The following section covers the steps involved in creating the private key file, certificate signing request, and a self-signed certificate. If you plan to obtain a certificate signed by a certificate authority, you will need to create a certificate signing request (CSR). Otherwise, you can create a self-signed certificate.
To create a private key, you must have the OpenSSL toolkit installed and configured with Apache. The following examples use the OpenSSL command line tool which is located in the /usr/local/ssl/bin directory by default. The examples assume that the directory containing the OpenSSL command line tool has been added to the $PATH.
To create a private key using the triple des encryption standard (recommended), use the following command:
openssl genrsa -des3 -out filename.key 1024
You will be prompted to enter and re-enter a pass phrase. If you choose to use triple des encryption, you will be prompted for the password each time you start the SSL server from a cold start. (When using the restart command, you will not be prompted for the password). Some of you may find this password prompt to be a nuisance, especially if you need to boot the system during off-hours. Or, you may believe that your system is already sufficiently secure. So, if you choose not to have a password prompt (hence no triple des encryption), use the command below. If you would rather create just a 512-bit key, then omit the 1024 at the end of the command and OpenSSL will default to 512 bits. Using the smaller key is slightly faster, but it is also less secure.
To create a private key without triple des encryption, use the following command:
openssl genrsa -out filename.key 1024
To add a password to an existing private key, use the following command:
openssl -in filename.key -des3 -out newfilename.key
To remove a password from an existing private key, use the following command:
openssl -in filename.key -out newfilename.key
Note: Your private key will be created in the current directory unless
otherwise specified. There are 3 easy ways to deal with this. If OpenSSL
is in your path, you can run it from the directory that you have designated
to store your key files in (default is /etc/httpd/conf/ssl.key if you
installed Apache using the RPM or /usr/local/apache/conf/ssl.key if you
installed Apache using the source files). Another solution is to copy the
files from the directory where they were created to the correct directory.
And, last but not least, you can specify the path when running the command
(eg. openssl genrsa -out /etc/httpd/conf/ssl.key/filename.key 1024).
Doesn't matter how you do it as long as it gets done before you proceed.
For more information on the OpenSSL toolkit check out: OpenSSL Website.
To obtain a certificate signed by a certificate authority, you will need to create a Certificate Signing Request (CSR). The purpose is to send the certificate authority enough information to create the certificate without sending the entire private key or compromising any sensitive information. The CSR also contains the information that will be included in the certificate, such as, domain name, locality information, etc.
openssl req -new -key filename.key -out filename.csr
Note: Use the following command to create a private key and request at the same time.
openssl genrsa -des3 -out filename.key 1024
It is not necessary to create a self-signed certificate if you are obtaining a CA-signed certificate. However, creating a self-signed certificate is very simple. All you need is a private key and the name of the server (fully qualified domain name) that you want to secure. You will be prompted for information such as locality information, common name (domain name), organizational information, etc. OpenSSL gives you a great deal of freedom here. The only required field for the certificate to function correctly is the common name (domain name) field. If this is not present or incorrect, you will receive a Certificate Name Check warning from your browser.
To create a self-signed certificate:
openssl req -new -key filename.key -x509 -out filename.crt
If you followed these instructions so far you shouldn't have any problems at this point. If you sent your CSR to a certificate authority and you have not gotten your certificate back yet, you can take a break now! If you are using a self-signed certificate, or you have received your certificate, you may continue.
/etc/httpd/conf/ssl.key./etc/httpd/conf/ssl.crt. If it is not there already, put it there./etc/httpd/conf/ssl.crt directory, also.