Network Working Group C. Brown
Request for Comments: 2115 Cadia Networks, Inc.
Obsoletes: 1315 F. Baker
Category: Standards Track Cisco Systems
September 1997
Management Information Base for Frame Relay DTEs
Using SMIv2
1. Status of this Memo
This document specifies an Internet standards track protocol for the
Internet community, and requests discussion and suggestions for
improvements. Please refer to the current edition of the "Internet
Official Protocol Standards" (STD 1) for the standardization state
and status of this protocol. Distribution of this memo is unlimited.
2. Abstract
This memo defines a portion of the Management Information Base (MIB)
for use with network management protocols in TCP/IP- based internets.
In particular, it defines objects for managing Frame Relay interfaces
on DTEs.
Table of Contents
1 Status of this Memo ................................... 1
2 Abstract .............................................. 1
3 The SNMPv2 Network Management Framework ............... 2
4 Overview .............................................. 2
4.1 Frame Relay Operational Model ....................... 2
4.2 Textual Conventions ................................. 6
4.3 Structure of MIB .................................... 6
5 Changes from RFC 1315 ................................. 6
6 Definitions ........................................... 8
6.1 Data Link Connection Management Interface ........... 9
6.2 Circuit Table ....................................... 14
6.3 Error Table ......................................... 22
6.4 Trap Management ..................................... 25
7 Security Issues ....................................... 30
8 Acknowledgments ....................................... 30
9 Authors' Addresses .................................... 31
10 References ........................................... 31
Brown & Baker Standards Track [Page 1]
RFC 2115 Frame Relay DTE MIB September 1997 3. The SNMPv2 Network Management Framework The major components of the SNMPv2 Network Management framework are described in the documents listed below. o RFC 1902 [1] defines the Structure of Management Information (SMI), the mechanisms used for describing and naming objects for the purpose of management. o STD 17, RFC 1213 [2] defines MIB-II, the core set of managed objects (MO) for the Internet suite of protocols. o RFC 1905 [3] defines the protocol used for network access to managed objects. The framework is adaptable/extensible by defining new MIBs to suit the requirements of specific applications/protocols/situations. Managed objects are accessed via a virtual information store, the MIB. Objects in the MIB are defined using the subset of Abstract Syntax Notation One (ASN.1) defined in the SMI. In particular, each object type is named by an OBJECT IDENTIFIER, which is an administratively assigned name. The object type together with an object instance serves to uniquely identify a specific instantiation of the object. For human convenience, often a textual string, termed the descriptor, is used to refer to the object type. 4. Overview 4.1. Frame Relay Operational Model For the purposes of understanding this document, Frame Relay is viewed as a multi-access media, not as a group of point- to-point connections. This model proposes that Frame Relay is a single interface to the network (physical connection) with many destinations or neighbors (virtual connections). This view enables a network manager the ability to group all virtual connections with their corresponding physical connection thereby allowing simpler diagnostics and trouble shooting. With the extension of the interfaces MIB, it is possible to configure frame relay DLCs as individual interfaces and create ifTable entries for each. This is not recommended and is not directly supported by this MIB. Additionally, in the presence of demand circuits creation of individual ifEntries for each is not possible. Brown & Baker Standards Track [Page 2]
RFC 2115 Frame Relay DTE MIB September 1997 Should the user wish to group DLCs together to associate them with a higher layer, or to associate a DLC with an unnumbered point-to-point service, the frame relay DTE MIB provides an entry in the frCircuitEntry record. For example, suppose one were to configure a company proprietary protocol to run above several of the frame relay VCs. The basic layering would look something like the following: IP (ipaddrEntry 1 ) IP (ipaddrEntry 2) IP (ipaddrEntry 3) | | | | | | | | proprietary protocol | | layer (ifIndex 3) | | | | | | DLCI 20 DLCI 30 DLCI 40/41/42 (ifIndex 2) (ifIndex 2) (ifIndex 2, logical ifIndex 3) | | | | | | |____________________|_____________________| | | FR DLMCI (ifIndex.2) | | Physical Interface (ifIndex.1) A configuration which specified that DLCI 40, 41,and 42 were associated with a proprietary protocol layer, while DLCI 20 and 30 were to run IP directly can now be expressed using a combination of frCircuitIfIndex and frCircuitLogicalIfIndex. In this particular case DLCIs 40, 41 and 42 would use frCircuitIfIndex equal to the frame relay interface level (2) while their frCircuitLogicalIfIndex would indicate the proprietary protocol (3). DLCIs 20 and 30 would have both instances set to the frame relay interface (2). Object Meaning for Frame Relay Interface ______ _____________________________________ ifDescr As per DESCRIPTION in RFC 1573. ifType The value allocated for Frame Relay Interfaces - frameRelay (32). ifMtu Set to maximum frame size in octets for this frame relay interface. Brown & Baker Standards Track [Page 3]
RFC 2115 Frame Relay DTE MIB September 1997 ifSpeed The access rate for the frame relay interface. This could be different from the speed of the underlying physical interface, e.g. in a fractional T1 case the access rate could be 384 kbits/s (the value reported in this object) whereas the speed of the underlying interface would be 1.544 Mbits/s (the value reported in the instance of ifSpeed for the ifEntry with type ds1). ifPhysAddress The primary address for this interface assigned by the Frame Relay interface provider. An octet string of zero length if no address is used for this interface. ifAdminStatus As per DESCRIPTION in RFC 1573. ifOperStatus As per DESCRIPTION in RFC 1573. ifLastChange As per DESCRIPTION in RFC 1573. ifInOctets The number of received octets. This includes not only the information field (user data) but also the frame relay header and CRC. ifInUcastPkts The number of frames received on non- multicast DLCIs ifInDiscards The number of frames that were successfully received but were discarded because of format errors or because the VC was not known. Format errors, in this case, are any errors which would prevent the system from recognizing the DLCI and placing the error in the frCircuitDiscard category. ifInErrors The number of received frames that are discarded, because of an error. Possible errors can be the following: the frame relay frames were too long or were too short, the frames had an invalid or unrecognized DLCI values, or incorrect header values. Brown & Baker Standards Track [Page 4]
RFC 2115 Frame Relay DTE MIB September 1997 ifInUnknownProtos Number of unknown or unsupported upper layer protocol frames received and discarded. ifOutOctets The number of received octets. This includes not only the information field (user data) but also the frame relay header and CRC. ifOutUcastpkts The number of frames sent. ifOutDiscards The number of frames discarded in the transmit direction. ifOutErrors The number of frames discarded in the egress direction, because of errors. ifName As per DESCRIPTION in RFC 1573. ifInMulticastPkts The number of unerrored frames received on a multicast DLCI. ifInBroadcastPkts Always zero (0) as there are no broadcast frames. ifOutMulticastPkts The number of frames transmitted over a multicast DLCI. ifOutBroadcastPkts Always zero (0) as there are no broadcast frames. ifHCInOctets Only required when ifSpeed >= 155 Mbits/s. See details for ifInOctets. ifHCOutOctets Only required when ifSpeed >= 155 Mbits/s. See details for ifInOctets. ifLinkUpDownTrapEnble As per DESCRIPTION in RFC 1573. ifHighSpeed The access rate of the frame relay interface measured in Mbits/s. If the access rate is less than 1 Mbits/s, this object returns 0. ifPromiscuousMode Set to false(2). ifConnectorPresent Set to false(2). Brown & Baker Standards Track [Page 5]
RFC 2115 Frame Relay DTE MIB September 1997 4.2. Textual Conventions One new data type is introduced as a textual convention in this MIB document. This textual convention enhances the readability of the specification and can ease comparison with other specifications if appropriate. It should be noted that the introduction of this textual conventions has no effect on either the syntax nor the semantics of any managed objects. The use of this is merely an artifact of the explanatory method used. Objects defined in terms of one of these methods are always encoded by means of the rules that define the primitive type. Hence, no changes to the SMI or the SNMP are necessary to accommodate this textual conventions which is adopted merely for the convenience of readers and writers in pursuit of the elusive goal of clear, concise, and unambiguous MIB documents. The new data type is DLCI. DLCI refers to the range 0..DLCINumber, and is used to refer to the valid Data Link Connection Indices. DLCINumber is, by definition, the largest possible DLCI value possible under the configured Q.922 Address Format. 4.3. Structure of MIB The MIB is composed of three groups, one defining the Data Link Connection Management Interface (DLCMI), one describing the Circuits, and a third describing errors. During normal operation, Frame Relay virtual circuits will be added, deleted and change availability. The occurrence of such changes is of interest to the network manager and therefore, one trap is defined, intended to be corollary to the SNMP "Link Up" and "Link Down" traps. 5. Changes from RFC 1315 Below are listed the changes from the previously published version this document, which was RFC 1315: o The MIB module was converted from SMIv1 to SMIv2 format. Note: due to this, the table indices have access of "read-only" instead of "not-accessible", which is the typical value for index objects in SMIv2. o The module name was changed from RFC1315-MIB to FRAME- RELAY-DTE-MIB. o The textual convention "Index" was dropped from the MIB module and "InterfaceIndex" from the interfaces MIB module, IF-MIB, was used in its place. Brown & Baker Standards Track [Page 6]
RFC 2115 Frame Relay DTE MIB September 1997 o Objects frDlcmiStatus and frDlcmiRowStatus were added to table frDlcmiTable. o Added values "itut933A(5)" (from CCITT Q933 Annex A) and "ansiT1617D1994(6)" (from ANSI T1.617a-1994 Annex D) to the enumerations for object frDlcmiState. o The labels for the enumerated values for object frDlcmiAddressLen were renamed to remove their hyphens as required by SMIv2. o Added clarification that the "management virtual circuit" (i.e. DLCI 0) is a member of the circuit table. o Added the following objects to table frCircuitTable: frCircuitMulticast, frCircuitType, frCircuitDiscards, frCircuitReceivedDEs, frCircuitSentDEs, frCircuitLogicalIfIndex, and frCircuitRowStatus. o The definition of object frCircuitReceivedOctets was clarified as to which octets were counted. o Added the objects frErrFaults and frErrFaultTime to table frErrTable. o Added clarification to the values of object frErrType. o Added size on definition of object frErrData and clarified what data to capture. o Changed identififier for OID value { frameDelayDTE 4 } from frame-relay-globals to frameRelayTrapControl. o Added object frTrapMaxRate. o Created object groups frPortGroup, frCircuitGroup, frTrapGroup, frErrGroup, frPortGroup0, frCircuitGroup0, frTrapGroup0, and frErrGroup0. o Created notification group frNotificationGroup. o Created module compliances frCompliance and frCompliance0. o Added ranges to objects frCircuitCommittedBurst, frCircuitExcessBurst, and frCircuitThroughput. Brown & Baker Standards Track [Page 7]
RFC 2115 Frame Relay DTE MIB September 1997 6. Definitions FRAME-RELAY-DTE-MIB DEFINITIONS ::= BEGIN IMPORTS MODULE-IDENTITY, OBJECT-TYPE, Counter32, Integer32, NOTIFICATION-TYPE FROM SNMPv2-SMI TEXTUAL-CONVENTION, RowStatus, TimeStamp FROM SNMPv2-TC MODULE-COMPLIANCE, OBJECT-GROUP, NOTIFICATION-GROUP FROM SNMPv2-CONF transmission FROM RFC1213-MIB InterfaceIndex FROM IF-MIB; -- Frame Relay DTE MIB frameRelayDTE MODULE-IDENTITY LAST-UPDATED "9705010229Z" -- Thu May 1 02:29:46 PDT 1997 ORGANIZATION "IETF IPLPDN Working Group" CONTACT-INFO " Caralyn Brown Postal: Cadia Networks, Inc. 1 Corporate Drive Andover, Massachusetts 01810 Tel: +1 508 689 2400 x133 E-Mail: cbrown@cadia.com Fred Baker Postal: Cisco Systems 519 Lado Drive Santa Barbara, California 93111 Tel: +1 408 526 425 E-Mail: fred@cisco.com" DESCRIPTION "The MIB module to describe the use of a Frame Relay interface by a DTE." REVISION "9705010229Z" -- Thu May 1 02:29:46 PDT 1997 DESCRIPTION "Converted from SMIv1 to SMIv2. (Thus, indices are read-only rather than being not-accessible.) Added objects and made clarifications based on implementation experience." REVISION "9204010000Z" DESCRIPTION "Published as RFC 1315, the initial version of this MIB module." ::= { transmission 32 } Brown & Baker Standards Track [Page 8]
RFC 2115 Frame Relay DTE MIB September 1997 -- -- the range of a Data Link Connection Identifier -- DLCI ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "The range of DLCI values. Note that this varies by interface configuration; normally, interfaces may use 0..1023, but may be configured to use ranges as large as 0..2^23." SYNTAX Integer32(0..8388607) -- -- Data Link Connection Management Interface -- The variables that configure the DLC Management Interface. frDlcmiTable OBJECT-TYPE SYNTAX SEQUENCE OF FrDlcmiEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The Parameters for the Data Link Connection Management Interface for the frame relay service on this interface." REFERENCE "American National Standard T1.617-1991, Annex D" ::= { frameRelayDTE 1 } frDlcmiEntry OBJECT-TYPE SYNTAX FrDlcmiEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The Parameters for a particular Data Link Connection Management Interface." INDEX { frDlcmiIfIndex } ::= { frDlcmiTable 1 } Brown & Baker Standards Track [Page 9]
RFC 2115 Frame Relay DTE MIB September 1997 FrDlcmiEntry ::= SEQUENCE { frDlcmiIfIndex InterfaceIndex, frDlcmiState INTEGER, frDlcmiAddress INTEGER, frDlcmiAddressLen INTEGER, frDlcmiPollingInterval Integer32, frDlcmiFullEnquiryInterval Integer32, frDlcmiErrorThreshold Integer32, frDlcmiMonitoredEvents Integer32, frDlcmiMaxSupportedVCs DLCI, frDlcmiMulticast INTEGER, frDlcmiStatus INTEGER, frDlcmiRowStatus RowStatus } frDlcmiIfIndex OBJECT-TYPE SYNTAX InterfaceIndex MAX-ACCESS read-only STATUS current DESCRIPTION "The ifIndex value of the corresponding ifEntry." ::= { frDlcmiEntry 1 } frDlcmiState OBJECT-TYPE SYNTAX INTEGER { noLmiConfigured (1), lmiRev1 (2), ansiT1617D (3), -- ANSI T1.617 Annex D ansiT1617B (4), -- ANSI T1.617 Annex B itut933A (5), -- CCITT Q933 Annex A ansiT1617D1994 (6) -- ANSI T1.617a-1994 Annex D } MAX-ACCESS read-create STATUS current DESCRIPTION "This variable states which Data Link Connection Management scheme is active (and by implication, what DLCI it uses) on the Frame Relay interface." REFERENCE "American National Standard T1.617-1991, American National Standard T1.617a-1994, ITU-T Recommendation Q.933 (03/93)." ::= { frDlcmiEntry 2 } Brown & Baker Standards Track [Page 10]
RFC 2115 Frame Relay DTE MIB September 1997 frDlcmiAddress OBJECT-TYPE SYNTAX INTEGER { q921 (1), -- 13 bit DLCI q922March90 (2), -- 11 bit DLCI q922November90 (3), -- 10 bit DLCI q922 (4) -- Final Standard } MAX-ACCESS read-create STATUS current DESCRIPTION "This variable states which address format is in use on the Frame Relay interface." ::= { frDlcmiEntry 3 } frDlcmiAddressLen OBJECT-TYPE SYNTAX INTEGER { twoOctets (2), threeOctets (3), fourOctets (4) } MAX-ACCESS read-create STATUS current DESCRIPTION "This variable states the address length in octets. In the case of Q922 format, the length indicates the entire length of the address including the control portion." ::= { frDlcmiEntry 4 } frDlcmiPollingInterval OBJECT-TYPE SYNTAX Integer32 (5..30) UNITS "seconds" MAX-ACCESS read-create STATUS current DESCRIPTION "This is the number of seconds between successive status enquiry messages." REFERENCE "American National Standard T1.617-1991, Section D.7 Timer T391." DEFVAL { 10 } ::= { frDlcmiEntry 5 } Brown & Baker Standards Track [Page 11]
RFC 2115 Frame Relay DTE MIB September 1997 frDlcmiFullEnquiryInterval OBJECT-TYPE SYNTAX Integer32 (1..255) MAX-ACCESS read-create STATUS current DESCRIPTION "Number of status enquiry intervals that pass before issuance of a full status enquiry message." REFERENCE "American National Standard T1.617-1991, Section D.7 Counter N391." DEFVAL { 6 } ::= { frDlcmiEntry 6 } frDlcmiErrorThreshold OBJECT-TYPE SYNTAX Integer32 (1..10) MAX-ACCESS read-create STATUS current DESCRIPTION "This is the maximum number of unanswered Status Enquiries the equipment shall accept before declaring the interface down." REFERENCE "American National Standard T1.617-1991, Section D.5.1 Counter N392." DEFVAL { 3 } ::= { frDlcmiEntry 7 } frDlcmiMonitoredEvents OBJECT-TYPE SYNTAX Integer32 (1..10) MAX-ACCESS read-create STATUS current DESCRIPTION "This is the number of status polling intervals over which the error threshold is counted. For example, if within 'MonitoredEvents' number of events the station receives 'ErrorThreshold' number of errors, the interface is marked as down." REFERENCE "American National Standard T1.617-1991, Section D.5.2 Counter N393." DEFVAL { 4 } ::= { frDlcmiEntry 8 } Brown & Baker Standards Track [Page 12]
RFC 2115 Frame Relay DTE MIB September 1997 frDlcmiMaxSupportedVCs OBJECT-TYPE SYNTAX DLCI MAX-ACCESS read-create STATUS current DESCRIPTION "The maximum number of Virtual Circuits allowed for this interface. Usually dictated by the Frame Relay network. In response to a SET, if a value less than zero or higher than the agent's maximal capability is configured, the agent should respond badValue" ::= { frDlcmiEntry 9 } frDlcmiMulticast OBJECT-TYPE SYNTAX INTEGER { nonBroadcast (1), broadcast (2) } MAX-ACCESS read-create STATUS current DESCRIPTION "This indicates whether the Frame Relay interface is using a multicast service." ::= { frDlcmiEntry 10 } frDlcmiStatus OBJECT-TYPE SYNTAX INTEGER { running (1), -- init complete, system running fault (2), -- error threshold exceeded initializing (3) -- system start up } MAX-ACCESS read-only STATUS current DESCRIPTION "This indicates the status of the Frame Relay interface as determined by the performance of the dlcmi. If no dlcmi is running, the Frame Relay interface will stay in the running state indefinitely." ::= { frDlcmiEntry 11 } Brown & Baker Standards Track [Page 13]
RFC 2115 Frame Relay DTE MIB September 1997 frDlcmiRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "SNMP Version 2 Row Status Variable. Writable objects in the table may be written in any RowStatus state." ::= { frDlcmiEntry 12 } -- -- A Frame Relay service is a multiplexing service. Data -- Link Connection Identifiers enumerate virtual circuits -- (permanent or dynamic) which are layered onto the underlying -- circuit, represented by ifEntry. Therefore, each of the entries -- in the Standard MIB's Interface Table with an IfType of -- Frame Relay represents a Q.922 interface. Zero or more -- virtual circuits are layered onto this interface and provide -- interconnection with various remote destinations. -- Each such virtual circuit is represented by an entry in the -- circuit table. The management virtual circuit (i.e. DLCI 0) -- is a virtual circuit by this definition and will be represented -- with an entry in the circuit table. -- Circuit Table -- The table describing the use of the DLCIs attached to -- each Frame Relay Interface. frCircuitTable OBJECT-TYPE SYNTAX SEQUENCE OF FrCircuitEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table containing information about specific Data Link Connections (DLC) or virtual circuits." ::= { frameRelayDTE 2 } Brown & Baker Standards Track [Page 14]
RFC 2115 Frame Relay DTE MIB September 1997 frCircuitEntry OBJECT-TYPE SYNTAX FrCircuitEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The information regarding a single Data Link Connection. Discontinuities in the counters contained in this table are indicated by the value in frCircuitCreationTime." INDEX { frCircuitIfIndex, frCircuitDlci } ::= { frCircuitTable 1 } FrCircuitEntry ::= SEQUENCE { frCircuitIfIndex InterfaceIndex, frCircuitDlci DLCI, frCircuitState INTEGER, frCircuitReceivedFECNs Counter32, frCircuitReceivedBECNs Counter32, frCircuitSentFrames Counter32, frCircuitSentOctets Counter32, frCircuitReceivedFrames Counter32, frCircuitReceivedOctets Counter32, frCircuitCreationTime TimeStamp, frCircuitLastTimeChange TimeStamp, frCircuitCommittedBurst Integer32, frCircuitExcessBurst Integer32, frCircuitThroughput Integer32, frCircuitMulticast INTEGER, frCircuitType INTEGER, frCircuitDiscards Counter32, frCircuitReceivedDEs Counter32, frCircuitSentDEs Counter32, frCircuitLogicalIfIndex InterfaceIndex, frCircuitRowStatus RowStatus } frCircuitIfIndex OBJECT-TYPE SYNTAX InterfaceIndex MAX-ACCESS read-only STATUS current DESCRIPTION "The ifIndex Value of the ifEntry this virtual circuit is layered onto." ::= { frCircuitEntry 1 } Brown & Baker Standards Track [Page 15]
RFC 2115 Frame Relay DTE MIB September 1997 frCircuitDlci OBJECT-TYPE SYNTAX DLCI MAX-ACCESS read-only STATUS current DESCRIPTION "The Data Link Connection Identifier for this virtual circuit." REFERENCE "American National Standard T1.618-1991, Section 3.3.6" ::= { frCircuitEntry 2 } frCircuitState OBJECT-TYPE SYNTAX INTEGER { invalid (1), active (2), inactive (3) } MAX-ACCESS read-create STATUS current DESCRIPTION "Indicates whether the particular virtual circuit is operational. In the absence of a Data Link Connection Management Interface, virtual circuit entries (rows) may be created by setting virtual circuit state to 'active', or deleted by changing Circuit state to 'invalid'. Whether or not the row actually disappears is left to the implementation, so this object may actually read as 'invalid' for some arbitrary length of time. It is also legal to set the state of a virtual circuit to 'inactive' to temporarily disable a given circuit. The use of 'invalid' is deprecated in this SNMP Version 2 MIB, in favor of frCircuitRowStatus." DEFVAL { active } ::= { frCircuitEntry 3 } Brown & Baker Standards Track [Page 16]
RFC 2115 Frame Relay DTE MIB September 1997 frCircuitReceivedFECNs OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of frames received from the network indicating forward congestion since the virtual circuit was created. This occurs when the remote DTE sets the FECN flag, or when a switch in the network enqueues the frame to a trunk whose transmission queue is congested." REFERENCE "American National Standard T1.618-1991, Section 3.3.3" ::= { frCircuitEntry 4 } frCircuitReceivedBECNs OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of frames received from the network indicating backward congestion since the virtual circuit was created. This occurs when the remote DTE sets the BECN flag, or when a switch in the network receives the frame from a trunk whose transmission queue is congested." REFERENCE "American National Standard T1.618-1991, Section 3.3.4" ::= { frCircuitEntry 5 } frCircuitSentFrames OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of frames sent from this virtual circuit since it was created." ::= { frCircuitEntry 6 } frCircuitSentOctets OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current Brown & Baker Standards Track [Page 17]
RFC 2115 Frame Relay DTE MIB September 1997 DESCRIPTION "The number of octets sent from this virtual circuit since it was created. Octets counted are the full frame relay header and the payload, but do not include the flag characters or CRC." ::= { frCircuitEntry 7 } frCircuitReceivedFrames OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of frames received over this virtual circuit since it was created." ::= { frCircuitEntry 8 } frCircuitReceivedOctets OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of octets received over this virtual circuit since it was created. Octets counted include the full frame relay header, but do not include the flag characters or the CRC." ::= { frCircuitEntry 9 } frCircuitCreationTime OBJECT-TYPE SYNTAX TimeStamp MAX-ACCESS read-only STATUS current DESCRIPTION "The value of sysUpTime when the virtual circuit was created, whether by the Data Link Connection Management Interface or by a SetRequest." ::= { frCircuitEntry 10 } Brown & Baker Standards Track [Page 18]
RFC 2115 Frame Relay DTE MIB September 1997 frCircuitLastTimeChange OBJECT-TYPE SYNTAX TimeStamp MAX-ACCESS read-only STATUS current DESCRIPTION "The value of sysUpTime when last there was a change in the virtual circuit state" ::= { frCircuitEntry 11 } frCircuitCommittedBurst OBJECT-TYPE SYNTAX Integer32(0..2147483647) MAX-ACCESS read-create STATUS current DESCRIPTION "This variable indicates the maximum amount of data, in bits, that the network agrees to transfer under normal conditions, during the measurement interval." REFERENCE "American National Standard T1.617-1991, Section 6.5.19" DEFVAL { 0 } -- the default indicates no commitment ::= { frCircuitEntry 12 } frCircuitExcessBurst OBJECT-TYPE SYNTAX Integer32(0..2147483647) MAX-ACCESS read-create STATUS current DESCRIPTION "This variable indicates the maximum amount of uncommitted data bits that the network will attempt to deliver over the measurement interval. By default, if not configured when creating the entry, the Excess Information Burst Size is set to the value of ifSpeed." REFERENCE "American National Standard T1.617-1991, Section 6.5.19" ::= { frCircuitEntry 13 } frCircuitThroughput OBJECT-TYPE SYNTAX Integer32(0..2147483647) MAX-ACCESS read-create STATUS current DESCRIPTION Brown & Baker Standards Track [Page 19]
RFC 2115 Frame Relay DTE MIB September 1997 "Throughput is the average number of 'Frame Relay Information Field' bits transferred per second across a user network interface in one direction, measured over the measurement interval. If the configured committed burst rate and throughput are both non-zero, the measurement interval, T, is T=frCircuitCommittedBurst/frCircuitThroughput. If the configured committed burst rate and throughput are both zero, the measurement interval, T, is T=frCircuitExcessBurst/ifSpeed." REFERENCE "American National Standard T1.617-1991, Section 6.5.19" DEFVAL {0} -- the default value of Throughput is -- "no commitment". ::= { frCircuitEntry 14 } frCircuitMulticast OBJECT-TYPE SYNTAX INTEGER { unicast (1), oneWay (2), twoWay (3), nWay (4) } MAX-ACCESS read-create STATUS current DESCRIPTION "This indicates whether this VC is used as a unicast VC (i.e. not multicast) or the type of multicast service subscribed to" REFERENCE "Frame Relay PVC Multicast Service and Protocol Description Implementation: FRF.7 Frame Relay Forum Technical Committe October 21, 1994" DEFVAL {unicast} -- the default value of frCircuitMulticast is -- "unicast" (not a multicast VC). ::= { frCircuitEntry 15 } frCircuitType OBJECT-TYPE SYNTAX INTEGER { static (1), dynamic (2) } Brown & Baker Standards Track [Page 20]
RFC 2115 Frame Relay DTE MIB September 1997 MAX-ACCESS read-only STATUS current DESCRIPTION "Indication of whether the VC was manually created (static), or dynamically created (dynamic) via the data link control management interface." ::= { frCircuitEntry 16 } frCircuitDiscards OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of inbound frames dropped because of format errors, or because the VC is inactive." ::= { frCircuitEntry 17 } frCircuitReceivedDEs OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of frames received from the network indicating that they were eligible for discard since the virtual circuit was created. This occurs when the remote DTE sets the DE flag, or when in remote DTE's switch detects that the frame was received as Excess Burst data." REFERENCE "American National Standard T1.618-1991, Section 3.3.4" ::= { frCircuitEntry 18 } frCircuitSentDEs OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of frames sent to the network indicating that they were eligible for discard since the virtual circuit was created. This occurs when the local DTE sets the DE flag, indicating that during Network congestion situations those frames should be discarded in preference of other frames sent without the DE bit set." REFERENCE Brown & Baker Standards Track [Page 21]
RFC 2115 Frame Relay DTE MIB September 1997 "American National Standard T1.618-1991, Section 3.3.4" ::= { frCircuitEntry 19 } frCircuitLogicalIfIndex OBJECT-TYPE SYNTAX InterfaceIndex MAX-ACCESS read-create STATUS current DESCRIPTION "Normally the same value as frDlcmiIfIndex, but different when an implementation associates a virtual ifEntry with a DLC or set of DLCs in order to associate higher layer objects such as the ipAddrEntry with a subset of the virtual circuits on a Frame Relay interface. The type of such ifEntries is defined by the higher layer object; for example, if PPP/Frame Relay is implemented, the ifType of this ifEntry would be PPP. If it is not so defined, as would be the case with an ipAddrEntry, it should be of type Other." ::= { frCircuitEntry 20 } frCircuitRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "This object is used to create a new row or modify or destroy an existing row in the manner described in the definition of the RowStatus textual convention. Writable objects in the table may be written in any RowStatus state." ::= { frCircuitEntry 21 } -- -- Error Table -- The table describing errors encountered on each Frame -- Relay Interface. frErrTable OBJECT-TYPE SYNTAX SEQUENCE OF FrErrEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table containing information about Errors on the Frame Relay interface. Discontinuities in the counters contained in this table are the same as apply to the Brown & Baker Standards Track [Page 22]
RFC 2115 Frame Relay DTE MIB September 1997 ifEntry associated with the Interface." ::= { frameRelayDTE 3 } frErrEntry OBJECT-TYPE SYNTAX FrErrEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The error information for a single frame relay interface." INDEX { frErrIfIndex } ::= { frErrTable 1 } FrErrEntry ::= SEQUENCE { frErrIfIndex InterfaceIndex, frErrType INTEGER, frErrData OCTET STRING, frErrTime TimeStamp, frErrFaults Counter32, frErrFaultTime TimeStamp } frErrIfIndex OBJECT-TYPE SYNTAX InterfaceIndex MAX-ACCESS read-only STATUS current DESCRIPTION "The ifIndex Value of the corresponding ifEntry." ::= { frErrEntry 1 } frErrType OBJECT-TYPE SYNTAX INTEGER { unknownError(1), receiveShort(2), receiveLong(3), illegalAddress(4), unknownAddress(5), dlcmiProtoErr(6), dlcmiUnknownIE(7), dlcmiSequenceErr(8), dlcmiUnknownRpt(9), noErrorSinceReset(10) } Brown & Baker Standards Track [Page 23]
RFC 2115 Frame Relay DTE MIB September 1997 MAX-ACCESS read-only STATUS current DESCRIPTION "The type of error that was last seen on this interface: receiveShort: frame was not long enough to allow demultiplexing - the address field was incomplete, or for virtual circuits using Multiprotocol over Frame Relay, the protocol identifier was missing or incomplete. receiveLong: frame exceeded maximum length configured for this interface. illegalAddress: address field did not match configured format. unknownAddress: frame received on a virtual circuit which was not active or administratively disabled. dlcmiProtoErr: unspecified error occurred when attempting to interpret link maintenance frame. dlcmiUnknownIE: link maintenance frame contained an Information Element type which is not valid for the configured link maintenance protocol. dlcmiSequenceErr: link maintenance frame contained a sequence number other than the expected value. dlcmiUnknownRpt: link maintenance frame contained a Report Type Information Element whose value was not valid for the configured link maintenance protocol. noErrorSinceReset: no errors have been detected since the last cold start or warm start." ::= { frErrEntry 2 } frErrData OBJECT-TYPE SYNTAX OCTET STRING (SIZE(1..1600)) MAX-ACCESS read-only STATUS current DESCRIPTION "An octet string containing as much of the error packet as possible. As a minimum, it must contain the Q.922 Address or as much as was delivered. It is desirable to include all header and demultiplexing information." ::= { frErrEntry 3 } Brown & Baker Standards Track [Page 24]
RFC 2115 Frame Relay DTE MIB September 1997 frErrTime OBJECT-TYPE SYNTAX TimeStamp MAX-ACCESS read-only STATUS current DESCRIPTION "The value of sysUpTime at which the error was detected." ::= { frErrEntry 4 } frErrFaults OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of times the interface has gone down since it was initialized." ::= { frErrEntry 5 } frErrFaultTime OBJECT-TYPE SYNTAX TimeStamp MAX-ACCESS read-only STATUS current DESCRIPTION "The value of sysUpTime at the time when the interface was taken down due to excessive errors. Excessive errors is defined as the time when a DLCMI exceeds the frDlcmiErrorThreshold number of errors within frDlcmiMonitoredEvents. See FrDlcmiEntry for further details." ::= { frErrEntry 6 } -- -- Frame Relay Trap Control frameRelayTrapControl OBJECT IDENTIFIER ::= { frameRelayDTE 4 } -- the following highly unusual OID is as it is for compatibility -- with RFC 1315, the SNMP V1 predecessor of this document. frameRelayTraps OBJECT IDENTIFIER ::= { frameRelayDTE 0 } Brown & Baker Standards Track [Page 25]
RFC 2115 Frame Relay DTE MIB September 1997 frTrapState OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "This variable indicates whether the system produces the frDLCIStatusChange trap." DEFVAL { disabled } ::= { frameRelayTrapControl 1 } frTrapMaxRate OBJECT-TYPE SYNTAX Integer32 (0..3600000) MAX-ACCESS read-write STATUS current DESCRIPTION "This variable indicates the number of milliseconds that must elapse between trap emissions. If events occur more rapidly, the impementation may simply fail to trap, or may queue traps until an appropriate time." DEFVAL { 0 } -- no minimum elapsed period is specified ::= { frameRelayTrapControl 2 } -- Data Link Connection Management Interface Related Traps frDLCIStatusChange NOTIFICATION-TYPE OBJECTS { frCircuitState } STATUS current DESCRIPTION "This trap indicates that the indicated Virtual Circuit has changed state. It has either been created or invalidated, or has toggled between the active and inactive states. If, however, the reason for the state change is due to the DLCMI going down, per-DLCI traps should not be generated." ::= { frameRelayTraps 1 } -- conformance information frConformance OBJECT IDENTIFIER ::= { frameRelayDTE 6 } frGroups OBJECT IDENTIFIER ::= { frConformance 1 } frCompliances OBJECT IDENTIFIER ::= { frConformance 2 } -- compliance statements Brown & Baker Standards Track [Page 26]
RFC 2115 Frame Relay DTE MIB September 1997 frCompliance MODULE-COMPLIANCE STATUS current DESCRIPTION "The compliance statement " MODULE -- this module MANDATORY-GROUPS { frPortGroup, frCircuitGroup } GROUP frErrGroup DESCRIPTION "This optional group is used for debugging Frame Relay Systems." GROUP frTrapGroup DESCRIPTION "This optional group is used for the management of asynchronous notifications by Frame Relay Systems." GROUP frNotificationGroup DESCRIPTION "This optional group defines the asynchronous notifications generated by Frame Relay Systems." OBJECT frDlcmiRowStatus MIN-ACCESS read-only DESCRIPTION "Row creation is not required for the frDlcmiTable." OBJECT frCircuitRowStatus MIN-ACCESS read-only DESCRIPTION "Row creation is not required for the frCircuitTable." ::= { frCompliances 1 } frCompliance0 MODULE-COMPLIANCE STATUS current DESCRIPTION "The compliance statement for objects and the trap defined in RFC 1315." MODULE -- this module MANDATORY-GROUPS { frPortGroup0, frCircuitGroup0 } GROUP frErrGroup0 DESCRIPTION "This optional group is used for debugging Frame Relay Systems." Brown & Baker Standards Track [Page 27]
RFC 2115 Frame Relay DTE MIB September 1997 GROUP frTrapGroup0 DESCRIPTION "This optional group is used for the management of asynchronous notifications by Frame Relay Systems." GROUP frNotificationGroup DESCRIPTION "This optional group defines the asynchronous notifications generated by Frame Relay Systems." ::= { frCompliances 2 } -- units of conformance frPortGroup OBJECT-GROUP OBJECTS { frDlcmiIfIndex, frDlcmiState, frDlcmiAddress, frDlcmiAddressLen, frDlcmiPollingInterval, frDlcmiFullEnquiryInterval, frDlcmiErrorThreshold, frDlcmiMonitoredEvents, frDlcmiMaxSupportedVCs, frDlcmiMulticast, frDlcmiStatus, frDlcmiRowStatus } STATUS current DESCRIPTION "The objects necessary to control the Link Management Interface for a Frame Relay Interface as well as maintain the error statistics on this interface." ::= { frGroups 1 } frCircuitGroup OBJECT-GROUP OBJECTS { frCircuitIfIndex, frCircuitDlci, frCircuitState, frCircuitReceivedFECNs, frCircuitReceivedBECNs, frCircuitSentFrames, frCircuitSentOctets, frCircuitReceivedFrames, frCircuitReceivedOctets, frCircuitCreationTime, frCircuitLastTimeChange, frCircuitCommittedBurst, frCircuitExcessBurst, frCircuitThroughput, frCircuitMulticast, frCircuitType, frCircuitDiscards, frCircuitReceivedDEs, frCircuitSentDEs, frCircuitLogicalIfIndex, frCircuitRowStatus } STATUS current DESCRIPTION "The objects necessary to control the Virtual Circuits layered onto a Frame Relay Interface." ::= { frGroups 2 } Brown & Baker Standards Track [Page 28]
RFC 2115 Frame Relay DTE MIB September 1997 frTrapGroup OBJECT-GROUP OBJECTS { frTrapState, frTrapMaxRate } STATUS current DESCRIPTION "The objects necessary to control a Frame Relay Interface's notification messages." ::= { frGroups 3 } frErrGroup OBJECT-GROUP OBJECTS { frErrIfIndex, frErrType, frErrData, frErrTime, frErrFaults, frErrFaultTime } STATUS current DESCRIPTION "Objects designed to assist in debugging Frame Relay Interfaces." ::= { frGroups 4 } frNotificationGroup NOTIFICATION-GROUP NOTIFICATIONS { frDLCIStatusChange } STATUS current DESCRIPTION "Traps which may be used to enhance event driven management of the interface." ::= { frGroups 5 } frPortGroup0 OBJECT-GROUP OBJECTS { frDlcmiIfIndex, frDlcmiState, frDlcmiAddress, frDlcmiAddressLen, frDlcmiPollingInterval, frDlcmiFullEnquiryInterval, frDlcmiErrorThreshold, frDlcmiMonitoredEvents, frDlcmiMaxSupportedVCs, frDlcmiMulticast } STATUS current DESCRIPTION "The objects necessary to control the Link Management Interface for a Frame Relay Interface as well as maintain the error statistics on this interface from RFC 1315." ::= { frGroups 6 } frCircuitGroup0 OBJECT-GROUP OBJECTS { frCircuitIfIndex, frCircuitDlci, frCircuitState, frCircuitReceivedFECNs, frCircuitReceivedBECNs, frCircuitSentFrames, frCircuitSentOctets, Brown & Baker Standards Track [Page 29]
RFC 2115 Frame Relay DTE MIB September 1997 frCircuitReceivedFrames, frCircuitReceivedOctets, frCircuitCreationTime, frCircuitLastTimeChange, frCircuitCommittedBurst, frCircuitExcessBurst, frCircuitThroughput } STATUS current DESCRIPTION "The objects necessary to control the Virtual Circuits layered onto a Frame Relay Interface from RFC 1315." ::= { frGroups 7 } frErrGroup0 OBJECT-GROUP OBJECTS { frErrIfIndex, frErrType, frErrData, frErrTime } STATUS current DESCRIPTION "Objects designed to assist in debugging Frame Relay Interfaces from RFC 1315." ::= { frGroups 8 } frTrapGroup0 OBJECT-GROUP OBJECTS { frTrapState } STATUS current DESCRIPTION "The objects necessary to control a Frame Relay Interface's notification messages from RFC 1315." ::= { frGroups 9 } END 7. Security Issues Security issues for this MIB are entirely covered by the SNMP Security Architecture, and have not been expanded within the contents of this MIB. 8. Acknowledgments This document was originally produced by the IP Over Large Public Data Networks (IPLPDN) Working Group, and has since been carried on in the PPP Working Group, sort of. Currently, the Ion Working Group is its host. Special thanks to James Watt of Newbridge Networks for his fine suggestions and pastable text. Brown & Baker Standards Track [Page 30]
RFC 2115 Frame Relay DTE MIB September 1997 9. Authors' Addresses Caralyn Brown Cadia Networks, Inc. 1 Corporate Dirve Andover, Massachusetts 01810 Telephone: +1 508 689 2400 x133 E-Mail: cbrown@cadia.com Fred Baker Cisco Systems 519 Lado Drive Santa Barbara, California 93111 Telephone +1 408 526 4257 E-Mail: fred@cisco.com 10. References [1] SNMPv2 Working Group, Case, J., McCloghrie, K., Rose, M., and S. Waldbusser, "Structure of Management Information for Version 2 of the Simple Network Management Protocol (SNMPv2)", RFC 1902, January 1996. [2] McCloghrie, K., and M. Rose, Editors, "Management Information Base for Network Management of TCP/IP-based internets: MIB-II", STD 17, RFC 1213, Hughes LAN Systems, Performance Systems International, March 1991. [3] Case, J., Fedor, M., Schoffstall, M., and J. Davin. " A Simple Network Management Protocol (SNMP)", STD 15, RFC 1157, SNMP Research, Performance Systems International, MIT Lab for Computer Science, May 1990. [4] SNMPv2 Working Group, Case, J., McCloghrie, K., Rose, M., and S. Waldbusser, "Protocol Operations for Version 2 of the Simple Network Management Protocol (SNMPv2)", RFC 1905, January 1996. [5] McCloghrie, K. and F. Kastenholz, "Evolution of the Interfaces Group of MIB-II", RFC 1573, Hughes LAN Systems, FTP Software, January 1994. [6] T. Bradley, C. Brown, A. Malis, "Multiprotocol Interconnect over Frame Relay", RFC 1490, 07/26/1993. [7] International Telegraph and Telephone Consultative Committee, "ISDN Data Link Layer Specification for Frame Mode Bearer Services", CCITT Recommendation Q.922, 19 Brown & Baker Standards Track [Page 31]
RFC 2115 Frame Relay DTE MIB September 1997
April 1991.
[8] American National Standard For Telecommunications -
Integrated Services Digital Network - Frame Relay Bearer
Service - Architectural Framework and Service
Description, ANSI T1.606-1991, 18 June 1991.
[9] American National Standard For Telecommunications -
Integrated Services Digital Network - Digital Subscriber
Signalling System No. 1 - Signaling Specification for
Frame Relay Bearer Service, ANSI T1.617-1991, 18 June
1991.
[10] American National Standard For Telecommunications -
Integrated Services Digital Network - Core Aspects of
Frame Protocol for Use with Frame Relay Bearer Service,
ANSI T1.618-1991, 18 June 1991.
Brown & Baker Standards Track [Page 32]
mirror server hosted at Truenetwork, Russian Federation.