Network Working Group                                      F. Kastenholz
Request for Comments: 1398                            FTP Software, Inc.
Obsoletes: 1284                                             January 1993


                   Definitions of Managed Objects for
                   the Ethernet-like Interface Types

Status of this Memo

   This RFC specifies an IAB standards track protocol for the Internet
   community, and requests discussion and suggestions for improvements.
   Please refer to the current edition of the "IAB Official Protocol
   Standards" for the standardization state and status of this protocol.
   Distribution of this memo is unlimited.

Abstract

   This memo defines a portion of the Management Information Base (MIB)
   for use with network management protocols in TCP/IP-based internets.
   In particular, it defines objects for managing ethernet-like objects.

Table of Contents

   1. The Network Management Framework ......................    1
   2. Objects ...............................................    2
   2.1 Format of Definitions ................................    2
   3. Overview ..............................................    3
   4. Definitions ...........................................    4
   4.1 The Ethernet-like Statistics Group ...................    4
   4.2 The Ethernet-like Collision Statistics Group .........   11
   4.3 802.3 Tests ..........................................   12
   4.4 802.3 Hardware Chipsets ..............................   14
   5. Change Log ............................................   14
   6. Acknowledgements ......................................   16
   7. References ............................................   16
   8. Security Considerations ...............................   17
   9. Author's Address ......................................   17

1.  The Network Management Framework

   The Internet-standard Network Management Framework consists of three
   components.  They are:

      STD 16/RFC 1155 [3] which defines the SMI, the mechanisms used for
      describing and naming objects for the purpose of management.  STD
      16/RFC 1212 [13] defines a more concise description mechanism,
      which is wholly consistent with the SMI.



Kastenholz                                                      [Page 1]


RFC 1398                   Ethernet-Like MIB                January 1993


      RFC 1156 [4] which defines MIB-I, the core set of managed objects
      for the Internet suite of protocols.  STD 17/RFC 1213 [6] defines
      MIB-II, an evolution of MIB-I based on implementation experience
      and new operational requirements.

      STD 15/RFC 1157 [5] which defines the SNMP, the protocol used for
      network access to managed objects.

   The Framework permits new objects to be defined for the purpose of
   experimentation and evaluation.

2.  Objects

   Managed objects are accessed via a virtual information store, termed
   the Management Information Base or MIB.  Objects in the MIB are
   defined using the subset of Abstract Syntax Notation One (ASN.1) [7]
   defined in the SMI.  In particular, each object has a name, a syntax,
   and an encoding.  The name is an object identifier, an
   administratively assigned name, which specifies an object type.  The
   object type together with an object instance serves to uniquely
   identify a specific instantiation of the object.  For human
   convenience, we often use a textual string, termed the OBJECT
   DESCRIPTOR, to also refer to the object type.

   The syntax of an object type defines the abstract data structure
   corresponding to that object type.  The ASN.1 language is used for
   this purpose.  However, the SMI [3] purposely restricts the ASN.1
   constructs which may be used.  These restrictions are explicitly made
   for simplicity.

   The encoding of an object type is simply how that object type is
   represented using the object type's syntax.  Implicitly tied to the
   notion of an object type's syntax and encoding is how the object type
   is represented when being transmitted on the network.

   The SMI specifies the use of the basic encoding rules of ASN.1 [8],
   subject to the additional requirements imposed by the SNMP.

2.1.  Format of Definitions

   Section 4 contains contains the specification of all object types
   contained in this MIB module.  The object types are defined using the
   conventions defined in the SMI, as amended by the extensions
   specified in [13].







Kastenholz                                                      [Page 2]


RFC 1398                   Ethernet-Like MIB                January 1993


3.  Overview

   Instances of these object types represent attributes of an interface
   to an ethernet-like communications medium.  At present, ethernet-like
   media are identified by three values of the ifType object in the
   Internet-standard MIB:

          ethernet-csmacd(6)
          iso88023-csmacd(7)
          starLan(11)

   For these interfaces, the value of the ifSpecific variable in the
   MIB-II [6] has the OBJECT IDENTIFIER value:

          dot3    OBJECT IDENTIFER ::= { transmission 7 }

   The definitions presented here are based on the IEEE 802.3 Layer
   Management Specification [9], as originally interpreted by Frank
   Kastenholz of Interlan in [10].  Implementors of these MIB objects
   should note that the IEEE document explicitly describes (in the form
   of Pascal pseudocode) when, where, and how various MAC attributes are
   measured.  The IEEE document also describes the effects of MAC
   actions that may be invoked by manipulating instances of the MIB
   objects defined here.

   To the extent that some of the attributes defined in [9] are
   represented by previously defined objects in the Internet- standard
   MIB or in the Generic Interface Extensions MIB [11], such attributes
   are not redundantly represented by objects defined in this memo.
   Among the attributes represented by objects defined in other memos
   are the number of octets transmitted or received on a particular
   interface, the number of frames transmitted or received on a
   particular interface, the promiscuous status of an interface, the MAC
   address of an interface, and multicast information associated with an
   interface.

   The relationship between an ethernet-like interface and an interface
   in the context of the Internet-standard MIB is one-to-one.  As such,
   the value of an ifIndex object instance can be directly used to
   identify corresponding instances of the objects defined herein.











Kastenholz                                                      [Page 3]


RFC 1398                   Ethernet-Like MIB                January 1993


4.  Definitions

          RFC1398-MIB DEFINITIONS ::= BEGIN


               IMPORTS
                    Counter, Gauge
                         FROM RFC1155-SMI
                    transmission
                         FROM RFC1213-MIB
                    OBJECT-TYPE
                         FROM RFC-1212;

          --  This MIB module uses the extended OBJECT-TYPE macro as
          --  defined in RFC-1212.

          --  this is the MIB module for ethernet-like objects

          dot3    OBJECT IDENTIFIER ::= { transmission 7 }

          -- { dot3 1 } is obsolete and has been deleted.

4.1.  The Ethernet-like Statistics Group


          -- the Ethernet-like Statistics group

          -- Implementation of this group is mandatory

          dot3StatsTable   OBJECT-TYPE
               SYNTAX    SEQUENCE OF Dot3StatsEntry
               ACCESS    not-accessible
               STATUS    mandatory
               DESCRIPTION
                         "Statistics for a collection of ethernet-like
                         interfaces attached to a particular system."
               ::= { dot3 2 }


          dot3StatsEntry   OBJECT-TYPE
               SYNTAX    Dot3StatsEntry
               ACCESS    not-accessible
               STATUS    mandatory
               DESCRIPTION
                         "Statistics for a particular interface to an
                         ethernet-like medium."
               INDEX     { dot3StatsIndex }
               ::= { dot3StatsTable 1 }



Kastenholz                                                      [Page 4]


RFC 1398                   Ethernet-Like MIB                January 1993


          Dot3StatsEntry ::= SEQUENCE {
               dot3StatsIndex
                    INTEGER,
               dot3StatsAlignmentErrors
                    Counter,
               dot3StatsFCSErrors
                    Counter,
               dot3StatsSingleCollisionFrames
                    Counter,
               dot3StatsMultipleCollisionFrames
                    Counter,
               dot3StatsSQETestErrors
                    Counter,
               dot3StatsDeferredTransmissions
                    Counter,
               dot3StatsLateCollisions
                    Counter,
               dot3StatsExcessiveCollisions
                    Counter,
               dot3StatsInternalMacTransmitErrors
                    Counter,
               dot3StatsCarrierSenseErrors
                    Counter,
               dot3StatsFrameTooLongs
                    Counter,
               dot3StatsInternalMacReceiveErrors
                    Counter
          }

          dot3StatsIndex   OBJECT-TYPE
               SYNTAX    INTEGER
               ACCESS    read-only
               STATUS    mandatory
               DESCRIPTION
                         "An index value that uniquely identifies an
                         interface to an ethernet-like medium.  The
                         interface identified by a particular value of
                         this index is the same interface as identified
                         by the same value of ifIndex."
               ::= { dot3StatsEntry 1 }


          dot3StatsAlignmentErrors   OBJECT-TYPE
               SYNTAX    Counter
               ACCESS    read-only
               STATUS    mandatory
               DESCRIPTION
                         "A count of frames received on a particular



Kastenholz                                                      [Page 5]


RFC 1398                   Ethernet-Like MIB                January 1993


                         interface that are not an integral number of
                         octets in length and do not pass the FCS check.

                         The count represented by an instance of this
                         object is incremented when the alignmentError
                         status is returned by the MAC service to the
                         LLC (or other MAC user). Received frames for
                         which multiple error conditions obtain are,
                         according to the conventions of IEEE 802.3
                         Layer Management, counted exclusively according
                         to the error status presented to the LLC."
               REFERENCE
                         "IEEE 802.3 Layer Management"
               ::= { dot3StatsEntry 2 }


          dot3StatsFCSErrors   OBJECT-TYPE
               SYNTAX    Counter
               ACCESS    read-only
               STATUS    mandatory
               DESCRIPTION
                         "A count of frames received on a particular
                         interface that are an integral number of octets
                         in length but do not pass the FCS check.

                         The count represented by an instance of this
                         object is incremented when the frameCheckError
                         status is returned by the MAC service to the
                         LLC (or other MAC user). Received frames for
                         which multiple error conditions obtain are,
                         according to the conventions of IEEE 802.3
                         Layer Management, counted exclusively according
                         to the error status presented to the LLC."
               REFERENCE
                         "IEEE 802.3 Layer Management"
               ::= { dot3StatsEntry 3 }


          dot3StatsSingleCollisionFrames   OBJECT-TYPE
               SYNTAX    Counter
               ACCESS    read-only
               STATUS    mandatory
               DESCRIPTION
                         "A count of successfully transmitted frames on
                         a particular interface for which transmission
                         is inhibited by exactly one collision.

                         A frame that is counted by an instance of this



Kastenholz                                                      [Page 6]


RFC 1398                   Ethernet-Like MIB                January 1993


                         object is also counted by the corresponding
                         instance of either the ifOutUcastPkts or
                         ifOutNUcastPkts object and is not counted by
                         the corresponding instance of the
                         dot3StatsMultipleCollisionFrames object."
               REFERENCE
                         "IEEE 802.3 Layer Management"
               ::= { dot3StatsEntry 4 }


          dot3StatsMultipleCollisionFrames   OBJECT-TYPE
               SYNTAX    Counter
               ACCESS    read-only
               STATUS    mandatory
               DESCRIPTION
                         "A count of successfully transmitted frames on
                         a particular interface for which transmission
                         is inhibited by more than one collision.

                         A frame that is counted by an instance of this
                         object is also counted by the corresponding
                         instance of either the ifOutUcastPkts or
                         ifOutNUcastPkts object and is not counted by
                         the corresponding instance of the
                         dot3StatsSingleCollisionFrames object."
               REFERENCE
                         "IEEE 802.3 Layer Management"
               ::= { dot3StatsEntry 5 }


          dot3StatsSQETestErrors   OBJECT-TYPE
               SYNTAX    Counter
               ACCESS    read-only
               STATUS    mandatory
               DESCRIPTION
                         "A count of times that the SQE TEST ERROR
                         message is generated by the PLS sublayer for a
                         particular interface. The SQE TEST ERROR
                         message is defined in section 7.2.2.2.4 of
                         ANSI/IEEE 802.3-1985 and its generation is
                         described in section 7.2.4.6 of the same
                         document."
               REFERENCE
                         "ANSI/IEEE Std 802.3-1985 Carrier Sense
                         Multiple Access with Collision Detection Access
                         Method and Physical Layer Specifications"
               ::= { dot3StatsEntry 6 }




Kastenholz                                                      [Page 7]


RFC 1398                   Ethernet-Like MIB                January 1993


          dot3StatsDeferredTransmissions   OBJECT-TYPE
               SYNTAX    Counter
               ACCESS    read-only
               STATUS    mandatory
               DESCRIPTION
                         "A count of frames for which the first
                         transmission attempt on a particular interface
                         is delayed because the medium is busy.

                         The count represented by an instance of this
                         object does not include frames involved in
                         collisions."
               REFERENCE
                         "IEEE 802.3 Layer Management"
               ::= { dot3StatsEntry 7 }


          dot3StatsLateCollisions   OBJECT-TYPE
               SYNTAX    Counter
               ACCESS    read-only
               STATUS    mandatory
               DESCRIPTION
                         "The number of times that a collision is
                         detected on a particular interface later than
                         512 bit-times into the transmission of a
                         packet.

                         Five hundred and twelve bit-times corresponds
                         to 51.2 microseconds on a 10 Mbit/s system. A
                         (late) collision included in a count
                         represented by an instance of this object is
                         also considered as a (generic) collision for
                         purposes of other collision-related
                         statistics."
               REFERENCE
                         "IEEE 802.3 Layer Management"
               ::= { dot3StatsEntry 8 }


          dot3StatsExcessiveCollisions   OBJECT-TYPE
               SYNTAX    Counter
               ACCESS    read-only
               STATUS    mandatory
               DESCRIPTION
                         "A count of frames for which transmission on a
                         particular interface fails due to excessive
                         collisions."




Kastenholz                                                      [Page 8]


RFC 1398                   Ethernet-Like MIB                January 1993


               REFERENCE
                         "IEEE 802.3 Layer Management"
               ::= { dot3StatsEntry 9 }


          dot3StatsInternalMacTransmitErrors   OBJECT-TYPE
               SYNTAX    Counter
               ACCESS    read-only
               STATUS    mandatory
               DESCRIPTION
                         "A count of frames for which transmission on a
                         particular interface fails due to an internal
                         MAC sublayer transmit error. A frame is only
                         counted by an instance of this object if it is
                         not counted by the corresponding instance of
                         either the dot3StatsLateCollisions object, the
                         dot3StatsExcessiveCollisions object, or the
                         dot3StatsCarrierSenseErrors object.

                         The precise meaning of the count represented by
                         an instance of this object is implementation-
                         specific.  In particular, an instance of this
                         object may represent a count of transmission
                         errors on a particular interface that are not
                         otherwise counted."
               REFERENCE
                         "IEEE 802.3 Layer Management"
               ::= { dot3StatsEntry 10 }


          dot3StatsCarrierSenseErrors   OBJECT-TYPE
               SYNTAX    Counter
               ACCESS    read-only
               STATUS    mandatory
               DESCRIPTION
                         "The number of times that the carrier sense
                         condition was lost or never asserted when
                         attempting to transmit a frame on a particular
                         interface.

                         The count represented by an instance of this
                         object is incremented at most once per
                         transmission attempt, even if the carrier sense
                         condition fluctuates during a transmission
                         attempt."
               REFERENCE
                         "IEEE 802.3 Layer Management"
               ::= { dot3StatsEntry 11 }



Kastenholz                                                      [Page 9]


RFC 1398                   Ethernet-Like MIB                January 1993


          -- { dot3StatsEntry 12 } is not assigned

          dot3StatsFrameTooLongs   OBJECT-TYPE
               SYNTAX    Counter
               ACCESS    read-only
               STATUS    mandatory
               DESCRIPTION
                         "A count of frames received on a particular
                         interface that exceed the maximum permitted
                         frame size.

                         The count represented by an instance of this
                         object is incremented when the frameTooLong
                         status is returned by the MAC service to the
                         LLC (or other MAC user). Received frames for
                         which multiple error conditions obtain are,
                         according to the conventions of IEEE 802.3
                         Layer Management, counted exclusively according
                         to the error status presented to the LLC."
               REFERENCE
                         "IEEE 802.3 Layer Management"
               ::= { dot3StatsEntry 13 }



          -- { dot3StatsEntry 14 } is not assigned


          -- { dot3StatsEntry 15 } is not assigned

          dot3StatsInternalMacReceiveErrors   OBJECT-TYPE
               SYNTAX    Counter
               ACCESS    read-only
               STATUS    mandatory
               DESCRIPTION
                         "A count of frames for which reception on a
                         particular interface fails due to an internal
                         MAC sublayer receive error. A frame is only
                         counted by an instance of this object if it is
                         not counted by the corresponding instance of
                         either the dot3StatsFrameTooLongs object, the
                         dot3StatsAlignmentErrors object, or the
                         dot3StatsFCSErrors object.

                         The precise meaning of the count represented by
                         an instance of this object is implementation-
                         specific.  In particular, an instance of this
                         object may represent a count of receive errors



Kastenholz                                                     [Page 10]


RFC 1398                   Ethernet-Like MIB                January 1993


                         on a particular interface that are not
                         otherwise counted."
               REFERENCE
                         "IEEE 802.3 Layer Management"
               ::= { dot3StatsEntry 16 }

4.2.  The Ethernet-like Collision Statistics Group


          -- the Ethernet-like Collision Statistics group

          -- Implementation of this group is optional; it is appropriate
          -- for all systems which have the necessary metering

          dot3CollTable   OBJECT-TYPE
               SYNTAX    SEQUENCE OF Dot3CollEntry
               ACCESS    not-accessible
               STATUS    mandatory
               DESCRIPTION
                         "A collection of collision histograms for a
                         particular set of interfaces."
               ::= { dot3 5 }


          dot3CollEntry   OBJECT-TYPE
               SYNTAX    Dot3CollEntry
               ACCESS    not-accessible
               STATUS    mandatory
               DESCRIPTION
                         "A cell in the histogram of per-frame
                         collisions for a particular interface.  An
                         instance of this object represents the
                         frequency of individual MAC frames for which
                         the transmission (successful or otherwise) on a
                         particular interface is accompanied by a
                         particular number of media collisions."
               INDEX     { dot3CollIndex, dot3CollCount }
               ::= { dot3CollTable 1 }



          Dot3CollEntry ::= SEQUENCE {
               dot3CollIndex
                    INTEGER,
               dot3CollCount
                    INTEGER,
               dot3CollFrequencies
                    Counter



Kastenholz                                                     [Page 11]


RFC 1398                   Ethernet-Like MIB                January 1993


          }


          dot3CollIndex   OBJECT-TYPE
               SYNTAX    INTEGER
               ACCESS    read-only
               STATUS    mandatory
               DESCRIPTION
                         "The index value that uniquely identifies the
                         interface to which a particular collision
                         histogram cell pertains.  The interface
                         identified by a particular value of this index
                         is the same interface as identified by the same
                         value of ifIndex."
               ::= { dot3CollEntry 1 }


          dot3CollCount   OBJECT-TYPE
               SYNTAX    INTEGER (1..16)
               ACCESS    read-only
               STATUS    mandatory
               DESCRIPTION
                         "The number of per-frame media collisions for
                         which a particular collision histogram cell
                         represents the frequency on a particular
                         interface."
               ::= { dot3CollEntry 2 }


          dot3CollFrequencies   OBJECT-TYPE
               SYNTAX    Counter
               ACCESS    read-only
               STATUS    mandatory
               DESCRIPTION
                         "A count of individual MAC frames for which the
                         transmission (successful or otherwise) on a
                         particular interface is accompanied by a
                         particular number of media collisions."
               ::= { dot3CollEntry 3 }


4.3.  802.3 Tests


      --  802.3 Tests

      -- The ifExtnsTestTable defined in RFC 1229 provides a common
      -- means for a manager to test any interface corresponding to



Kastenholz                                                     [Page 12]


RFC 1398                   Ethernet-Like MIB                January 1993


      -- a value of ifIndex.

      -- At this time, one well known test (testFullDuplexLoopBack) is
      -- defined in RFC 1229.  For ethernet-like interfaces, this test
      -- configures the MAC chip and executes an internal loopback
      -- test of memory and the MAC chip logic.  This loopback test can
      -- only be executed if the interface is offline.  Once the test
      -- has completed, the MAC chip should be reinitialized for network
      -- operation, but it should remain offline.

      -- If an error occurs during a test, the object ifExtnsTestResult
      -- (defined in RFC 1229) will be set to failed(7).  The following
      -- two OBJECT IDENTIFIERs may be used to provided more
      -- information as values for the object ifExtnsTestCode in
      -- RFC 1229:

          dot3Errors             OBJECT IDENTIFIER ::= { dot3 7 }

                               -- couldn't initialize MAC chip for test
          dot3ErrorInitError     OBJECT IDENTIFIER ::= { dot3Errors 1 }

                                -- expected data not received (or not
                                -- received correctly) in loopback test
          dot3ErrorLoopbackError OBJECT IDENTIFIER ::= { dot3Errors 2 }

       -- Tests
        --  TDR Test

       -- Another test, specific to ethernet-like interfaces with the
       -- exception of 10BaseT and 10BaseF, is Time-domain Reflectometry
           (TDR).
       -- The TDR value may be useful in determining the approximate
           distance
       -- to a cable fault.  It is advisable to repeat this test to
           check for
       -- a consistent resulting TDR value, to verify that there is a
          fault.

          dot3Tests   OBJECT IDENTIFIER ::= { dot3 6 }
          dot3TestTdr OBJECT IDENTIFIER ::= { dot3Tests 1 }

       -- A TDR test returns as its result the time interval, measured
       -- in 10 MHz ticks or 100 nsec units, between the start of
       -- TDR test transmission and the subsequent detection of a
       -- collision or deassertion of carrier.  On successful completion
       -- of a TDR test, the appropriate instance of ifExtnsTestResult
       -- contains the OBJECT IDENTIFIER of the MIB object which
       -- contains the value of this time interval.



Kastenholz                                                     [Page 13]


RFC 1398                   Ethernet-Like MIB                January 1993


4.4.  802.3 Hardware Chipsets


       --  802.3 Hardware Chipsets

       -- The object ifExtnsChipSet is provided in RFC 1229 to identify
       -- the MAC hardware used to communcate on an interface.  The
       -- following hardware chipsets are provided for 802.3:

  dot3ChipSets          OBJECT IDENTIFIER ::= { dot3 8 }
  dot3ChipSetAMD        OBJECT IDENTIFIER ::= { dot3ChipSets 1 }
  dot3ChipSetAMD7990    OBJECT IDENTIFIER ::= { dot3ChipSetAMD 1 }
  dot3ChipSetAMD79900   OBJECT IDENTIFIER ::= { dot3ChipSetAMD 2 }

  dot3ChipSetIntel      OBJECT IDENTIFIER ::= { dot3ChipSets 2 }
  dot3ChipSetIntel82586 OBJECT IDENTIFIER ::= { dot3ChipSetIntel 1 }
  dot3ChipSetIntel82596 OBJECT IDENTIFIER ::= { dot3ChipSetIntel 2 }
  dot3ChipSetSeeq       OBJECT IDENTIFIER ::= { dot3ChipSets 3 }
  dot3ChipSetSeeq8003   OBJECT IDENTIFIER ::= { dot3ChipSetSeeq 1 }

  dot3ChipSetNational      OBJECT IDENTIFIER ::= { dot3ChipSets 4 }
  dot3ChipSetNational8390  OBJECT IDENTIFIER ::=
                                           { dot3ChipSetNational 1 }
  dot3ChipSetNationalSonic OBJECT IDENTIFIER ::=
                                           { dot3ChipSetNational 2 }

  dot3ChipSetFujitsu       OBJECT IDENTIFIER ::= { dot3ChipSets 5 }
  dot3ChipSetFujitsu86950  OBJECT IDENTIFIER ::=
                                           { dot3ChipSetFujitsu 1 }
  dot3ChipSetFujitsu86960  OBJECT IDENTIFIER ::=
                                           { dot3ChipSetFujitsu 2 }

       -- For those chipsets not represented above, OBJECT IDENTIFIER
       -- assignment is required in other documentation, e.g., assignment
       -- within that part of the registration tree delegated to
       -- individual enterprises (see RFC 1155).

          END

5.  Change Log

  (1)  Replace old "Historical Perspective" boilerplate with the
       new "The Network Management Framework" boilerplate.

  (2)  Remove the "slime text".

  (3)  Updated the reference to the Interface Extensions mib to
       reflect its new RFC status.



Kastenholz                                                     [Page 14]


RFC 1398                   Ethernet-Like MIB                January 1993


  (4)  Change the status of the memo section to hold the new
       suggested text.

  (5)  References in ASN.1 comments were changed from the [#]
       form to name the actual document being referred to. These
       references are now meaningful when the ASN.1 is read
       outside of the RFC.

  (6)  The IMPORTS section of the ASN.1 has been updated to
       reflect that the OBJECT-TYPE macro is imported from RFC-
       1212.

  (7)  The the Generic Ethernet-like group, containing
       dot3Index, dot3InitializeMac, dot3MacSubLayerStatus,
       dot3MulticastReceiveStatus, dot3TxEnabled, and
       dot3TestTdrValue has been deprecated as a result of the
       implementation experience presented at the San Diego IETF
       meeting.

  (8)  dot3StatsInRangeLengthErrors and
       dot3StatsOutOfRangeLengthFields have been deprecated as a
       result of the implementation experience presented at the
       San Diego IETF meeting.

  (9)  Update the acknowledgements section to reflect this
       document's history, etc.

  (10) REFERENCE clauses have been added to all of the MIB
       objects which are being retained.

  12 August 1992

  (1)  Removed all deprecated objects.

  (2)  Rephrased the description of the TDR test OID to reflect
       the fact that dot3TestTdrValue is no more.
       ifExtnsTestResult still points to the object containing
       the result, the text simply does not refer to
       dot3TestTdrValue. I could have deleted the Test, but the
       OID should then remain reserved. I figured that it would
       be just as easy to rephrase the definition of the test.

  13 august 1992

  (1)  Add fuji. 86960






Kastenholz                                                     [Page 15]


RFC 1398                   Ethernet-Like MIB                January 1993


6.  Acknowledgements

   This document was produced by the Ethernet MIB Working Group.

   This document is based on the Proposed Standard Ethernet MIB, RFC
   1284 [14], of which John Cook of Chipcom was the editor.  The
   Ethernet MIB Working Group gathered implementation experience of the
   variables specified in RFC 1284 and used that information to develop
   this revised MIB.

   RFC 1284, in turn, is based on a document written by Frank Kastenholz
   of Interlan entitled IEEE 802.3 Layer Management Draft M compatible
   MIB for TCP/IP Networks [10].  This document has been modestly
   reworked, initially by the SNMP Working Group, and then by the
   Transmission Working Group, to reflect the current conventions for
   defining objects for MIB interfaces.  James Davin, of the MIT
   Laboratory for Computer Science, and Keith McCloghrie of Hughes LAN
   Systems, contributed to later drafts of this memo. Marshall Rose of
   Performance Systems International, Inc. converted the document into
   its current concise format. Anil Rijsinghani of DEC contributed text
   that more adequately describes the TDR test.  Thanks to Frank
   Kastenholz of Interlan and Louis Steinberg of IBM for their
   experimentation.

7.  References

   [1] Cerf, V., "IAB Recommendations for the Development of Internet
       Network Management Standards", RFC 1052, NRI, April 1988.

   [2] Cerf, V., "Report of the Second Ad Hoc Network Management Review
       Group", RFC 1109, NRI, August 1989.

   [3] Rose M., and K. McCloghrie, "Structure and Identification of
       Management Information for TCP/IP-based internets", STD 16, RFC
       1155, Performance Systems International, Hughes LAN Systems, May
       1990.

   [4] McCloghrie K., and M. Rose, "Management Information Base for
       Network Management of TCP/IP-based internets", RFC 1156, Hughes
       LAN Systems, Performance Systems International, May 1990.

   [5] Case, J., Fedor, M., Schoffstall, M., and J. Davin, "Simple
       Network Management Protocol", STD 15, RFC 1157, SNMP Research,
       Performance Systems International, Performance Systems
       International, MIT Laboratory for Computer Science, May 1990.

   [6] Rose M., Editor, "Management Information Base for Network
       Management of TCP/IP-based internets: MIB-II", STD 17, RFC 1213,



Kastenholz                                                     [Page 16]


RFC 1398                   Ethernet-Like MIB                January 1993


       Performance Systems International, March 1991.

   [7] Information processing systems - Open Systems Interconnection -
       Specification of Abstract Syntax Notation One (ASN.1),
       International Organization for Standardization, International
       Standard 8824, December 1987.

   [8] Information processing systems - Open Systems Interconnection -
       Specification of Basic Encoding Rules for Abstract Notation One
       (ASN.1), International Organization for Standardization,
       International Standard 8825, December 1987.

   [9] IEEE, "IEEE 802.3 Layer Management", November 1988.

  [10] Kastenholz, F., "IEEE 802.3 Layer Management Draft compatible MIB
       for TCP/IP Networks", electronic mail message to mib-
       wg@nnsc.nsf.net, 9 June 1989.

  [11] McCloghrie, K., Editor, Extensions to the Generic-Interface MIB,
       RFC 1229, Hughes LAN Systems, Inc., May 1991.

  [12] IEEE, "Carrier Sense Multiple Access with Collision Detection
       (CSMA/CD) Access Method and Physical Layer Specifications",
       ANSI/IEEE Std 802.3-1985.

  [13] Rose, M., and K. McCloghrie, Editors, "Concise MIB Definitions",
       STD 16, RFC 1212, Performance Systems International, Hughes LAN
       Systems, March 1991.

  [14] Cook, J., Editor, "Definitions of Managed Objects for Ethernet-
       Like Interface Types", RFC 1284, Chipcom Corporation, December
       1991.

8.  Security Considerations

   Security issues are not discussed in this memo.

9.  Author's Address

   Frank Kastenholz
   2 High Street
   North Andover, MA 01845-2620

   Phone: (508) 685-4000
   EMail: kasten@ftp.com






Kastenholz                                                     [Page 17]

mirror server hosted at Truenetwork, Russian Federation.