This is a purely informative rendering of an RFC that includes verified errata. This rendering may not be used as a reference.
The following 'Verified' errata have been incorporated in this document:
EID 2713, EID 3896, EID 4485
Network Working Group C. Rigney
Request for Comments: 2866 Livingston
Category: Informational June 2000
Obsoletes: 2139
RADIUS Accounting
Status of this Memo
This memo provides information for the Internet community. It does
not specify an Internet standard of any kind. Distribution of this
memo is unlimited.
Copyright Notice
Copyright (C) The Internet Society (2000). All Rights Reserved.
Abstract
This document describes a protocol for carrying accounting
information between a Network Access Server and a shared Accounting
Server.
Implementation Note
This memo documents the RADIUS Accounting protocol. The early
deployment of RADIUS Accounting was done using UDP port number 1646,
which conflicts with the "sa-msg-port" service. The officially
assigned port number for RADIUS Accounting is 1813.
Table of Contents
1. Introduction .................................... 2
1.1 Specification of Requirements ................. 3
1.2 Terminology ................................... 3
2. Operation ....................................... 4
2.1 Proxy ......................................... 4
3. Packet Format ................................... 5
4. Packet Types ................................... 7
4.1 Accounting-Request ............................ 8
4.2 Accounting-Response ........................... 9
5. Attributes ...................................... 10
5.1 Acct-Status-Type .............................. 12
5.2 Acct-Delay-Time ............................... 13
5.3 Acct-Input-Octets ............................. 14
5.4 Acct-Output-Octets ............................ 15
5.5 Acct-Session-Id ............................... 15
5.6 Acct-Authentic ................................ 16
5.7 Acct-Session-Time ............................. 17
5.8 Acct-Input-Packets ............................ 18
5.9 Acct-Output-Packets ........................... 18
5.10 Acct-Terminate-Cause .......................... 19
5.11 Acct-Multi-Session-Id ......................... 21
5.12 Acct-Link-Count ............................... 22
5.13 Table of Attributes ........................... 23
6. IANA Considerations ............................. 25
7. Security Considerations ......................... 25
8. Change Log ...................................... 25
9. References ...................................... 26
10. Acknowledgements ................................ 26
11. Chair's Address ................................. 26
12. Author's Address ................................ 27
13. Full Copyright Statement ........................ 28
1. Introduction
Managing dispersed serial line and modem pools for large numbers of
users can create the need for significant administrative support.
Since modem pools are by definition a link to the outside world, they
require careful attention to security, authorization and accounting.
This can be best achieved by managing a single "database" of users,
which allows for authentication (verifying user name and password) as
well as configuration information detailing the type of service to
deliver to the user (for example, SLIP, PPP, telnet, rlogin).
The RADIUS (Remote Authentication Dial In User Service) document [2]
specifies the RADIUS protocol used for Authentication and
Authorization. This memo extends the use of the RADIUS protocol to
cover delivery of accounting information from the Network Access
Server (NAS) to a RADIUS accounting server.
This document obsoletes RFC 2139 [1]. A summary of the changes
between this document and RFC 2139 is available in the "Change Log"
appendix.
Key features of RADIUS Accounting are:
Client/Server Model
A Network Access Server (NAS) operates as a client of the
RADIUS accounting server. The client is responsible for
passing user accounting information to a designated RADIUS
accounting server.
The RADIUS accounting server is responsible for receiving the
accounting request and returning a response to the client
indicating that it has successfully received the request.
The RADIUS accounting server can act as a proxy client to
other kinds of accounting servers.
Network Security
Transactions between the client and RADIUS accounting server
are authenticated through the use of a shared secret, which is
never sent over the network.
Extensible Protocol
All transactions are comprised of variable length Attribute-
Length-Value 3-tuples. New attribute values can be added
without disturbing existing implementations of the protocol.
1.1. Specification of Requirements
The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
"SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this
document are to be interpreted as described in RFC 2119 [3]. These
key words mean the same thing whether capitalized or not.
1.2. Terminology
This document uses the following terms:
service The NAS provides a service to the dial-in user, such as PPP
or Telnet.
session Each service provided by the NAS to a dial-in user
constitutes a session, with the beginning of the session
defined as the point where service is first provided and
the end of the session defined as the point where service
is ended. A user may have multiple sessions in parallel or
series if the NAS supports that, with each session
generating a separate start and stop accounting record with
its own Acct-Session-Id.
silently discard
This means the implementation discards the packet without
further processing. The implementation SHOULD provide the
capability of logging the error, including the contents of
the silently discarded packet, and SHOULD record the event
in a statistics counter.
2. Operation
When a client is configured to use RADIUS Accounting, at the start of
service delivery it will generate an Accounting Start packet
describing the type of service being delivered and the user it is
being delivered to, and will send that to the RADIUS Accounting
server, which will send back an acknowledgement that the packet has
been received. At the end of service delivery the client will
generate an Accounting Stop packet describing the type of service
that was delivered and optionally statistics such as elapsed time,
input and output octets, or input and output packets. It will send
that to the RADIUS Accounting server, which will send back an
acknowledgement that the packet has been received.
The Accounting-Request (whether for Start or Stop) is submitted to
the RADIUS accounting server via the network. It is recommended that
the client continue attempting to send the Accounting-Request packet
until it receives an acknowledgement, using some form of backoff. If
no response is returned within a length of time, the request is re-
sent a number of times. The client can also forward requests to an
alternate server or servers in the event that the primary server is
down or unreachable. An alternate server can be used either after a
number of tries to the primary server fail, or in a round-robin
fashion. Retry and fallback algorithms are the topic of current
research and are not specified in detail in this document.
The RADIUS accounting server MAY make requests of other servers in
order to satisfy the request, in which case it acts as a client.
If the RADIUS accounting server is unable to successfully record the
accounting packet it MUST NOT send an Accounting-Response
acknowledgment to the client.
2.1. Proxy
See the "RADIUS" RFC [2] for information on Proxy RADIUS. Proxy
Accounting RADIUS works the same way, as illustrated by the following
example.
1. The NAS sends an accounting-request to the forwarding server.
2. The forwarding server logs the accounting-request (if desired),
adds its Proxy-State (if desired) after any other Proxy-State
attributes, updates the Request Authenticator, and forwards the
request to the remote server.
3. The remote server logs the accounting-request (if desired),
copies all Proxy-State attributes in order and unmodified from
the request to the response packet, and sends the accounting-
response to the forwarding server.
4. The forwarding server strips the last Proxy-State (if it added
one in step 2), updates the Response Authenticator and sends
the accounting-response to the NAS.
A forwarding server MUST not modify existing Proxy-State or Class
attributes present in the packet.
A forwarding server may either perform its forwarding function in a
pass through manner, where it sends retransmissions on as soon as it
gets them, or it may take responsibility for retransmissions, for
example in cases where the network link between forwarding and remote
server has very different characteristics than the link between NAS
and forwarding server.
Extreme care should be used when implementing a proxy server that
takes responsibility for retransmissions so that its retransmission
policy is robust and scalable.
3. Packet Format
Exactly one RADIUS Accounting packet is encapsulated in the UDP Data
field [4], where the UDP Destination Port field indicates 1813
(decimal).
When a reply is generated, the source and destination ports are
reversed.
EID 3896 (Verified) is as follows:Section: 3
Original Text:
This memo documents the RADIUS Accounting protocol. The early
deployment of RADIUS Accounting was done using UDP port number 1646,
which conflicts with the "sa-msg-port" service. The officially
assigned port number for RADIUS Accounting is 1813.
Corrected Text:
None
Notes:
The whole 3rd paragraph of section 3 is a duplicate of "Implementation Note" section and is barely related to packet format description.
A summary of the RADIUS data format is shown below. The fields are
transmitted from left to right.
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Code | Identifier | Length |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| |
| Authenticator |
| |
| |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Attributes ...
+-+-+-+-+-+-+-+-+-+-+-+-+-
Code
The Code field is one octet, and identifies the type of RADIUS
packet. When a packet is received with an invalid Code field, it
is silently discarded.
RADIUS Accounting Codes (decimal) are assigned as follows:
4 Accounting-Request
5 Accounting-Response
Identifier
The Identifier field is one octet, and aids in matching requests
and replies. The RADIUS server can detect a duplicate request if
it has the same client source IP address and source UDP port and
Identifier within a short span of time.
Length
The Length field is two octets. It indicates the length of the
packet including the Code, Identifier, Length, Authenticator and
Attribute fields. Octets outside the range of the Length field
MUST be treated as padding and ignored on reception. If the
packet is shorter than the Length field indicates, it MUST be
silently discarded. The minimum length is 20 and maximum length
is 4095.
Authenticator
The Authenticator field is sixteen (16) octets. The most
significant octet is transmitted first. This value is used to
authenticate the messages between the client and RADIUS accounting
server.
Request Authenticator
In Accounting-Request Packets, the Authenticator value is a 16
octet MD5 [5] checksum, called the Request Authenticator.
The NAS and RADIUS accounting server share a secret. The Request
Authenticator field in Accounting-Request packets contains a one-
way MD5 hash calculated over a stream of octets consisting of the
Code + Identifier + Length + 16 zero octets + request attributes +
shared secret (where + indicates concatenation). The 16 octet MD5
hash value is stored in the Authenticator field of the
Accounting-Request packet.
Note that the Request Authenticator of an Accounting-Request can
not be done the same way as the Request Authenticator of a RADIUS
Access-Request, because there is no User-Password attribute in an
Accounting-Request.
Response Authenticator
The Authenticator field in an Accounting-Response packet is called
the Response Authenticator, and contains a one-way MD5 hash
calculated over a stream of octets consisting of the Accounting-
Response Code, Identifier, Length, the Request Authenticator field
from the Accounting-Request packet being replied to, and the
response attributes if any, followed by the shared secret. The
resulting 16 octet MD5 hash value is stored in the Authenticator
field of the Accounting-Response packet.
Attributes
Attributes may have multiple instances, in such a case the order
of attributes of the same type SHOULD be preserved. The order of
attributes of different types is not required to be preserved.
4. Packet Types
The RADIUS packet type is determined by the Code field in the first
octet of the packet.
4.1. Accounting-Request
Description
Accounting-Request packets are sent from a client (typically a
Network Access Server or its proxy) to a RADIUS accounting server,
and convey information used to provide accounting for a service
provided to a user. The client transmits a RADIUS packet with the
Code field set to 4 (Accounting-Request).
Upon receipt of an Accounting-Request, the server MUST transmit an
Accounting-Response reply if it successfully records the
accounting packet, and MUST NOT transmit any reply if it fails to
record the accounting packet.
Any attribute valid in a RADIUS Access-Request or Access-Accept
packet is valid in a RADIUS Accounting-Request packet, except that
the following attributes MUST NOT be present in an Accounting-
Request: User-Password, CHAP-Password, Reply-Message, State.
Either NAS-IP-Address or NAS-Identifier MUST be present in a
RADIUS Accounting-Request. It SHOULD contain a NAS-Port or NAS-
Port-Type attribute or both unless the service does not involve a
port or the NAS does not distinguish among its ports.
If the Accounting-Request packet includes a Framed-IP-Address,
that attribute MUST contain the IP address of the user. If the
Access-Accept used the special values for Framed-IP-Address
telling the NAS to assign or negotiate an IP address for the user,
the Framed-IP-Address (if any) in the Accounting-Request MUST
contain the actual IP address assigned or negotiated.
A summary of the Accounting-Request packet format is shown below.
The fields are transmitted from left to right.
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Code | Identifier | Length |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| |
| Request Authenticator |
| |
| |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Attributes ...
+-+-+-+-+-+-+-+-+-+-+-+-+-
Code
4 for Accounting-Request.
Identifier
The Identifier field MUST be changed whenever the content of the
Attributes field changes, and whenever a valid reply has been
received for a previous request. For retransmissions where the
contents are identical, the Identifier MUST remain unchanged.
Note that if Acct-Delay-Time is included in the attributes of an
Accounting-Request then the Acct-Delay-Time value will be updated
when the packet is retransmitted, changing the content of the
Attributes field and requiring a new Identifier and Request
Authenticator.
Request Authenticator
The Request Authenticator of an Accounting-Request contains a 16-octet
MD5 hash value calculated according to the method described in
"Request Authenticator" above.
Attributes
The Attributes field is variable in length, and contains a list of
Attributes.
4.2. Accounting-Response
Description
Accounting-Response packets are sent by the RADIUS accounting
server to the client to acknowledge that the Accounting-Request
has been received and recorded successfully. If the Accounting-
Request was recorded successfully then the RADIUS accounting
server MUST transmit a packet with the Code field set to 5
(Accounting-Response). On reception of an Accounting-Response by
the client, the Identifier field is matched with a pending
Accounting-Request. The Response Authenticator field MUST contain
the correct response for the pending Accounting-Request. Invalid
packets are silently discarded.
A RADIUS Accounting-Response is not required to have any
attributes in it.
A summary of the Accounting-Response packet format is shown below.
The fields are transmitted from left to right.
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Code | Identifier | Length |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| |
| Response Authenticator |
| |
| |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Attributes ...
+-+-+-+-+-+-+-+-+-+-+-+-+-
Code
5 for Accounting-Response.
Identifier
The Identifier field is a copy of the Identifier field of the
Accounting-Request which caused this Accounting-Response.
Response Authenticator
The Response Authenticator of an Accounting-Response contains a
16-octet MD5 hash value calculated according to the method
described in "Response Authenticator" above.
Attributes
The Attributes field is variable in length, and contains a list of
zero or more Attributes.
5. Attributes
RADIUS Attributes carry the specific authentication, authorization
and accounting details for the request and response.
Some attributes MAY be included more than once. The effect of this
is attribute specific, and is specified in each attribute
description.
The end of the list of attributes is indicated by the Length of the
RADIUS packet.
A summary of the attribute format is shown below. The fields are
transmitted from left to right.
0 1 2
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Type | Length | Value ...
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Type
The Type field is one octet. Up-to-date values of the RADIUS Type
field are specified in the most recent "Assigned Numbers" RFC [6].
Values 192-223 are reserved for experimental use, values 224-240
are reserved for implementation-specific use, and values 241-255
are reserved and should not be used. This specification concerns
the following values:
1-39 (refer to RADIUS document [2])
40 Acct-Status-Type
41 Acct-Delay-Time
42 Acct-Input-Octets
43 Acct-Output-Octets
44 Acct-Session-Id
45 Acct-Authentic
46 Acct-Session-Time
47 Acct-Input-Packets
48 Acct-Output-Packets
49 Acct-Terminate-Cause
50 Acct-Multi-Session-Id
51 Acct-Link-Count
60+ (refer to RADIUS document [2])
Length
The Length field is one octet, and indicates the length of this
attribute including the Type, Length and Value fields. If an
attribute is received in an Accounting-Request with an invalid
Length, the entire request MUST be silently discarded.
Value
The Value field is zero or more octets and contains information
specific to the attribute. The format and length of the Value
field is determined by the Type and Length fields.
Note that none of the types in RADIUS terminate with a NUL (hex
00). In particular, types "text" and "string" in RADIUS do not
terminate with a NUL (hex 00). The Attribute has a length field
and does not use a terminator. Text contains UTF-8 encoded 10646
[7] characters and String contains 8-bit binary data. Servers and
clients MUST be able to deal with embedded nulls.
EID 2713 (Verified) is as follows:Section: 5
Original Text:
[7] characters and String contains 8-bit binary data. Servers and
servers and clients MUST be able to deal with embedded nulls.
^^^^^^^^^^
Corrected Text:
[7] characters and String contains 8-bit binary data. Servers and
clients MUST be able to deal with embedded nulls.
Notes:
Same as RFC 2865 , extraneous "servers and" can be deleted. ;)
RADIUS implementers using C are cautioned not to use strcpy() when
handling strings.
The format of the value field is one of five data types. Note
that type "text" is a subset of type "string."
text 1-253 octets containing UTF-8 encoded 10646 [7]
characters. Text of length zero (0) MUST NOT be sent;
omit the entire attribute instead.
string 1-253 octets containing binary data (values 0 through 255
decimal, inclusive). Strings of length zero (0) MUST NOT
be sent; omit the entire attribute instead.
address 32 bit value, most significant octet first.
integer 32 bit unsigned value, most significant octet first.
time 32 bit unsigned value, most significant octet first --
seconds since 00:00:00 UTC, January 1, 1970. The
standard Attributes do not use this data type but it is
presented here for possible use in future attributes.
5.1. Acct-Status-Type
Description
This attribute indicates whether this Accounting-Request marks the
beginning of the user service (Start) or the end (Stop).
It MAY be used by the client to mark the start of accounting for the
NAS (for example, upon booting) by specifying Accounting-On
and to mark the end of accounting for the NAS (for example, just
before a scheduled reboot) by specifying Accounting-Off.
EID 4485 (Verified) is as follows:Section: 5.1
Original Text:
This attribute indicates whether this Accounting-Request marks the
beginning of the user service (Start) or the end (Stop).
It MAY be used by the client to mark the start of accounting (for
example, upon booting) by specifying Accounting-On and to mark the
end of accounting (for example, just before a scheduled reboot) by
specifying Accounting-Off.
Corrected Text:
This attribute indicates whether this Accounting-Request marks the
beginning of the user service (Start) or the end (Stop).
It MAY be used by the client to mark the start of accounting for the
NAS (for example, upon booting) by specifying Accounting-On
and to mark the end of accounting for the NAS (for example, just
before a scheduled reboot) by specifying Accounting-Off.
Notes:
Some RADIUS client implementations send scoped Accounting-On and Accounting-Off Accounting-Request packets. This is seen, for example, with some wireless APs that include a Called-Station-Id attribute to scope to a Basic Service Set (BSS).
This is an incorrect interpretation of the RFC that is not backwards compatible with consumers of RADIUS accounting information, yet the RFC is ambiguous on this point.
The RFC must be clear that Accounting-On and Accounting-Off apply to the whole NAS and cannot be scoped in this manner.
New Acct-Status-Type values must instead be defined to allow this, perhaps named something like Scoped-Accounting-On and Scoped-Accounting-Off.
A summary of the Acct-Status-Type attribute format is shown below.
The fields are transmitted from left to right.
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Type | Length | Value
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Value (cont) |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Type
40 for Acct-Status-Type.
Length
6. IANA Considerations
The Packet Type Codes, Attribute Types, and Attribute Values defined
in this document are registered by the Internet Assigned Numbers
Authority (IANA) from the RADIUS name spaces as described in the
"IANA Considerations" section of RFC 2865 [2], in accordance with BCP
26 [8].
5.2. Acct-Delay-Time
Description
This attribute indicates how many seconds the client has been
trying to send this record for, and can be subtracted from the
time of arrival on the server to find the approximate time of the
event generating this Accounting-Request. (Network transit time
is ignored.)
Note that changing the Acct-Delay-Time causes the Identifier to
change; see the discussion under Identifier above.
A summary of the Acct-Delay-Time attribute format is shown below.
The fields are transmitted from left to right.
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Type | Length | Value
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Value (cont) |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Type
41 for Acct-Delay-Time.
Length
6. IANA Considerations
The Packet Type Codes, Attribute Types, and Attribute Values defined
in this document are registered by the Internet Assigned Numbers
Authority (IANA) from the RADIUS name spaces as described in the
"IANA Considerations" section of RFC 2865 [2], in accordance with BCP
26 [8].
5.3. Acct-Input-Octets
Description
This attribute indicates how many octets have been received from
the port over the course of this service being provided, and can
only be present in Accounting-Request records where the Acct-
Status-Type is set to Stop.
A summary of the Acct-Input-Octets attribute format is shown below.
The fields are transmitted from left to right.
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Type | Length | Value
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Value (cont) |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Type
42 for Acct-Input-Octets.
Length
6. IANA Considerations
The Packet Type Codes, Attribute Types, and Attribute Values defined
in this document are registered by the Internet Assigned Numbers
Authority (IANA) from the RADIUS name spaces as described in the
"IANA Considerations" section of RFC 2865 [2], in accordance with BCP
26 [8].
5.4. Acct-Output-Octets
Description
This attribute indicates how many octets have been sent to the
port in the course of delivering this service, and can only be
present in Accounting-Request records where the Acct-Status-Type
is set to Stop.
A summary of the Acct-Output-Octets attribute format is shown below.
The fields are transmitted from left to right.
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Type | Length | Value
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Value (cont) |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Type
43 for Acct-Output-Octets.
Length
6. IANA Considerations
The Packet Type Codes, Attribute Types, and Attribute Values defined
in this document are registered by the Internet Assigned Numbers
Authority (IANA) from the RADIUS name spaces as described in the
"IANA Considerations" section of RFC 2865 [2], in accordance with BCP
26 [8].
5.5. Acct-Session-Id
Description
This attribute is a unique Accounting ID to make it easy to match
start and stop records in a log file. The start and stop records
for a given session MUST have the same Acct-Session-Id. An
Accounting-Request packet MUST have an Acct-Session-Id. An
Access-Request packet MAY have an Acct-Session-Id; if it does,
then the NAS MUST use the same Acct-Session-Id in the Accounting-
Request packets for that session.
The Acct-Session-Id SHOULD contain UTF-8 encoded 10646 [7]
characters.
For example, one implementation uses a string with an 8-digit
upper case hexadecimal number, the first two digits increment on
each reboot (wrapping every 256 reboots) and the next 6 digits
counting from 0 for the first person logging in after a reboot up
to 2^24-1, about 16 million. Other encodings are possible.
A summary of the Acct-Session-Id attribute format is shown below.
The fields are transmitted from left to right.
0 1 2
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Type | Length | Text ...
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Type
44 for Acct-Session-Id.
Length
>= 3
String
The String field SHOULD be a string of UTF-8 encoded 10646 [7]
characters.
5.6. Acct-Authentic
Description
This attribute MAY be included in an Accounting-Request to
indicate how the user was authenticated, whether by RADIUS, the
NAS itself, or another remote authentication protocol. Users who
are delivered service without being authenticated SHOULD NOT
generate Accounting records.
A summary of the Acct-Authentic attribute format is shown below. The
fields are transmitted from left to right.
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Type | Length | Value
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Value (cont) |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Type
45 for Acct-Authentic.
Length
6. IANA Considerations
The Packet Type Codes, Attribute Types, and Attribute Values defined
in this document are registered by the Internet Assigned Numbers
Authority (IANA) from the RADIUS name spaces as described in the
"IANA Considerations" section of RFC 2865 [2], in accordance with BCP
26 [8].
5.7. Acct-Session-Time
Description
This attribute indicates how many seconds the user has received
service for, and can only be present in Accounting-Request records
where the Acct-Status-Type is set to Stop.
A summary of the Acct-Session-Time attribute format is shown below.
The fields are transmitted from left to right.
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Type | Length | Value
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Value (cont) |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Type
46 for Acct-Session-Time.
Length
6. IANA Considerations
The Packet Type Codes, Attribute Types, and Attribute Values defined
in this document are registered by the Internet Assigned Numbers
Authority (IANA) from the RADIUS name spaces as described in the
"IANA Considerations" section of RFC 2865 [2], in accordance with BCP
26 [8].
5.8. Acct-Input-Packets
Description
This attribute indicates how many packets have been received from
the port over the course of this service being provided to a
Framed User, and can only be present in Accounting-Request records
where the Acct-Status-Type is set to Stop.
A summary of the Acct-Input-packets attribute format is shown below.
The fields are transmitted from left to right.
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Type | Length | Value
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Value (cont) |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Type
47 for Acct-Input-Packets.
Length
6. IANA Considerations
The Packet Type Codes, Attribute Types, and Attribute Values defined
in this document are registered by the Internet Assigned Numbers
Authority (IANA) from the RADIUS name spaces as described in the
"IANA Considerations" section of RFC 2865 [2], in accordance with BCP
26 [8].
5.9. Acct-Output-Packets
Description
This attribute indicates how many packets have been sent to the
port in the course of delivering this service to a Framed User,
and can only be present in Accounting-Request records where the
Acct-Status-Type is set to Stop.
A summary of the Acct-Output-Packets attribute format is shown below.
The fields are transmitted from left to right.
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Type | Length | Value
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Value (cont) |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Type
48 for Acct-Output-Packets.
Length
6. IANA Considerations
The Packet Type Codes, Attribute Types, and Attribute Values defined
in this document are registered by the Internet Assigned Numbers
Authority (IANA) from the RADIUS name spaces as described in the
"IANA Considerations" section of RFC 2865 [2], in accordance with BCP
26 [8].
5.10. Acct-Terminate-Cause
Description
This attribute indicates how the session was terminated, and can
only be present in Accounting-Request records where the Acct-
Status-Type is set to Stop.
A summary of the Acct-Terminate-Cause attribute format is shown
below. The fields are transmitted from left to right.
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Type | Length | Value
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Value (cont) |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Type
49 for Acct-Terminate-Cause
Length
6. IANA Considerations
The Packet Type Codes, Attribute Types, and Attribute Values defined
in this document are registered by the Internet Assigned Numbers
Authority (IANA) from the RADIUS name spaces as described in the
"IANA Considerations" section of RFC 2865 [2], in accordance with BCP
26 [8].
5.11. Acct-Multi-Session-Id
Description
This attribute is a unique Accounting ID to make it easy to link
together multiple related sessions in a log file. Each session
linked together would have a unique Acct-Session-Id but the same
Acct-Multi-Session-Id. It is strongly recommended that the Acct-
Multi-Session-Id contain UTF-8 encoded 10646 [7] characters.
A summary of the Acct-Session-Id attribute format is shown below.
The fields are transmitted from left to right.
0 1 2
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Type | Length | String ...
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Type
50 for Acct-Multi-Session-Id.
Length
>= 3
String
The String field SHOULD contain UTF-8 encoded 10646 [7] characters.
5.12. Acct-Link-Count
Description
This attribute gives the count of links which are known to have been
in a given multilink session at the time the accounting record is
generated. The NAS MAY include the Acct-Link-Count attribute in any
Accounting-Request which might have multiple links.
A summary of the Acct-Link-Count attribute format is show below. The
fields are transmitted from left to right.
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Type | Length | Value
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Value (cont) |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Type
51 for Acct-Link-Count.
Length
6. IANA Considerations
The Packet Type Codes, Attribute Types, and Attribute Values defined
in this document are registered by the Internet Assigned Numbers
Authority (IANA) from the RADIUS name spaces as described in the
"IANA Considerations" section of RFC 2865 [2], in accordance with BCP
26 [8].
5.13. Table of Attributes
The following table provides a guide to which attributes may be found
in Accounting-Request packets. No attributes should be found in
Accounting-Response packets except Proxy-State and possibly Vendor-
Specific.
# Attribute
0-1 User-Name
0 User-Password
0 CHAP-Password
0-1 NAS-IP-Address [Note 1]
0-1 NAS-Port
0-1 Service-Type
0-1 Framed-Protocol
0-1 Framed-IP-Address
0-1 Framed-IP-Netmask
0-1 Framed-Routing
0+ Filter-Id
0-1 Framed-MTU
0+ Framed-Compression
0+ Login-IP-Host
0-1 Login-Service
0-1 Login-TCP-Port
0 Reply-Message
0-1 Callback-Number
0-1 Callback-Id
0+ Framed-Route
0-1 Framed-IPX-Network
0 State
0+ Class
0+ Vendor-Specific
0-1 Session-Timeout
0-1 Idle-Timeout
0-1 Termination-Action
0-1 Called-Station-Id
0-1 Calling-Station-Id
0-1 NAS-Identifier [Note 1]
0+ Proxy-State
0-1 Login-LAT-Service
0-1 Login-LAT-Node
0-1 Login-LAT-Group
0-1 Framed-AppleTalk-Link
0-1 Framed-AppleTalk-Network
0-1 Framed-AppleTalk-Zone
1 Acct-Status-Type
0-1 Acct-Delay-Time
0-1 Acct-Input-Octets
0-1 Acct-Output-Octets
1 Acct-Session-Id
0-1 Acct-Authentic
0-1 Acct-Session-Time
0-1 Acct-Input-Packets
0-1 Acct-Output-Packets
0-1 Acct-Terminate-Cause
0+ Acct-Multi-Session-Id
0+ Acct-Link-Count
0 CHAP-Challenge
0-1 NAS-Port-Type
0-1 Port-Limit
0-1 Login-LAT-Port
[Note 1] An Accounting-Request MUST contain either a NAS-IP-Address
or a NAS-Identifier (or both).
The following table defines the above table entries.
0 This attribute MUST NOT be present
0+ Zero or more instances of this attribute MAY be present.
0-1 Zero or one instance of this attribute MAY be present.
1 Exactly one instance of this attribute MUST be present.
6. IANA Considerations
The Packet Type Codes, Attribute Types, and Attribute Values defined
in this document are registered by the Internet Assigned Numbers
Authority (IANA) from the RADIUS name spaces as described in the
"IANA Considerations" section of RFC 2865 [2], in accordance with BCP
26 [8].
7. Security Considerations
Security issues are discussed in sections concerning the
authenticator included in accounting requests and responses, using a
shared secret which is never sent over the network.
8. Change Log
US-ASCII replaced by UTF-8.
Added notes on Proxy.
Framed-IP-Address should contain the actual IP address of the user.
If Acct-Session-ID was sent in an access-request, it must be used in
the accounting-request for that session.
New values added to Acct-Status-Type.
Added an IANA Considerations section.
Updated references.
Text strings identified as a subset of string, to clarify use of
UTF-8.
9. References
[1] Rigney, C., "RADIUS Accounting", RFC 2139, April 1997.
[2] Rigney, C., Willens, S., Rubens, A. and W. Simpson, "Remote
Authentication Dial In User Service (RADIUS)", RFC 2865, June
2000.
[3] Bradner, S., "Key words for use in RFCs to Indicate Requirement
Levels", BCP 14, RFC 2119, March, 1997.
[4] Postel, J., "User Datagram Protocol", STD 6, RFC 768, August
1980.
[5] Rivest, R. and S. Dusse, "The MD5 Message-Digest Algorithm", RFC
1321, April 1992.
[6] Reynolds, J. and J. Postel, "Assigned Numbers", STD 2, RFC 1700,
October 1994.
[7] Yergeau, F., "UTF-8, a transformation format of ISO 10646", RFC
2279, January 1998.
[8] Alvestrand, H. and T. Narten, "Guidelines for Writing an IANA
Considerations Section in RFCs", BCP 26, RFC 2434, October 1998.
10. Acknowledgements
RADIUS and RADIUS Accounting were originally developed by Steve
Willens of Livingston Enterprises for their PortMaster series of
Network Access Servers.
11. Chair's Address
The RADIUS working group can be contacted via the current chair:
Carl Rigney
Livingston Enterprises
4464 Willow Road
Pleasanton, California 94588
Phone: +1 925 737 2100
EMail: cdr@telemancy.com
12. Author's Address
Questions about this memo can also be directed to:
Carl Rigney
Livingston Enterprises
4464 Willow Road
Pleasanton, California 94588
EMail: cdr@telemancy.com
13. Full Copyright Statement
Copyright (C) The Internet Society (2000). All Rights Reserved.
This document and translations of it may be copied and furnished to
others, and derivative works that comment on or otherwise explain it
or assist in its implementation may be prepared, copied, published
and distributed, in whole or in part, without restriction of any
kind, provided that the above copyright notice and this paragraph are
included on all such copies and derivative works. However, this
document itself may not be modified in any way, such as by removing
the copyright notice or references to the Internet Society or other
Internet organizations, except as needed for the purpose of
developing Internet standards in which case the procedures for
copyrights defined in the Internet Standards process must be
followed, or as required to translate it into languages other than
English.
The limited permissions granted above are perpetual and will not be
revoked by the Internet Society or its successors or assigns.
This document and the information contained herein is provided on an
"AS IS" basis and THE INTERNET SOCIETY AND THE INTERNET ENGINEERING
TASK FORCE DISCLAIMS ALL WARRANTIES, EXPRESS OR IMPLIED, INCLUDING
BUT NOT LIMITED TO ANY WARRANTY THAT THE USE OF THE INFORMATION
HEREIN WILL NOT INFRINGE ANY RIGHTS OR ANY IMPLIED WARRANTIES OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.
Acknowledgement
Funding for the RFC Editor function is currently provided by the
Internet Society.