Network Working Group B. Aboba
Request for Comments: 3162 Microsoft
Category: Standards Track G. Zorn
Cisco Systems
D. Mitton
Circular Logic UnLtd.
August 2001
RADIUS and IPv6
Status of this Memo
This document specifies an Internet standards track protocol for the
Internet community, and requests discussion and suggestions for
improvements. Please refer to the current edition of the "Internet
Official Protocol Standards" (STD 1) for the standardization state
and status of this protocol. Distribution of this memo is unlimited.
Copyright Notice
Copyright (C) The Internet Society (2001). All Rights Reserved.
Abstract
This document specifies the operation of RADIUS (Remote
Authentication Dial In User Service) when run over IPv6 as well as
the RADIUS attributes used to support IPv6 network access.
1. Introduction
This document specifies the operation of RADIUS [4]-[8] over IPv6
[13] as well as the RADIUS attributes used to support IPv6 network
access.
Note that a NAS sending a RADIUS Access-Request may not know a-priori
whether the host will be using IPv4, IPv6, or both. For example,
within PPP, IPv6CP [11] occurs after LCP, so that address assignment
will not occur until after RADIUS authentication and authorization
has completed.
Therefore it is presumed that the IPv6 attributes described in this
document MAY be sent along with IPv4-related attributes within the
same RADIUS message and that the NAS will decide which attributes to
use. The NAS SHOULD only allocate addresses and prefixes that the
client can actually use, however. For example, there is no need for
Aboba, et al. Standards Track [Page 1]
RFC 3162 RADIUS and IPv6 August 2001 the NAS to reserve use of an IPv4 address for a host that only supports IPv6; similarly, a host only using IPv4 or 6to4 [12] does not require allocation of an IPv6 prefix. The NAS can provide IPv6 access natively, or alternatively, via other methods such as IPv6 within IPv4 tunnels [15] or 6over4 [14]. The choice of method for providing IPv6 access has no effect on RADIUS usage per se, although if it is desired that an IPv6 within IPv4 tunnel be opened to a particular location, then tunnel attributes should be utilized, as described in [6], [7]. 1.1. Requirements language In this document, the key words "MAY", "MUST, "MUST NOT", "optional", "recommended", "SHOULD", and "SHOULD NOT", are to be interpreted as described in [1]. 2. Attributes 2.1. NAS-IPv6-Address Description This Attribute indicates the identifying IPv6 Address of the NAS which is requesting authentication of the user, and SHOULD be unique to the NAS within the scope of the RADIUS server. NAS- IPv6-Address is only used in Access-Request packets. NAS-IPv6- Address and/or NAS-IP-Address MAY be present in an Access-Request packet; however, if neither attribute is present then NAS- Identifier MUST be present. A summary of the NAS-IPv6-Address Attribute format is shown below. The fields are transmitted from left to right. 0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Type | Length | Address +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ Address +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ Address +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ Address +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ Address | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ Aboba, et al. Standards Track [Page 2]
RFC 3162 RADIUS and IPv6 August 2001 Type 95 for NAS-IPv6-Address Length 18 Address The Address field is 16 octets. 3.2. Framed-Interface-Id Description This Attribute indicates the IPv6 interface identifier to be configured for the user. It MAY be used in Access-Accept packets. If the Interface-Identifier IPv6CP option [11] has been successfully negotiated, this Attribute MUST be included in an Access-Request packet as a hint by the NAS to the server that it would prefer that value. It is recommended, but not required, that the server honor the hint. A summary of the Framed-Interface-Id Attribute format is shown below. The fields are transmitted from left to right. 0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Type | Length | Interface-Id +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ Interface-Id +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ Interface-Id | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ Type 96 for Framed-Interface-Id Length 10 Interface-Id The Interface-Id field is 8 octets. Aboba, et al. Standards Track [Page 3]
RFC 3162 RADIUS and IPv6 August 2001 2.3. Framed-IPv6-Prefix Description This Attribute indicates an IPv6 prefix (and corresponding route) to be configured for the user. It MAY be used in Access-Accept packets, and can appear multiple times. It MAY be used in an Access-Request packet as a hint by the NAS to the server that it would prefer these prefix(es), but the server is not required to honor the hint. Since it is assumed that the NAS will plumb a route corresponding to the prefix, it is not necessary for the server to also send a Framed-IPv6-Route attribute for the same prefix. A summary of the Framed-IPv6-Prefix Attribute format is shown below. The fields are transmitted from left to right. 0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Type | Length | Reserved | Prefix-Length | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ Prefix +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ Prefix +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ Prefix +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ Prefix | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ Type 97 for Framed-IPv6-Prefix Length At least 4 and no larger than 20. Reserved This field, which is reserved and MUST be present, is always set to zero. Prefix-Length The length of the prefix, in bits. At least 0 and no larger than 128. Aboba, et al. Standards Track [Page 4]
RFC 3162 RADIUS and IPv6 August 2001 Prefix The Prefix field is up to 16 octets in length. Bits outside of the Prefix-Length, if included, must be zero. 2.4. Login-IPv6-Host Description This Attribute indicates the system with which to connect the user, when the Login-Service Attribute is included. It MAY be used in Access-Accept packets. It MAY be used in an Access- Request packet as a hint to the server that the NAS would prefer to use that host, but the server is not required to honor the hint. A summary of the Login-IPv6-Host Attribute format is shown below. The fields are transmitted from left to right. 0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Type | Length | Address +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ Address +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ Address +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ Address +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ Address | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ Type 98 for Login-IPv6-Host Length 18 Aboba, et al. Standards Track [Page 5]
RFC 3162 RADIUS and IPv6 August 2001 Address The Address field is 16 octets in length. The value 0xFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFF indicates that the NAS SHOULD allow the user to select an address or name to be connected to. The value 0 indicates that the NAS SHOULD select a host to connect the user to. Other values indicate the address the NAS SHOULD connect the user to. 2.5. Framed-IPv6-Route Description This Attribute provides routing information to be configured for the user on the NAS. It is used in the Access-Accept packet and can appear multiple times. A summary of the Framed-IPv6-Route Attribute format is shown below. The fields are transmitted from left to right. 0 1 2 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+- | Type | Length | Text ... +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+- Type 99 for Framed-IPv6-Route Length >=3 Text The Text field is one or more octets, and its contents are implementation dependent. The field is not NUL (hex 00) terminated. It is intended to be human readable and MUST NOT affect operation of the protocol. For IPv6 routes, it SHOULD contain a destination prefix optionally followed by a slash and a decimal length specifier stating how many high order bits of the prefix to use. That is followed by a space, a gateway address, a space, and one or more metrics (encoded in decimal) separated by spaces. Prefixes and addresses are formatted as described in [16]. For example, "2000:0:0:106::/64 2000::106:a00:20ff:fe99:a998 1". Aboba, et al. Standards Track [Page 6]
RFC 3162 RADIUS and IPv6 August 2001 Whenever the gateway address is the IPv6 unspecified address the IP address of the user SHOULD be used as the gateway address. The unspecified address can be expressed in any of the acceptable formats described in [16]. For example, "2000:0:0:106::/64 :: 1". 2.6. Framed-IPv6-Pool Description This Attribute contains the name of an assigned pool that SHOULD be used to assign an IPv6 prefix for the user. If a NAS does not support multiple prefix pools, the NAS MUST ignore this Attribute. A summary of the Framed-IPv6-Pool Attribute format is shown below. The fields are transmitted from left to right. 0 1 2 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Type | Length | String... +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ Type 100 for Framed-IPv6-Pool Length >= 3 String The string field contains the name of an assigned IPv6 prefix pool configured on the NAS. The field is not NUL (hex 00) terminated. 3. Table of Attributes The following table provides a guide to which attributes may be found in which kinds of packets, and in what quantity. Request Accept Reject Challenge Accounting # Attribute Request 0-1 0 0 0 0-1 95 NAS-IPv6-Address 0-1 0-1 0 0 0-1 96 Framed-Interface-Id 0+ 0+ 0 0 0+ 97 Framed-IPv6-Prefix 0+ 0+ 0 0 0+ 98 Login-IPv6-Host 0 0+ 0 0 0+ 99 Framed-IPv6-Route 0 0-1 0 0 0-1 100 Framed-IPv6-Pool Aboba, et al. Standards Track [Page 7]
RFC 3162 RADIUS and IPv6 August 2001 4. References [1] Bradner, S., "Key words for use in RFCs to Indicate Requirement Levels", BCP 14, RFC 2119, March, 1997. [2] Yergeau, F., "UTF-8, a transformation format of Unicode and ISO 10646", RFC 2044, October 1996. [3] Aboba, B. and J. Vollbrecht, "Proxy Chaining and Policy Implementation in Roaming", RFC 2607, June 1999. [4] Rigney, C., Rubens, A., Simpson, W. and S. Willens, "Remote Authentication Dial In User Service (RADIUS)", RFC 2865, June 2000. [5] Rigney, C., "RADIUS Accounting", RFC 2866, June 2000. [6] Zorn, G., Mitton, D. and B. Aboba, "RADIUS Accounting Modifications for Tunnel Protocol Support", RFC 2867, June 2000. [7] Zorn, G., Leifer, D., Rubens, A., Shriver, J., Holdrege, M. and I. Goyret, "RADIUS Attributes for Tunnel Protocol Support", RFC 2868, June 2000. [8] Rigney, C., Willats, W. and P. Calhoun, "RADIUS Extensions", RFC 2869, June 2000. [9] Kent S. and R. Atkinson, "Security Architecture for the Internet Protocol", RFC 2401, November 1998. [10] Alvestrand, H. and T. Narten, "Guidelines for Writing an IANA Considerations Section in RFCs", BCP 26, RFC 2434, October 1998. [11] Haskin, D. and E. Allen, "IP Version 6 over PPP", RFC 2472, December 1998. [12] Carpenter, B. and K. Moore, "Connection of IPv6 Domains via IPv4 Clouds", RFC 3056, February 2001. [13] Deering, S. and R. Hinden, "Internet Protocol, Version 6 (IPv6) Specification", RFC 2460, December 1998. [14] Carpenter, B. and C. Jung, "Transmission of IPv6 over IPv4 Domains without Explicit Tunnels", RFC 2529, March 1999. Aboba, et al. Standards Track [Page 8]
RFC 3162 RADIUS and IPv6 August 2001 [15] Gilligan, R. and E. Nordmark, "Transition Mechanisms for IPv6 Hosts and Routers", RFC 2893, August 2000. [16] Hinden, R. and S. Deering, "IP Version 6 Addressing Architecture", RFC 2373, July 1998. 5. Security Considerations This document describes the use of RADIUS for the purposes of authentication, authorization and accounting in IPv6-enabled networks. In such networks, the RADIUS protocol may run either over IPv4 or over IPv6. Known security vulnerabilities of the RADIUS protocol are described in [3], [4] and [8]. Since IPSEC [9] is mandatory to implement for IPv6, it is expected that running RADIUS implementations supporting IPv6 will typically run over IPSEC. Where RADIUS is run over IPSEC and where certificates are used for authentication, it may be desirable to avoid management of RADIUS shared secrets, so as to leverage the improved scalability of public key infrastructure. Within RADIUS, a shared secret is used for hiding of attributes such as User-Password [4] and Tunnel-Password [7]. In addition, the shared secret is used in computation of the Response Authenticator [4], as well as the Message-Authenticator attribute [8]. Therefore, in RADIUS a shared secret is used to provide confidentiality as well as integrity protection and authentication. As a result, only use of IPSEC ESP with a non-null transform can provide security services sufficient to substitute for RADIUS application-layer security. Therefore, where IPSEC AH or ESP null is used, it will typically still be necessary to configure a RADIUS shared secret. However, where RADIUS is run over IPSEC ESP with a non-null transform, the secret shared between the NAS and the RADIUS server MAY NOT be configured. In this case, a shared secret of zero length MUST be assumed. Aboba, et al. Standards Track [Page 9]
RFC 3162 RADIUS and IPv6 August 2001 6. IANA Considerations This document requires the assignment of six new RADIUS attribute numbers for the following attributes: NAS-IPv6-Address Framed-Interface-Id Framed-IPv6-Prefix Login-IPv6-Host Framed-IPv6-Route Framed-IPv6-Pool See section 3 for the registered list of numbers. 7. Acknowledgments The authors would like to acknowledge Jun-ichiro itojun Hagino of IIJ Research Laboratory, Darran Potter of Cisco and Carl Rigney of Lucent for contributions to this document. Aboba, et al. Standards Track [Page 10]
RFC 3162 RADIUS and IPv6 August 2001 8. Authors' Addresses Bernard Aboba Microsoft Corporation One Microsoft Way Redmond, WA 98052 Phone: +1 425 936 6605 Fax: +1 425 936 7329 EMail: bernarda@microsoft.com Glen Zorn Cisco Systems, Inc. 500 108th Avenue N.E., Suite 500 Bellevue, WA 98004 Phone: +1 425 471 4861 EMail: gwz@cisco.com Dave Mitton Circular Logic UnLtd. 733 Turnpike Street #154 North Andover, MA 01845 Phone: 978 683-1814 Email: david@mitton.com Aboba, et al. Standards Track [Page 11]
RFC 3162 RADIUS and IPv6 August 2001
Full Copyright Statement
Copyright (C) The Internet Society (2001). All Rights Reserved.
This document and translations of it may be copied and furnished to
others, and derivative works that comment on or otherwise explain it
or assist in its implementation may be prepared, copied, published
and distributed, in whole or in part, without restriction of any
kind, provided that the above copyright notice and this paragraph are
included on all such copies and derivative works. However, this
document itself may not be modified in any way, such as by removing
the copyright notice or references to the Internet Society or other
Internet organizations, except as needed for the purpose of
developing Internet standards in which case the procedures for
copyrights defined in the Internet Standards process must be
followed, or as required to translate it into languages other than
English.
The limited permissions granted above are perpetual and will not be
revoked by the Internet Society or its successors or assigns.
This document and the information contained herein is provided on an
"AS IS" basis and THE INTERNET SOCIETY AND THE INTERNET ENGINEERING
TASK FORCE DISCLAIMS ALL WARRANTIES, EXPRESS OR IMPLIED, INCLUDING
BUT NOT LIMITED TO ANY WARRANTY THAT THE USE OF THE INFORMATION
HEREIN WILL NOT INFRINGE ANY RIGHTS OR ANY IMPLIED WARRANTIES OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.
Acknowledgement
Funding for the RFC Editor function is currently provided by the
Internet Society.
Aboba, et al. Standards Track [Page 12]
mirror server hosted at Truenetwork, Russian Federation.