~
| Jumbo Payload Length = N |
+--------+--------+--------+--------+
¶
where J is the total number of segments (between 1 and 64), L is the length of each non-final segment which MUST NOT be larger than 65535 octets (minus headers as above) and K is the length of the final segment which MUST NOT be larger than L. The values M and N are then set to the length of the IP header for IPv4 or to the length of the extension headers only for IPv6, then further calculated as follows:¶
Using TCP [RFC0793] for example, each of the J segments would include its own TCP header, including Sequence Number, Checksum, etc. The Sequence Number plus segment length (K or L) therefore provides the destination with the necessary parameters for application data reassembly while the Checksum provides per-segment application data integrity.¶
Note: a "singleton" parcel is one that includes only the IP header plus extensions with J=1 and a single segment of length K, while a "null" parcel is a singleton with (J=1; K=0), i.e., a parcel consisting of only the IP header plus extensions with no octets beyond.¶
The IP layer next presents the parcel to the outgoing network interface. For ordinary IP interfaces, the interface simply forwards the parcel over the underlying link the same as for any IP packet after which it may then be forwarded by any number of routers over additional consecutive parcel-capable IP links. If any next hop IP link in the path either does not support parcels or configures an MTU that is too small to transit the parcel without fragmentation, the router instead opens the parcel and forwards each enclosed segment as a separate IP packet (i.e., by appending a copy of the parcel's IP header to each segment but with the Jumbo Payload option removed according to the standards [RFC0791][RFC8200]). Or, if the router does not recognize parcels at all, it drops the parcel and may return an ICMP "Parameter Problem" message.¶
If the outgoing network interface is an OMNI interface [I-D.templin-6man-omni], the OMNI Adaptation Layer (OAL) of this First Hop Segment (FHS) OAL source node forwards the parcel to the next OAL hop which may be either an OAL intermediate node or a Last Hop Segment (LHS) OAL destination node (which may also be the final destination itself). The OAL source assigns a monotonically- incrementing (modulo 127) "Parcel ID" and subdivides the parcel into sub-parcels no larger than the maximum of the path MTU to the next hop or 65535 octets (minus headers) by determining the number of segments of length L that can fit into each sub-parcel under these size constraints. For example, if the OAL source determines that a sub-parcel can contain 3 segments of length L, it creates sub-parcels with the first containing segments 1-3, the second containing segments 4-6, etc. and with the final containing any remaining segments. The OAL source then appends an identical IP header plus extensions to each sub-parcel while resetting M and N in each according to the above equations with J set to 3 (and K = L) for each non-final sub-parcel and with J set to the remaining number of segments for the final sub-parcel.¶
The OAL source next performs IP encapsulation on each sub-parcel with destination set to the next hop IP address then inserts an IPv6 Fragment Header after the IP encapsulation header, i.e., even if the encapsulation header is IPv4, even if no actual fragmentation is needed and/or even if the Jumbo Payload option is present. The OAL source then assigns a randomly-initialized 32-bit Identification number that is monotonically-incremented for each consecutive sub-parcel, then performs IPv6 fragmentation over the sub-parcel if necessary to create fragments small enough to traverse the path to the next OAL hop while writing the Parcel ID and setting or clearing the "Parcel (P)" and "(More) Sub-Parcels (S)" bits in the Fragment Header of the first fragment (see: [I-D.templin-6man-fragrep]). (The OAL source sets P to 1 for a parcel or to 0 for a non-parcel. When P is 1, the OAL source next sets S to 1 for non-final sub-parcels or to 0 if the sub-parcel contains the final segment.) The OAL source then forwards each IP encapsulated packet/fragment to the next OAL hop.¶
When the next OAL hop receives the encapsulated IP fragments or whole packets, it reassembles if necessary. If the P flag in the first fragment is 0, the next hop then processes the reassembled entity as an ordinary IP packet; otherwise it continues processing as a sub-parcel. If the next hop is an OAL intermediate node, it retains the sub-parcels along with their Parcel ID and Identification values for a brief time in hopes of re-combining with peer sub-parcels of the same original parcel identified by the 4-tuple consisting of the IP encapsulation source and destination, Identification and Parcel ID. The combining entails the concatenation of the segments included in sub-parcels with the same Parcel ID and with Identification values within 64 of one another to create a larger sub-parcel possibly even as large as the entire original parcel. Order of concatenation is not important, with the exception that the final sub-parcel (i.e., the one with S set to 0) must occur as the final concatenation before transmission. The OAL intermediate node then appends a common IP header plus extensions to each re-combined sub-parcel while resetting M and N in each according to the above equations with J, K and L set accordingly.¶
This OAL intermediate node next forwards the re-combined sub-parcel(s) to the next hop toward the OAL destination using encapsulation the same as specified above. (The intermediate node MUST ensure that the S flag remains set to 0 in the sub-parcel that contains the final segment.) When the sub-parcel(s) arrive at the OAL destination, the OAL destination re-combines them into the largest possible sub-parcels while honoring the S flag as above. If the OAL destination is also the final destination, it delivers the sub-parcels to the IP layer which acts on the enclosed 5-tuple information supplied by the original source. Otherwise, the OAL destination forwards each sub-parcel toward the final destination the same as for an ordinary IP packet the same as discussed above.¶
Note: while the OAL destination and/or final destination could theoretically re-combine the sub-parcels of multiple different parcels with identical upper layer protocol 5-tuples and with non-final segments of identical length, this process could become complicated when the different parcels each have final segments of diverse lengths. Since this might interfere with any perceived performance advantages, the decision of whether and how to perform inter-parcel concatenation is an implementation matter.¶
Note: some IPv6 fragmentation and reassembly implementations may require a well-formed IPv6 header to perform their operations. When the encapsulation is based on IPv4, such implementations translate the encapsulation header into an IPv6 header with IPv4-Mapped IPv6 addresses before performing the fragmentation/reassembly operation, then restore the original IPv4 header before further processing.¶
To determine whether parcels are supported over at least a leading portion of the forward path toward the final destination, the original source can send a singleton IP parcel formatted as a "Parcel Probe" that may include an upper layer protocol probe segment (e.g., a data segment, an ICMP Echo Request message, etc.). The purpose of the probe is to elicit a "Parcel Reply" and possibly also an ordinary upper layer protocol probe reply from the final destination.¶
If the original source receives a positive Parcel Reply, it marks the path as "parcels supported" and ignores any ICMP [RFC0792][RFC4443] and/or Packet Too Big (PTB) messages [RFC1191][RFC8201] concerning the probe. If the original source instead receives a negative Parcel Reply or no reply, it marks the path as "parcels not supported" and may regard any ICMP and/or PTB messages concerning the probe (or its contents) as indications of a possible path MTU restriction.¶
The original source can therefore send Parcel Probes in parallel with sending real data as ordinary IP packets. If the original source receives a positive Parcel Reply, it can begin using IP parcels.¶
Parcel Probes use the Jumbo Payload option type (see: Section 4) but set a different option length and replace the option value with control information plus a 4-octet "Path MTU" value into which conformant middleboxes write the minimum link MTU observed in a similar fashion as described in [RFC1063][I-D.ietf-6man-mtu-option]. Parcel Probes can also include an upper layer protocol probe segment, e.g., per [RFC4821][RFC8899]. When an upper layer protocol probe segment is included, it appears immediately after the IP header plus extensions.¶
The original source sends Parcel Probes unidirectionally in the forward path toward the final destination to elicit a Parcel Reply, since it will often be the case that IP parcels are supported only in the forward path and not in the return path. Parcel Probes may be dropped in the forward path by any node that does not recognize IP parcels, but a Parcel Reply must not be dropped even if IP parcels are not recognized along portions of the return path. For this reason, Parcel Probes are packaged as IPv4 (header) options or IPv6 Hop-by-Hop options while Parcel Replys are always packaged as IPv6 Destination Options (i.e., regardless of the IP protocol version).¶
Original sources send Parcel Probes and Replys that include a Jumbo Payload option coded in an alternate format as follows:¶
+--------+--------+--------+--------+ |Opt Type|Opt Len | Nonce-1 | +--------+--------+--------+--------+ | Nonce-2 | +--------+--------+--------+--------+ | PMTU | +--------+--------+--------+--------+ | Code | Check | +--------+--------+¶
For IPv4, the original source includes the option as an IPv4 option with Type set to '00001011' the same as for an ordinary IPv4 parcel (see: Section 4) but with Length set to '00001110' to distinguish this as a probe/reply. The original source sets Nonce-1 to 0xffff, sets Nonce-2 to a (pseudo)-random 32-bit value and sets PMTU to the MTU of the outgoing IPv4 interface. The original source then sets Code to 0, sets Check to the same value that will appear in the TTL of the outgoing IPv4 header, then finally sets IPv4 Total Length to the lengths of the IPv4 header plus the upper layer protocol probe segment (if any) and sends the Parcel Probe via the outgoing IPv4 interface. According to [RFC7126], middleboxes (i.e., routers, security gateways, firewalls, etc.) that do not observe this specification SHOULD drop IP packets that contain option type '00001011' ("IPv4 Probe MTU") but some might instead either attempt to implement [RFC1063] or ignore the option altogether. IPv4 middleboxes that observe this specification instead MUST process the option as a Parcel Probe as specified below.¶
For IPv6, the original source includes the probe option as an IPv6 Hop-by-Hop option with Type set to '11000010' the same as for an ordinary IPv6 parcel (see: Section 4) but with Length set to '00001100' to distinguish this as a probe. The original source sets the concatenation of Nonce-1 and Nonce-2 to a (pseudo)-random 48-bit value and sets PMTU to the MTU of the outgoing IPv6 interface. The original source then sets Code to 0, sets Check to the same value that will appear in the Hop Limit of the outgoing IPv6 header, then finally sets IPv6 Payload Length to the lengths of the IPv6 extension headers plus the upper layer protocol probe segment (if any) and sends the Parcel Probe via the outgoing IPv6 interface. According to [RFC2675], middleboxes (i.e., routers, security gateways, firewalls, etc.) that recognize the IPv6 Jumbo Payload option but do not observe this specification SHOULD return an ICMPv6 Parameter Problem message (and presumably also drop the packet). IPv6 middleboxes that observe this specification instead MUST process the option as a Parcel Probe as specified below.¶
When a middlebox that observes this specification receives a Parcel Probe it first compares the Check value with the IP header Hop Limit/TTL; if the values differ, the middlebox MUST return a negative Parcel Reply (see below) and drop the probe. Otherwise, if the next hop IP link either does not support parcels or configures an MTU that is too small to pass the probe, the middlebox compares the PMTU value with the MTU of the inbound link for the probe and MUST (re)set PMTU to the lower MTU. The middlebox then MUST return a positive Parcel Reply (see below) and convert the probe into an ordinary IP packet by removing the probe option according to [RFC0791] or [RFC8200]. If the next hop IP link configures a sufficiently large MTU to pass the packet, the middlebox then MUST forward the packet to the next hop; otherwise, it MUST drop the packet and return a suitable PTB. If the next hop IP link both supports parcels and configures an MTU that is large enough to pass the probe, the middlebox instead compares the probe PMTU value with the MTUs of both the inbound and outbound links for the probe and MUST (re)set PMTU to the lower MTU. The middlebox then MUST reset Check to the same value that will appear in the TTL/Hop Limit of the outgoing IP header, and MUST forward the Parcel Probe to the next hop.¶
The final destination may therefore receive either an ordinary IP packet containing an upper layer protocol probe or a Parcel Probe. If the final destination receives an ordinary IP packet, it performs any necessary integrity checks then delivers the packet to upper layers which will return an upper layer probe response. If the final destination instead receives a Parcel Probe, it first compares the Check value with the IP header Hop Limit/TTL; if the values differ, the final destination MUST drop the probe and return a negative Parcel Reply (see below). Otherwise, the final destination compares the probe PMTU value with the MTU of the inbound link and MUST (re)set PMTU to the lower MTU. The final destination then MUST return a positive Parcel Reply (see below) and convert the probe into an ordinary IP packet by removing the Parcel Probe option according to the standards [RFC0791][RFC8200].The final destination then performs any necessary integrity checks and delivers the packet to upper layers.¶
When the middlebox or final destination returns a Parcel Reply, it prepares an IP header of the same protocol version that appeared in the Parcel Probe with source and destination addresses reversed, with {Protocol, Next Header} set to the value '60' (i.e., "IPv6 Destination Option") and with an IPv6 Destination Option header with Next Header set to the value '59' (i.e., "IPv6 No Next Header") [RFC8200]. The node next copies the body of the Parcel Probe option as the sole Parcel Reply Destination Option (and for IPv4 resets Type to '11000010' and Length to '00001100') and includes no other octets beyond the end of the option. The node then MUST (re)set Check to 1 for a positive or to 0 for a negative Parcel Reply, then MUST finally set the IP header {Total, Payload} Length field according to the length of the included Destination Option and return the Parcel Reply to the source. (Since filtering middleboxes may drop IPv4 packets with Protocol '60' the destination MUST wrap an IPv4 Parcel Reply in UDP/IPv4 headers with the IPv4 source and destination addresses copied from the Parcel Reply and with UDP port numbers set to the UDP port number for OMNI [I-D.templin-6man-omni].)¶
After sending a Parcel Probe the original source may therefore receive a Parcel Reply (see above) and/or an upper layer protocol probe reply. If the source receives a Parcel Reply, it first matches Nonce-2 (and for IPv6 only also matches Nonce-1) with the values it had included in the Parcel Probe. If the values do not match, the source discards the Parcel Reply. Next, the source examines the Check value and marks the path as "parcels supported" if the value is 1 or "parcels not supported" otherwise. If the source marks the path as "parcels supported", it also records the PMTU value as the maximum parcel size for the forward path to this destination.¶
After receiving a positive Parcel Reply, the original source can begin sending IP parcels addressed to the final destination up to the size recorded in the PMTU. Any upper layer protocol probe replies will determine the maximum segment size that can be included in the parcel, but this is an upper layer consideration. The original source should then periodically re-initiate Parcel Path Qualification as long as it continues to forward parcels toward the final destination (i.e., in case the forward path fluctuates). If at any time performance appears to degrade, the original source should cease sending IP parcels and/or re-initiate Parcel Path Qualification.¶
Note: For IPv4, the original source sets the Parcel Probe Nonce-1 field to 0xffff on transmission and ignores the Nonce-1 field value in any corresponding Parcel Replys. This avoids any possible confusion in case an IPv4 router on the path rewrites the Nonce-1 field in a wayward attempt to implement [RFC1063].¶
Note: The PMTU value returned in a positive Parcel Reply determines only the maximum IP parcel size for the path, while the maximum upper layer protocol segment size may be significantly smaller. The upper layer protocol segment size is instead determined separately according to any upper layer protocol probes and must be assumed to be no larger than 1/64th of the maximum IP parcel size unless a larger size is discovered by probing.¶
Each segment of a (multi-segment) IP parcel includes its own upper layer protocol integrity check. This means that IP parcels can support stronger integrity for the same amount of upper layer protocol data in comparison with an ordinary IP packet or Jumbogram containing only a single segment. The integrity checks must then be verified at the final destination, which accepts any segments with correct integrity while discarding all other segments and counting them as a loss event.¶
IP parcels can range in length from as small as only the IP headers themselves to as large as the IP headers plus (64 * (65535 minus headers)) octets. Although link layer integrity checks provide sufficient protection for contiguous data blocks up to approximately 9KB, reliance on the presence of link-layer integrity checks may not be possible over links such as tunnels. Moreover, the segment contents of a received parcel may arrive in an incomplete and/or rearranged order with respect to their original packaging.¶
For these reasons, the OAL at each hop of an OMNI link includes an integrity check when it performs IP fragmentation on a sub-parcel, with the integrity verified during reassembly at the next hop.¶
Section 3 of [RFC2675] provides a list of certain conditions to be considered as errors. In particular:¶
Implementations that obey this specification ignore these conditions and do not consider them as errors.¶
By defining a new IPv4 Jumbo Payload option, this document also implicitly enables a true IPv4 jumbogram service defined as an IPv4 packet with a Jumbo Payload option included and with Total Length set to the length of the IPv4 header only. All other aspects of IPv4 jumbograms are the same as for IPv6 jumbograms [RFC2675].¶
Common widely-deployed implementations include services such as TCP Segmentation Offload (TSO) and Generic Segmentation/Receive Offload (GSO/GRO). These services support a robust (but not standardized) service that has been shown to improve performance in many instances. Implementation of the IP parcel service is a work in progress.¶
The IANA is instructed to change the "MTUP - MTU Probe" entry in the 'ip option numbers' registry to the "JUMBO - IPv4 Jumbo Payload" option. The Copy and Class fields must both be set to 0, and the Number and Value fields must both be set to 11'. The reference must be changed to this document [RFCXXXX].¶
Original sources match the Nonce values in received Parcel Replies with their corresponding Parcel Probes. If the values match, the Parcel Reply is likely an authentic response to the Parcel Probe. In environments where stronger authentication is necessary, the message authentication services of OMNI can be applied [I-D.templin-6man-omni].¶
Multi-layer security solutions may be necessary to ensure confidentiality, integrity and availability in some environments.¶
This work was inspired by ongoing AERO/OMNI/DTN investigations. The concepts were further motivated through discussions on the intarea and 6man lists.¶
A considerable body of work over recent years has produced useful "segmentation offload" facilities available in widely-deployed implementations.¶
.¶