Network Working Group D. Rawlins
Request for Comments: 3571 MCI
Category: Informational A. Kulkarni
Intel
K. Chan
Nortel Networks
M. Bokaemper
Juniper Networks
D. Dutt
Cisco
August 2003
Framework Policy Information Base for Usage Feedback
Status of this Memo
This memo provides information for the Internet community. It does
not specify an Internet standard of any kind. Distribution of this
memo is unlimited.
Copyright Notice
Copyright (C) The Internet Society (2003). All Rights Reserved.
Abstract
This document describes a portion of the Policy Information Base
(PIB) to control policy usage collection and reporting in a device.
The provisioning classes specified here allow a Policy Decision Point
(PDP) to select which policy objects should collect usage
information, what information should be collected and when it should
be reported.
This PIB requires the presence of other PIBs (defined elsewhere) that
provide the policy objects from which usage information is collected.
Rawlins, et al. Informational [Page 1]
RFC 3571 Framework Feedback PIB August 2003 Table of Contents 1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . . 2 2. General Concepts . . . . . . . . . . . . . . . . . . . . . . . 3 2.1. Selection, Usage and Linkage Policies. . . . . . . . . . 3 2.2. Normal Operations. . . . . . . . . . . . . . . . . . . . 4 2.2.1. Connection Establishment and Initial Configuration Request. . . . . . . . . . . . . . 4 2.2.2. Unsolicited Reports - Periodic Reporting . . . . 5 2.2.3. Unsolicited Reports - Reporting Conditions . . . 5 2.2.4. Solicited Reports. . . . . . . . . . . . . . . . 6 2.2.5. Resuming and Suspending Periodic Feedback Reporting. . . . . . . . . . . . . . . . . . . . 6 2.2.6. Failover . . . . . . . . . . . . . . . . . . . . 6 2.3. Usage Policy and Under-specified Selection Criteria. . . 7 3. Summary of the Feedback Framework Policy Information Base. . . 8 3.1. SPPI ACCESS Clause Report-Only . . . . . . . . . . . . . 8 3.2. Usage32 and Usage64 Textual Conventions. . . . . . . . . 8 3.3. Feedback Groups and PRCs . . . . . . . . . . . . . . . . 9 3.3.1. Feedback Action. . . . . . . . . . . . . . . . . 9 3.3.2. Feedback Action List . . . . . . . . . . . . . . 10 3.3.3. Feedback Linkage Capability. . . . . . . . . . . 10 3.3.4. Feedback Linkage . . . . . . . . . . . . . . . . 10 3.3.5. Feedback Traffic Statistics Threshold. . . . . . 10 3.3.6. Feedback Traffic . . . . . . . . . . . . . . . . 10 3.3.7. Feedback Interface Traffic . . . . . . . . . . . 11 3.3.8. Feedback RoleCombo Filter Selection. . . . . . . 11 4. The Feedback Framework PIB Module. . . . . . . . . . . . . . . 11 5. Security Considerations. . . . . . . . . . . . . . . . . . . . 31 6. IANA Considerations. . . . . . . . . . . . . . . . . . . . . . 32 7. Acknowledgements . . . . . . . . . . . . . . . . . . . . . . . 32 8. References . . . . . . . . . . . . . . . . . . . . . . . . . . 32 8.1. Normative References . . . . . . . . . . . . . . . . . . 32 8.2. Informational References . . . . . . . . . . . . . . . . 33 9. Authors' Addresses . . . . . . . . . . . . . . . . . . . . . . 34 10. Full Copyright Statement . . . . . . . . . . . . . . . . . . . 35 1. Introduction The Framework of Common Open Policy Service with Policy Provisioning (COPS-PR) Usage Feedback describes the overall approach to policy usage monitoring and reporting. This document defines the specific Policy Information Base (PIB) framework for policy usage feedback. The policy classes for monitoring and reporting policy usage feedback, as well as policy classes for controlling reporting intervals, suspension, resumption and solicitation are defined. Rawlins, et al. Informational [Page 2]
RFC 3571 Framework Feedback PIB August 2003 Conventions Used in this Document The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT", "SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY" and "OPTIONAL" in this document are to be interpreted as described in [RFC2119]. 2. General Concepts 2.1. Selection, Usage and Linkage Policies There are three basic types of policies used to define what the PEP is to monitor, record and report. These are the selection criteria policy, the usage policy and the feedback report linkage policy. The selection criteria policy is installed by the PDP. It defines the conditions used by the PEP to monitor and record a usage policy. The selection criteria policy may only be used for defining usage feedback selection criteria. However, a more general case is a policy that already exists for policy enforcement that may also be used for specifying feedback usage selection criteria. An example of this is the frwkRoleCombo instance, which may be used in defining QoS enforcement policies, but may also be used to specify conditions on which to base usage - i.e. count the number of packets meeting the criterion of an interface capability set name and role combination. The usage policy defines what attributes are recorded by the PEP. These policies have an ACCESS clause of 'report-only'. Generally, the usage policies specify counts related to a specific action such as a packet being dropped. The feedback framework PIB defines two usage policy classes, frwkFeedbackTraffic and frwkFeedbackIfTraffic. Usage PRCs may be generic, collecting basic statistics, or they may be specific to a particular usage. The PDP decides which PRC(s) best suit(s) its requirements. The PEP may support only one usage feedback PRC, in which case all statistics are gathered using instances of that PRC. Alternatively, the PEP may support multiple usage feedback PRCs. The PDP then decides which PRC to associate with a particular selection criterion. A usage feedback policy and selection policy are tightly associated with one another. A third policy, the frwkFeedbackLinkTable, is used to associate, or provide a linkage for the selection and usage policies. The frwkFeedbackLinkTable also specifies when to report the usage feedback. The frwkFeedbackLinkTable entry permits the same selection criteria instance to be re-used for various usage feedback policies. The frwkFeedbackLinkTable contains the value of the selection criteria instance as well as the value of the usage feedback PRC. Rawlins, et al. Informational [Page 3]
RFC 3571 Framework Feedback PIB August 2003 ----------------- ------------------ ----------------- | | | | | | | Select Criteria | |Linkage Instance | |Usage Instance | | | |-instance ID | |- instance ID | | -instance ID |<--|-PRID of selection|--->|- PRID of Linkage| | -conditions... | |-PRC of usage | |- counts... | | | | | | | ----------------- ------------------ ----------------- Figure 1 Figure 1 illustrates the relationship between the selection criteria, linkage and usage policies. The PDP is not aware of the instance identifier of the usage feedback policy when installing the selection criteria and feedback linkage policies. The usage feedback policy is instantiated on the PEP by the installation of a feedback report linkage and the PEP designates the instance identifier. The usage feedback policy class always contains an attribute of type ReferenceId that contains the instance value of the associated frwkFeedbackLinkTable instance installed by the PDP. An example of this is the attribute frwkFeedbackTrafficLinkRef. 2.2. Normal Operations 2.2.1. Connection Establishment and Initial Configuration Request The Accounting Timer object in the COPS Connection Accept message contains the minimum number of seconds between reporting intervals as described in [COPS] and [FEEDBACKFWK]. This is used as the basic unit of measurement in defining intervals for specific usage policies with the frwkFeedbackLinkInterval attribute. The PEP notifies the PDP of the selection criteria policy classes and usage policy classes it supports during the initial request for configuration data using frwkPRCSupport instances [FR-PIB]. The PEP also indicates whether it supports the frwkFeedbackLinkTable as well. The PDP responds to the initial request for configuration with a DECISION that installs policies. The PDP may also specify maximum reporting intervals associated with each of the usage policies. This is done with the frwkFeedbackLinkInterval attribute in the frwkFeedbackLink class. It may also specify reporting thresholds by including an instance of a threshold class (e.g. frwkFeedbackTrafficThreshold) in the decision. The PEP monitors and records the usage per the conditions defined by its associated selection criteria policy. Periodically the PEP reports the usage Rawlins, et al. Informational [Page 4]
RFC 3571 Framework Feedback PIB August 2003 with a REPORT message or provides a REPORT when solicited by the PDP. The PDP solicits usage feedback with the frwkFeedbackActionIndicator attribute of the frwkFeedbackAction class. 2.2.2. Unsolicited Reports - Periodic Reporting Reporting may be periodic in nature and unsolicited. The intervals at which the unsolicited reports are provided by the PEP are defined in the specific Linkage policies. The defined intervals are based on the number of seconds specified by the PDP in the ACCT Timer value. The PDP may specify that the associated usage instance be included in a periodic unsolicited report only if the threshold is reached and/or if the usage value has changed from the previous reporting interval. There are cases when the PEP must supply unsolicited feedback reports that may not fall on an interval boundary. The PEP MUST provide an unsolicited REPORT containing all defined usage instances just prior to the PEP issuing a Delete Request State and just prior to the PEP de-activating a PIB instance context. 2.2.3. Unsolicited Reports - Reporting Conditions Periodic unsolicited reports for individual usage feedback instances can be suppressed by specifying additional conditions in the frwkFeedbackLink instances. Supported conditions are: ChangeOnly If this flag is set in the frwkFeedbackLinkFlags attribute, the associated usage instance is only included in a periodic unsolicited report if its value changed since the last unsolicited report. Threshold If this flag is set in the frwkFeedbackLinkFlags attribute, the associated usage instance is only included in a periodic unsolicited report if the threshold condition referenced in the frwkLinkThreshold field evaluates successfully for the associated usage instance. Both conditions can be combined in one frwkFeedbackLinkUsage object. In this case, both conditions need to succeed for the usage instance to be reported. Unsolicited reports triggered by a Delete Request State or the deactivation of a PIB instance are not subject to these conditions - all usage objects must be included in these cases. Rawlins, et al. Informational [Page 5]
RFC 3571 Framework Feedback PIB August 2003 2.2.4. Solicited Reports The PDP may solicit policy usage feedback by issuing an unsolicited Decision containing the frwkFeedbackActionIndicator set to `solicitReport'. The PEP is to provide a solicited REPORT feedback containing usage feedback. The PEP shall continue to provide periodic feedback at the specified intervals established at client connection acceptance. The reporting conditions (ChangeOnly and Threshold) do not affect solicited reports - all requested usage instances must be included. 2.2.5. Resuming and Suspending Periodic Feedback Reporting The PDP may suspend usage monitoring and tracking at the PEP with the frwkFeedbackActionIndicator set to 'suspendMonitoringAndReports'. The PEP must stop tracking usage information and must not issue any feedback reports. The PDP may only suspend feedback reporting by setting the ActionIndicator to 'suspendReports'. The PEP must cease sending unsolicited reports but is to continue monitoring and tracking usage. The PDP may resume the sending of feedback reports and may resume usage monitoring by setting the ActionIndicator to 'resume'. The PDP may suspend or resume all usage instances or the PDP may specify one or more instances that are to be suspended or resumed. The frwkFeedbackActionList attribute contains a tag identifier that references a list of one or more frwkFeedbackActionList instances. The PDP may halt usage monitoring, tracking and reporting of usage policies by removing the associated Linkage entry. 2.2.6. Failover In the event that the connection is lost between the PEP and PDP, the PEP continues to track usage information as long as it continues to operate with the installed policy. When the locally installed policy at the PEP expires, the usage policy data also expires. Upon successful reconnection where the PEP is still caching policy, the PDP indicates to the PEP that the PEP may resume sending of the COPS accounting type report messages. The PDP does this by issuing an unsolicited decision containing the frwkFeedbackResumeIndicator set to 'resume'. The PEP should resume reporting at the next appropriate feedback interval established upon the acceptance of the re-connection. The PDP is aware of the request state Handle(s) and Rawlins, et al. Informational [Page 6]
RFC 3571 Framework Feedback PIB August 2003 the supported PRCs either through the state synchronization mechanism or because the PDP considers itself synchronized with the PEP upon reconnection. 2.3. Usage Policy and Under-specified Selection Criteria Some of the usage policy objects created in the PEP with COPS-PR can be used by the PEP multiple times - they effectively act as templates for the objects created by the PEP. COPS-PR only has the identity (OID) of the object that is shared between all the assignments the PEP created. However it is desirable to collect usage information for each of the derived objects individually. This capability is achieved in the feedback framework PIB by distributing additional information to qualify a specific assignment of an object between the selection criteria PRC and the feedback usage PRC. A selection criteria PRC that refers to a shared object, but contains no qualifying information, selects all of the object's assignments. Such a selection criteria PRC SHOULD be combined with a feedback usage PRC that includes all the necessary information to identify a specific assignment - a single selection criteria policy can then result in the generation of many feedback usage objects, one for each derived object. If the selection criteria PRC contains all the required qualifying attributes for a specific assignment, it is combined with a feedback usage PRC that only contains the desired metrics but no additional attributes. Example: A frwkRoleCombo instance may be used as a selection criteria, identifying a set of interfaces through their role combination and capability set. If it is desired to get per-interface traffic statistics, the usage PRC has to include an additional attribute to qualify the specific interface. This could be achieved by linking the frwkFeedbackIfTraffic class with a frwkRoleCombo instance in a frwkFeedbackLink instance. Multiple frwkFeedbackIfTraffic instances will be created by the PEP, one for each interface selected by the frwkRoleCombo instance. The frwkFeedbackIfTraffic class contains the frwkFeedbackIfTrafficIfIndex attribute that allows the PDP to identify each interface's individual counters when the PEP reports the frwkFeedbackIfTraffic instances. Rawlins, et al. Informational [Page 7]
RFC 3571 Framework Feedback PIB August 2003 If traffic usage collection is only desired for an individual interface, a selection criteria should be used that qualifies the interface completely, for example a frwkIfRoleCombo instance. In this case, it can be linked to the usage class that has no additional qualifying attributes, frwkFeedbackTraffic. 3. Summary of the Feedback Framework Policy Information Base 3.1. SPPI ACCESS Clause Report-Only The selection criteria and linkage policy classes follow the definitions specified by [SPPI]. This structure specifies well- defined policy classes and their instances residing in a common, virtual repository [FR-PIB]. The additional PIB-ACCESS clause attribute of "report-only" denotes the usage policy class reported by the PEP. 3.2. Usage32 and Usage64 Textual Conventions The SPPI does not support the Counter32/64 textual conventions (TC) of SNMP - for feedback collection two similar textual conventions have been defined in this PIB: Usage32 and Usage64. In addition to the differential functionality of 'Counter', where only the difference between two samples generally carries information, a single value of a 'Usage' attribute usually provides absolute information, since - its initial value is known (0) - no wrap-around events should occur - the time or event when the initial value was set should be available directly or indirectly from other objects. When 'Usage' attributes are defined in a PRC, events that could cause a reset of the attribute to its initial value should be defined in the description as well as the mechanism that allows the PDP to detect the time of the last reset. No usual COPS activity however should cause the reset of a Usage attribute. In the case of a suspension of monitoring activity (frwkFeedbackActionIndicator set to 'suspendMonitoringAndReports'), 'Usage' attributes should keep their values and continue counting after monitoring is resumed. Rawlins, et al. Informational [Page 8]
RFC 3571 Framework Feedback PIB August 2003 3.3. Feedback Groups and PRCs These policy classes defined in this PIB are common to account type reporting for various technologies and apply to ALL SUBJECT- CATEGORIES. The policy classes are divided into three new groups, namely, The Feedback Report Group, The Feedback Usage Group and The Feedback Selection Group. The policy classes in the Feedback Report Group are: - Feedback Action - Feedback Action List - Feedback Selection Usage Combination Capability - Feedback Linkage - Feedback Traffic Statistics Threshold The policy classes in the Feedback Usage Group are: - Feedback Traffic - Feedback Interface Traffic The policy class in the Feedback Selection Group is: - Feedback RoleCombo Filter Selection 3.3.1. Feedback Action The Feedback Action class contains the attributes that specify action that the PEP is to take regarding policy usage, monitoring and tracking. The PDP may suspend usage monitoring and periodic reporting, suspend periodic reporting only, resume usage and periodic reporting or solicit immediate reporting. The action may affect all feedback policies or be associated with one or more frwkFeedbackLink instances. The frwkFeedbackActionIndicator attribute defines the action. The frwkFeedbackActionPri attribute indicates whether the action applies to all of the usage policies or to a list. The frwkFeedbackActionList attribute is the identifier of the list of Linkage policy instances to which the action is to be applied. The PDP can solicit the PEP for immediate usage feedback. The PEP shall respond with a solicited report containing the usage feedback. The PDP can direct the resumption of usage monitoring and reporting per the defined intervals. For example, the PEP may have re- connected to a PDP and has cached usage policies. The PDP indicates to the PEP to resume usage tracking and monitoring and to send all Rawlins, et al. Informational [Page 9]
RFC 3571 Framework Feedback PIB August 2003 the cached usage policy. The PEP shall respond at the next appropriate interval with an unsolicited report containing the usage feedback. The PDP can suspend the monitoring of usage policy. The PEP maintains the current usage that has been monitored, but discontinues any further monitoring until the PDP directs the PEP to resume monitoring in a subsequent Decision. The PDP can also suspend just the reporting of usage, but not interrupt the monitoring and tracking of usage. The PEP shall discontinue sending Report messages with usage feedback until the PDP directs the PEP to resume. The PEP then begins reporting the usage feedback at the next interval. 3.3.2. Feedback Action List This class defines sets of linkage instances that can be referred to from the frwkFeedbackActionList attribute. 3.3.3. Feedback Linkage Capability This class defines the valid selection criteria PRC, usage PRC and threshold PRC combinations supported by the PEP. 3.3.4. Feedback Linkage This class links the selection criteria instance with the usage class. This table permits the reuse of a selection criteria instance for multiple usage policies. The linkage table also permits the definition of a maximum reporting interval to use when issuing the COPS accounting type reports for the usage instance. A value of 0 in this attribute indicates that the usage policy must be solicited. 3.3.5. Feedback Traffic Statistics Threshold This class is used to provide threshold values for the attributes described in the traffic usage classes below. 3.3.6. Feedback Traffic This class includes the packet counts, byte counts and a reference to the associated Linkage instance. Rawlins, et al. Informational [Page 10]
RFC 3571 Framework Feedback PIB August 2003 3.3.7. Feedback Interface Traffic This class is similar to the previous Feedback Traffic class, except that it includes an additional reference to an interface index. This class should be used with a selection criteria instance that matches an element that is assigned to multiple interfaces. The interface field can be used to associate the instances of this table with the specific element's assignment. 3.3.8. Feedback RoleCombo Filter Selection This class is used as selection criteria based on role combination, capability set and a filter instance. 4. The Feedback Framework PIB Module FRAMEWORK-FEEDBACK-PIB PIB-DEFINITIONS ::= BEGIN IMPORTS pib, Unsigned32, Unsigned64, Integer32, MODULE-IDENTITY, OBJECT-TYPE, MODULE-COMPLIANCE, OBJECT-GROUP FROM COPS-PR-SPPI TruthValue, TEXTUAL-CONVENTION FROM SNMPv2-TC InstanceId, ReferenceId, Prid, TagId, TagReferenceId FROM COPS-PR-SPPI-TC PrcIdentifierOid, PrcIdentifierOidOrZero FROM FRAMEWORK-TC-PIB frwkRoleComboEntry FROM FRAMEWORK-PIB InterfaceIndex FROM IF-MIB; frwkFeedbackPib MODULE-IDENTITY SUBJECT-CATEGORIES { all } LAST-UPDATED "200307140000Z" -- 14 July 2003 ORGANIZATION "IETF RAP WG" CONTACT-INFO "IETF RAP WG Email: rap@ops.ietf.org Diana Rawlins MCI 400 International Parkway Richardson, Texas 75081 Phone: 972-729-4071 Email: Diana.Rawlins@mci.com Rawlins, et al. Informational [Page 11]
RFC 3571 Framework Feedback PIB August 2003 Amol Kulkarni JF3-206 2111 NE 25th Ave Hillsboro, Oregon 97124 Phone: 503-712-1168 Email: amol.kulkarni@intel.com Kwok Ho Chan Nortel Networks 600 Technology Park Drive Billerica, MA 01821 USA Phone: 978-288-8175 Email: khchan@nortelnetworks.com Martin Bokaemper Juniper Networks 700 Silver Seven Road Kanata, ON, K2V 1C3, Canada Phone: 613-591-2735 Email: mbokaemper@juniper.net Dinesh G Dutt Cisco Systems, Inc. 170 Tasman Dr. San Jose, CA 95134-1706 Phone: 408-527-0955 Email: ddutt@cisco.com" DESCRIPTION "The PIB module containing the base set of policy rule classes that are required for support of all policy usage monitoring, tracking and reporting policies. Copyright (C) The Internet Society (2003). This version of this PIB module is part of RFC 3571; see the RFC itself for full legal notices." REVISION "200307140000Z" DESCRIPTION "Initial version, published in RFC 3571." ::= { pib 5 } -- -- Textual Conventions -- Usage32 ::= TEXTUAL-CONVENTION STATUS current Rawlins, et al. Informational [Page 12]
RFC 3571 Framework Feedback PIB August 2003 DESCRIPTION "The Usage32 type represents a non-negative integer which monotonically increases. Usage32 initial value is 0 and the object-type using Usage32 needs to specify when it is initialized. The Usage32 type is intended to reflect the absolute number of counted events, so that even a new PDP after a COPS reconnect can use the value directly. If there is the possibility that the maximum Usage32 value of 2^32-1 is exceeded during the lifetime of the Usage32 object, the larger Usage64 type should be used. If conditions other than the reset of the COPS subsystem exist that disrupt the monotonic characteristics of Usage32, these conditions and a method how to detect their presence should be specified in the description of the object-type using Usage32 or its enclosing object-types (e.g. the Entry or Table object-type of the Usage32 object-type). Whenever the monotonic increase of Usage32 is violated, it should be reset to 0 and the fact that this occurred should be indicated through an appropriate mechanism, for example a corresponding object of type TimeStamp or TimeAndDate." SYNTAX Unsigned32 Usage64 ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "The Usage64 type represents a non-negative integer which monotonically increases. Usage64 initial value is 0 and the object-type using Usage64 needs to specify when it is initialized. The Usage64 type is intended to reflect the absolute number of counted events, so that even a new PDP after a COPS reconnect can use the value directly. The lifetime of the Usage64 object should be defined in a way that ensures the maximum Usage64 value of 2^64-1 is never exceeded. If conditions other than the reset of the COPS Rawlins, et al. Informational [Page 13]
RFC 3571 Framework Feedback PIB August 2003 subsystem exist that disrupt the monotonic characteristics of Usage64, these conditions and a method how to detect their presence should be specified in the description of the object-type using Usage64 or its enclosing object-types (e.g. the Entry or Table object-type of the Usage64 object-type). Whenever the monotonic increase of Usage64 is violated, it should be reset to 0 and the fact that this occurred should be indicated through an appropriate mechanism, for example a corresponding object of type TimeStamp or TimeAndDate." SYNTAX Unsigned64 -- -- The feedback report group -- frwkFeedbackGroupClasses OBJECT IDENTIFIER ::= { frwkFeedbackPib 1 } -- -- Feedback Action Table -- frwkFeedbackActionTable OBJECT-TYPE SYNTAX SEQUENCE OF FrwkFeedbackActionEntry PIB-ACCESS install STATUS current DESCRIPTION "This class represents commands that the PDP sends to suspend, resume or solicit collection or reporting of usage data." ::= { frwkFeedbackGroupClasses 1} frwkFeedbackActionEntry OBJECT-TYPE SYNTAX FrwkFeedbackActionEntry STATUS current DESCRIPTION "Each frwkFeedbackActionEntry represents a command from the PDP. FrwkFeedbackActionIndicator specifies the command itself while frwkFeedbackActionSpecificPri indicates if all frwkFeedbackLink objects in the system are affected by the command, or just the set that is referenced by frwkFeedbackActionList." Rawlins, et al. Informational [Page 14]
RFC 3571 Framework Feedback PIB August 2003 PIB-INDEX { frwkFeedbackActionId} ::= { frwkFeedbackActionTable 1} FrwkFeedbackActionEntry ::= SEQUENCE { frwkFeedbackActionId InstanceId, frwkFeedbackActionIndicator INTEGER, frwkFeedbackActionSpecificPri TruthValue, frwkFeedbackActionList TagReferenceId } frwkFeedbackActionId OBJECT-TYPE SYNTAX InstanceId STATUS current DESCRIPTION "An arbitrary integer index that uniquely identifies an instance of the frwkFeedbackAction class." ::= { frwkFeedbackActionEntry 1} frwkFeedbackActionIndicator OBJECT-TYPE SYNTAX INTEGER { suspendMonitoringAndReports(1), suspendReports(2), resume(3), solicitReport(4) } STATUS current DESCRIPTION "The value indicates if the PEP is to send cached usage policies via COPS accounting type report messages. The enumeration values are: (1) suspendMonitoringAndReports (2) suspendReports (3) resume (4) solicitReport " ::= { frwkFeedbackActionEntry 2 } frwkFeedbackActionSpecificPri OBJECT-TYPE SYNTAX TruthValue STATUS current DESCRIPTION "A value of 0 indicates that the frwkFeedbackActionList attribute should be ignored, and the action applied to all policies. A value of 1 indicates that the action entry has a specific Rawlins, et al. Informational [Page 15]
RFC 3571 Framework Feedback PIB August 2003 list of policies to which it is to be applied." ::= { frwkFeedbackActionEntry 3} frwkFeedbackActionList OBJECT-TYPE SYNTAX TagReferenceId PIB-TAG { frwkFeedbackActionListTag } STATUS current DESCRIPTION "Identifies a group of frwkFeedbackLink instances that this action should affect. The group is identified through a tag reference in the frwkFeedbackList class." ::= { frwkFeedbackActionEntry 4} -- -- Feedback Action List Table -- frwkFeedbackActionListTable OBJECT-TYPE SYNTAX SEQUENCE OF FrwkFeedbackActionListEntry PIB-ACCESS install STATUS current DESCRIPTION "This class defines groups of linkage instances. Groups can be referenced by commands sent by the PDP in a frwkFeedbackActionEntry -in this case the command affects all linkage instances that are part of the group. A group can be referred to by its tag stored in frwkFeedbackActionListTag." ::= { frwkFeedbackGroupClasses 2} frwkFeedbackActionListEntry OBJECT-TYPE SYNTAX FrwkFeedbackActionListEntry STATUS current DESCRIPTION "Each instance associates a linkage instance with a specific ActionListGroup." PIB-INDEX {frwkFeedbackActionListId } UNIQUENESS { frwkFeedbackActionListTag, frwkFeedbackActionListRefID } ::= { frwkFeedbackActionListTable 1} FrwkFeedbackActionListEntry::= SEQUENCE { frwkFeedbackActionListId InstanceId, frwkFeedbackActionListTag TagId, Rawlins, et al. Informational [Page 16]
RFC 3571 Framework Feedback PIB August 2003 frwkFeedbackActionListRefID ReferenceId } frwkFeedbackActionListId OBJECT-TYPE SYNTAX InstanceId STATUS current DESCRIPTION "Arbitrary integer index that uniquely identifies an instance of the class." ::= { frwkFeedbackActionListEntry 1 } frwkFeedbackActionListTag OBJECT-TYPE SYNTAX TagId STATUS current DESCRIPTION "Identifies a group of linkage instances that can be referenced from the Action class." ::= { frwkFeedbackActionListEntry 2 } frwkFeedbackActionListRefID OBJECT-TYPE SYNTAX ReferenceId PIB-REFERENCES { frwkFeedbackLinkEntry } STATUS current DESCRIPTION "A frwkFeedbackLink instance that is referred to by this ReferenceId becomes part of the group, that is identified by the frwkFeedbackActionListTag." ::= { frwkFeedbackActionListEntry 3 } -- -- The Feedback Link Capability Table -- frwkFeedbackLinkCapsTable OBJECT-TYPE SYNTAX SEQUENCE OF FrwkFeedbackLinkCapsEntry PIB-ACCESS notify STATUS current DESCRIPTION "Instances of the frwkFeedbackLink class reference instances of selection and threshold classes and a usage class. This class allows the PEP to communicate valid combinations of these three classes to the PDP." ::= { frwkFeedbackGroupClasses 3} Rawlins, et al. Informational [Page 17]
RFC 3571 Framework Feedback PIB August 2003 frwkFeedbackLinkCapsEntry OBJECT-TYPE SYNTAX FrwkFeedbackLinkCapsEntry STATUS current DESCRIPTION "The attributes of this class identify valid combinations of selection criteria, usage and threshold classes for feedback." PIB-INDEX { frwkFeedbackLinkCapsId } UNIQUENESS { frwkFeedbackLinkCapsSelection, frwkFeedbackLinkCapsUsage, frwkFeedbackLinkCapsThreshold } ::= {frwkFeedbackLinkCapsTable 1} FrwkFeedbackLinkCapsEntry ::= SEQUENCE { frwkFeedbackLinkCapsId InstanceId, frwkFeedbackLinkCapsSelection PrcIdentifierOid, frwkFeedbackLinkCapsUsage PrcIdentifierOid, frwkFeedbackLinkCapsThreshold PrcIdentifierOidOrZero } frwkFeedbackLinkCapsId OBJECT-TYPE SYNTAX InstanceId STATUS current DESCRIPTION "An arbitrary integer index that uniquely identifies an instance of the frwkFeedbackLinkCaps class." ::= { frwkFeedbackLinkCapsEntry 1} frwkFeedbackLinkCapsSelection OBJECT-TYPE SYNTAX PrcIdentifierOid STATUS current DESCRIPTION "The identifier of a class that is supported by the device for feedback selection in combination with the usage and threshold classes referenced in this instance." ::= { frwkFeedbackLinkCapsEntry 2} frwkFeedbackLinkCapsUsage OBJECT-TYPE SYNTAX PrcIdentifierOid STATUS current DESCRIPTION "The identifier of the usage class that is supported by the PEP in combination with the selection and threshold classes referenced in this instance." Rawlins, et al. Informational [Page 18]
RFC 3571 Framework Feedback PIB August 2003 ::= { frwkFeedbackLinkCapsEntry 3} frwkFeedbackLinkCapsThreshold OBJECT-TYPE SYNTAX PrcIdentifierOidOrZero STATUS current DESCRIPTION "The identifier of the threshold class that is supported by the PEP in combination with the selection and usage classes referenced in this instance. 0.0 is used if this combination does not allow a threshold." ::= { frwkFeedbackLinkCapsEntry 4} -- -- The Feedback Report Linkage Table -- frwkFeedbackLinkTable OBJECT-TYPE SYNTAX SEQUENCE OF FrwkFeedbackLinkEntry PIB-ACCESS install STATUS current DESCRIPTION "This class associates the selection criteria with the usage policy. It also permits the defining of the max interval used for reporting the usage instance." ::= { frwkFeedbackGroupClasses 4} frwkFeedbackLinkEntry OBJECT-TYPE SYNTAX FrwkFeedbackLinkEntry STATUS current DESCRIPTION "This class associates the selection criteria with the usage policy. It also permits the defining of the max interval used for reporting the usage instance." PIB-INDEX { frwkFeedbackLinkId } UNIQUENESS {frwkFeedbackLinkSel, frwkFeedbackLinkUsage } ::= {frwkFeedbackLinkTable 1} FrwkFeedbackLinkEntry ::= SEQUENCE { frwkFeedbackLinkId InstanceId, frwkFeedbackLinkSel Prid, frwkFeedbackLinkUsage PrcIdentifierOid, frwkFeedbackLinkInterval Integer32, frwkFeedbackLinkThreshold Prid, frwkFeedbackLinkFlags BITS Rawlins, et al. Informational [Page 19]
RFC 3571 Framework Feedback PIB August 2003 } frwkFeedbackLinkId OBJECT-TYPE SYNTAX InstanceId STATUS current DESCRIPTION "An arbitrary integer index that uniquely identifies an instance of the frwkFeedbackLinkTable class." ::= { frwkFeedbackLinkEntry 1} frwkFeedbackLinkSel OBJECT-TYPE SYNTAX Prid STATUS current DESCRIPTION "The PRID of the Policy Class instance as the monitoring point, or the PRID of the selection criteria instance that defines the conditions for monitoring, to be use by the PEP for usage reporting." ::= { frwkFeedbackLinkEntry 2} frwkFeedbackLinkUsage OBJECT-TYPE SYNTAX PrcIdentifierOid STATUS current DESCRIPTION "The identifier of the usage class that the PEP uses to monitor, record and report." ::= { frwkFeedbackLinkEntry 3} frwkFeedbackLinkInterval OBJECT-TYPE SYNTAX Integer32 STATUS current DESCRIPTION "Maximum interval in units of the value of the Accounting Timer specified by the PDP in the client accept message. A frwkFeedbackLinkInterval of 1 is equal to the value of the Accounting Timer. This value must be 1 or greater. " ::= { frwkFeedbackLinkEntry 4} frwkFeedbackLinkThreshold OBJECT-TYPE SYNTAX Prid STATUS current DESCRIPTION "The PRID of a threshold class instance. This instance specifies the threshold values for the usage policy." Rawlins, et al. Informational [Page 20]
RFC 3571 Framework Feedback PIB August 2003 ::= { frwkFeedbackLinkEntry 5} frwkFeedbackLinkFlags OBJECT-TYPE SYNTAX BITS { periodic(0), threshold(1), changeOnly(2) } STATUS current DESCRIPTION "This value indicates the reporting basis of the usage policy. The feed back may be generated on demand, on a periodic basis regardless of a change in value from the previous report, on a periodic basis if a change in value has occurred, or the usage is reported when an identified threshold value in the usage instance has been reached. If the 'periodic' flag is set, the PEP will provide unsolicited reports at the rate specified in frwkFeedbackLinkInterval. If the 'periodic' flag is not set, reports will only be generated when solicited by the PDP. The 'threshold' and 'changeOnly' flags make the periodic reports conditional - these flags only make sense in combination with the 'periodic' flag." ::= { frwkFeedbackLinkEntry 6} -- -- The Threshold class that accompanies the above Usage PRCs -- frwkFeedbackTrafficThresTable OBJECT-TYPE SYNTAX SEQUENCE OF FrwkFeedbackTrafficThresEntry PIB-ACCESS install STATUS current DESCRIPTION "This class defines the threshold attributes corresponding to usage attributes specified in frwkFeedbackTrafficTable, frwkFeedbackIfTrafficTable and other similar usage classes. The usage object is considered to match the threshold condition if at least one of the packet or byte threshold conditions match. The byte and packet thresholds are considered to match, if the threshold is present (not ASN1 NULL) Rawlins, et al. Informational [Page 21]
RFC 3571 Framework Feedback PIB August 2003 and the corresponding usage value exceeds the threshold." ::= { frwkFeedbackGroupClasses 5} frwkFeedbackTrafficThresEntry OBJECT-TYPE SYNTAX FrwkFeedbackTrafficThresEntry STATUS current DESCRIPTION "Defines the attributes to hold threshold values." PIB-INDEX {frwkFeedbackTrafficThresId} ::= {frwkFeedbackTrafficThresTable 1} FrwkFeedbackTrafficThresEntry ::= SEQUENCE { frwkFeedbackTrafficThresId InstanceId, frwkFeedbackTrafficThresPackets Unsigned64, frwkFeedbackTrafficThresBytes Unsigned64 } frwkFeedbackTrafficThresId OBJECT-TYPE SYNTAX InstanceId STATUS current DESCRIPTION "Arbitrary integer index that uniquely identifies an instance of the class." ::= { frwkFeedbackTrafficThresEntry 1 } frwkFeedbackTrafficThresPackets OBJECT-TYPE SYNTAX Unsigned64 STATUS current DESCRIPTION "The threshold, in terms of packets, that must be matched or exceeded to trigger a report in the next reporting interval." ::= { frwkFeedbackTrafficThresEntry 2 } frwkFeedbackTrafficThresBytes OBJECT-TYPE SYNTAX Unsigned64 STATUS current DESCRIPTION "The threshold, in terms of bytes, that must be exceeded to trigger a report in the next reporting interval." ::= { frwkFeedbackTrafficThresEntry 3 } -- Rawlins, et al. Informational [Page 22]
RFC 3571 Framework Feedback PIB August 2003 -- All actual usage classes are in the separate -- frwkFeedbackUsageClasses group -- frwkFeedbackUsageClasses OBJECT IDENTIFIER ::= { frwkFeedbackPib 2 } -- -- The generic traffic (byte & packet count) usage class -- frwkFeedbackTrafficTable OBJECT-TYPE SYNTAX SEQUENCE OF FrwkFeedbackTrafficEntry PIB-ACCESS report-only STATUS current DESCRIPTION "This class defines the usage attributes that the PEP is to monitor for plain traffic handling elements like filters. All packets and the bytes contained in these packets are counted. It also contains the PRID of the linkage instance associating the selection criteria instance with the usage instance." ::= { frwkFeedbackUsageClasses 1} frwkFeedbackTrafficEntry OBJECT-TYPE SYNTAX FrwkFeedbackTrafficEntry STATUS current DESCRIPTION "Defines the attributes the PEP is to monitor, record and report." PIB-INDEX {frwkFeedbackTrafficId} UNIQUENESS { frwkFeedbackTrafficLinkRefID } ::= {frwkFeedbackTrafficTable 1} FrwkFeedbackTrafficEntry ::= SEQUENCE { frwkFeedbackTrafficId InstanceId, frwkFeedbackTrafficLinkRefID ReferenceId, frwkFeedbackTrafficPacketCount Usage64, frwkFeedbackTrafficByteCount Usage64 } frwkFeedbackTrafficId OBJECT-TYPE SYNTAX InstanceId STATUS current Rawlins, et al. Informational [Page 23]
RFC 3571 Framework Feedback PIB August 2003 DESCRIPTION "Arbitrary integer index that uniquely identifies an instance of the class." ::= { frwkFeedbackTrafficEntry 1 } frwkFeedbackTrafficLinkRefID OBJECT-TYPE SYNTAX ReferenceId PIB-REFERENCES { frwkFeedbackLinkEntry } STATUS current DESCRIPTION "The ReferenceId of the Linkage policy instance used to base this usage policy instance upon." ::= { frwkFeedbackTrafficEntry 2 } frwkFeedbackTrafficPacketCount OBJECT-TYPE SYNTAX Usage64 STATUS current DESCRIPTION "The count of packets handled by the associated element. The initial value of 0 is set when the frwkFeedbackTraffic instance is created, for example triggered through the creation of a frwkFeedbackLink instance." ::= {frwkFeedbackTrafficEntry 3} frwkFeedbackTrafficByteCount OBJECT-TYPE SYNTAX Usage64 STATUS current DESCRIPTION "The byte count of packets handled by the associated element. The initial value of 0 is set when the frwkFeedbackTraffic instance is created." ::= { frwkFeedbackTrafficEntry 4} -- -- The traffic usage class, qualified for an interface -- frwkFeedbackIfTrafficTable OBJECT-TYPE SYNTAX SEQUENCE OF FrwkFeedbackIfTrafficEntry PIB-ACCESS report-only STATUS current DESCRIPTION "A usage class similar to the basic Traffic class that also contains a reference to an interface index. This Rawlins, et al. Informational [Page 24]
RFC 3571 Framework Feedback PIB August 2003 class should be used with an underspecified selection criteria entry from the frwkRoleComboTable that matches an element that can be assigned to multiple interface indices. The interface field can be used to associate the instances of this class with the specific element's assignment." ::= { frwkFeedbackUsageClasses 2 } frwkFeedbackIfTrafficEntry OBJECT-TYPE SYNTAX FrwkFeedbackIfTrafficEntry STATUS current DESCRIPTION "Defines the attributes the PEP is to monitor, record and report." PIB-INDEX {frwkFeedbackIfTrafficId} UNIQUENESS { frwkFeedbackIfTrafficLinkRefID, frwkFeedbackIfTrafficIfIndex } ::= {frwkFeedbackIfTrafficTable 1} FrwkFeedbackIfTrafficEntry ::= SEQUENCE { frwkFeedbackIfTrafficId InstanceId, frwkFeedbackIfTrafficLinkRefID ReferenceId, frwkFeedbackIfTrafficIfIndex InterfaceIndex, frwkFeedbackIfTrafficPacketCount Usage64, frwkFeedbackIfTrafficByteCount Usage64 } frwkFeedbackIfTrafficId OBJECT-TYPE SYNTAX InstanceId STATUS current DESCRIPTION "Arbitrary integer index that uniquely identifies an instance of the class." ::= { frwkFeedbackIfTrafficEntry 1 } frwkFeedbackIfTrafficLinkRefID OBJECT-TYPE SYNTAX ReferenceId PIB-REFERENCES { frwkFeedbackLinkEntry } STATUS current DESCRIPTION "The ReferenceId of the Linkage policy instance used to base this usage policy instance upon." ::= { frwkFeedbackIfTrafficEntry 2 } frwkFeedbackIfTrafficIfIndex OBJECT-TYPE SYNTAX InterfaceIndex Rawlins, et al. Informational [Page 25]
RFC 3571 Framework Feedback PIB August 2003 STATUS current DESCRIPTION "The value of this attribute is the ifIndex which is associated with the specified RoleCombination and interface capability set name." ::= { frwkFeedbackIfTrafficEntry 3 } frwkFeedbackIfTrafficPacketCount OBJECT-TYPE SYNTAX Usage64 STATUS current DESCRIPTION "The count of packets handled by the associated element. The initial value of 0 is set when the frwkFeedbackIfTraffic instance is created." ::= { frwkFeedbackIfTrafficEntry 4 } frwkFeedbackIfTrafficByteCount OBJECT-TYPE SYNTAX Usage64 STATUS current DESCRIPTION "The byte count of packets handled by the associated element. The initial value of 0 is set when the frwkFeedbackIfTraffic instance is created." ::= { frwkFeedbackIfTrafficEntry 5 } -- -- All Selection classes are in the separate -- FrwkFeedbackSelectionClasses group -- frwkFeedbackSelectionClasses OBJECT IDENTIFIER ::= { frwkFeedbackPib 3 } -- -- The Role Combination Filter Selection Table -- frwkFeedbackRoleFilterSelTable OBJECT-TYPE SYNTAX SEQUENCE OF FrwkFeedbackRoleFilterSelEntry PIB-ACCESS install STATUS current DESCRIPTION "A selection class that defines selection of objects for monitoring based on the role combination, capability set and a filter." ::= { frwkFeedbackSelectionClasses 1 } Rawlins, et al. Informational [Page 26]
RFC 3571 Framework Feedback PIB August 2003 frwkFeedbackRoleFilterSelEntry OBJECT-TYPE SYNTAX FrwkFeedbackRoleFilterSelEntry STATUS current DESCRIPTION "Each instance selects a filter on multiple interfaces that share the same frwkRoleCombo instance." PIB-INDEX { frwkFeedbackRoleFilterSelId} UNIQUENESS { frwkFeedbackRoleFilterSelRCombo, frwkFeedbackRoleFilterSelFilter } ::= {frwkFeedbackRoleFilterSelTable 1} FrwkFeedbackRoleFilterSelEntry ::= SEQUENCE { frwkFeedbackRoleFilterSelId InstanceId, frwkFeedbackRoleFilterSelRCombo ReferenceId, frwkFeedbackRoleFilterSelFilter Prid } frwkFeedbackRoleFilterSelId OBJECT-TYPE SYNTAX InstanceId STATUS current DESCRIPTION "Arbitrary integer index that uniquely identifies an instance of the class." ::= { frwkFeedbackRoleFilterSelEntry 1 } frwkFeedbackRoleFilterSelRCombo OBJECT-TYPE SYNTAX ReferenceId PIB-REFERENCES { frwkRoleComboEntry } STATUS current DESCRIPTION "The ReferenceId of the frwkRoleComboTable policy instance used for selection." ::= { frwkFeedbackRoleFilterSelEntry 2 } frwkFeedbackRoleFilterSelFilter OBJECT-TYPE SYNTAX Prid STATUS current DESCRIPTION "The identifier of a filter instance. Valid classes are the subclasses of frwkBaseFilter: - frwkIpFilter - frwk802Filter - frwkILabelFilter" ::= { frwkFeedbackRoleFilterSelEntry 3 } Rawlins, et al. Informational [Page 27]
RFC 3571 Framework Feedback PIB August 2003 -- -- Compliance Section -- frwkFeedbackPibConformance OBJECT IDENTIFIER ::= { frwkFeedbackPib 4 } frwkFeedbackPibCompliances OBJECT IDENTIFIER ::= { frwkFeedbackPibConformance 1 } frwkFeedbackPibGroups OBJECT IDENTIFIER ::= { frwkFeedbackPibConformance 2 } frwkFeedbackPibCompliance MODULE-COMPLIANCE STATUS current DESCRIPTION "Describes the requirements for conformance to the feedback framework PIB" MODULE -- this module MANDATORY-GROUPS { frwkFeedbackLinkCapsGroup, frwkFeedbackLinkGroup, frwkFeedbackActionGroup } GROUP frwkFeedbackActionListGroup DESCRIPTION "The frwkFeedbackActionListGroup is mandatory if actions on subsets linkEntries are to be supported." GROUP frwkFeedbackTrafficGroup DESCRIPTION "The frwkFeedbackTrafficGroup is mandatory if monitoring of traffic data is to be supported." GROUP frwkFeedbackTrafficThresGroup DESCRIPTION "The frwkFeedbackTrafficThresGroup is mandatory if conditional reporting of traffic usage thresholds is to be supported." GROUP frwkFeedbackIfTrafficGroup DESCRIPTION "The frwkFeedbackIfTrafficGroup is mandatory if per-interface usage collection of traffic data is to be supported." Rawlins, et al. Informational [Page 28]
RFC 3571 Framework Feedback PIB August 2003 GROUP frwkFeedbackRoleFilterSelGroup DESCRIPTION "The frwkFeedbackRoleFilterSelGroup is mandatory if monitoring of filters referenced through the frwkRoleCombo class is to be supported." ::= { frwkFeedbackPibCompliances 1 } frwkFeedbackLinkCapsGroup OBJECT-GROUP OBJECTS { frwkFeedbackLinkCapsId, frwkFeedbackLinkCapsSelection, frwkFeedbackLinkCapsUsage, frwkFeedbackLinkCapsThreshold } STATUS current DESCRIPTION "Objects from the frwkFeedbackLinkCapsTable." ::= { frwkFeedbackPibGroups 1 } frwkFeedbackLinkGroup OBJECT-GROUP OBJECTS { frwkFeedbackLinkId, frwkFeedbackLinkSel, frwkFeedbackLinkUsage, frwkFeedbackLinkInterval, frwkFeedbackLinkThreshold, frwkFeedbackLinkFlags } STATUS current DESCRIPTION "Objects from the frwkFeedbackLinkTable." ::= { frwkFeedbackPibGroups 2 } frwkFeedbackActionGroup OBJECT-GROUP OBJECTS { frwkFeedbackActionId, frwkFeedbackActionIndicator, frwkFeedbackActionSpecificPri, frwkFeedbackActionList } STATUS current DESCRIPTION "Objects from the frwkFeedbackActionTable." ::= { frwkFeedbackPibGroups 3 } frwkFeedbackActionListGroup OBJECT-GROUP OBJECTS { Rawlins, et al. Informational [Page 29]
RFC 3571 Framework Feedback PIB August 2003 frwkFeedbackActionListId, frwkFeedbackActionListTag, frwkFeedbackActionListRefID } STATUS current DESCRIPTION "Objects from the frwkFeedbackActionListTable." ::= { frwkFeedbackPibGroups 4 } frwkFeedbackTrafficGroup OBJECT-GROUP OBJECTS { frwkFeedbackTrafficId, frwkFeedbackTrafficLinkRefID, frwkFeedbackTrafficPacketCount, frwkFeedbackTrafficByteCount } STATUS current DESCRIPTION "Objects from the frwkFeedbackTrafficTable." ::= { frwkFeedbackPibGroups 5 } frwkFeedbackTrafficThresGroup OBJECT-GROUP OBJECTS { frwkFeedbackTrafficThresId, frwkFeedbackTrafficThresPackets, frwkFeedbackTrafficThresBytes } STATUS current DESCRIPTION "Objects from the frwkFeedbackTrafficThresTable." ::= { frwkFeedbackPibGroups 6 } frwkFeedbackIfTrafficGroup OBJECT-GROUP OBJECTS { frwkFeedbackIfTrafficId, frwkFeedbackIfTrafficLinkRefID, frwkFeedbackIfTrafficIfIndex, frwkFeedbackIfTrafficPacketCount, frwkFeedbackIfTrafficByteCount } STATUS current DESCRIPTION "Objects from the frwkFeedbackIfTrafficTable." ::= { frwkFeedbackPibGroups 7 } frwkFeedbackRoleFilterSelGroup OBJECT-GROUP OBJECTS { frwkFeedbackRoleFilterSelId, Rawlins, et al. Informational [Page 30]
RFC 3571 Framework Feedback PIB August 2003 frwkFeedbackRoleFilterSelRCombo, frwkFeedbackRoleFilterSelFilter } STATUS current DESCRIPTION "Objects from the frwkFeedbackRoleFilterSelTable." ::= { frwkFeedbackPibGroups 8 } END 5. Security Considerations This PIB defines structured information that may be sensitive when transported by the COPS protocol [COPS-PR]. This PIB does not contain classes that directly contain security relevant information like passwords or monetary amounts. However, unauthorized access or changes to information defined in this PIB could compromise network operations or reveal sensitive business or personal information. Specifically for the classes: frwkFeedbackLinkCaps This class has the ACCESS clause 'notify'. Access to this information reveals feedback collection capabilities of the COPS client and malicious changes could affect feedback operation by misleading the server to generate corrupt feedback configuration. frwkFeedbackLinkTable, frwkFeedbackAction, frwkFeedbackActionList, frwkFeedbackTrafficThres, frwkFeedbackRoleFilterSel These classes have the ACCESS clause 'install' and allow the COPS server to control feedback collection and reporting on the client. Access to this information exposes the client's configuration; malicious changes could disrupt network or business operations and raise privacy issues. frwkFeedbackTraffic, frwkFeedbackIfTraffic These classes have the ACCESS clause 'report-only' and contain the usage information delivered from the COPS client to the server. Unauthorized access to this information may reveal detailed information on the network and its users. Malicious changes may affect network and business operations. Rawlins, et al. Informational [Page 31]
RFC 3571 Framework Feedback PIB August 2003 [COPS] and [COPS-PR] define mechanisms to secure the COPS protocol communication and implementations of COPS servers or clients supporting this PIB MUST follow the security guidelines specified there. 6. IANA Considerations This document describes the frwkFeedbackPib Policy Information Base (PIB) module for registration under the "pib" branch registered with IANA. The IANA has assigned PIB number 5. This PIB uses "all" in the SUBJECT-CATEGORY clause, so it applies to all COPS client types. No new COPS client type is requested for this PIB. 7. Acknowledgements The authors would like to thank Dave Durham, Ravi Sahita, and Russell Fenger of Intel and John K. Gallant of WorldCom for their contribution to this document. 8. References 8.1. Normative References [COPS] Durham, D., Boyle, J., Cohen, R., Herzog, S., Rajan, R. and A. Sastry, "The COPS (Common Open Policy Service) Protocol", RFC 2748, January 2000. [COPS-PR] Chan, K., Seligson, J., Durham, D., Gai, S., McCloghrie, K., Herzog, S., Reichmeyer, F., Yavatkar, R. and A. Smith, "COPS Usage for Policy Provisioning", RFC 3084, May 2001. [IFMIB] McCloghrie, K. and F. Kastenholz, "The Interfaces Group MIB", RFC 2863, June 2000. [FR-PIB] Sahita, R., Hahn, S., Chan, K. and K. McCloghrie, "Framework Policy Information Base", RFC 3318, March 2003. [FEEDBACKFWK] Rawlins, D., Kulkarni, A., Bokaemper, M. and K. Chan, "Framework for Policy Usage Feedback for Common Open Policy Service with Policy Provisioning (COPS-PR)", RFC 3483, March 2003. Rawlins, et al. Informational [Page 32]
RFC 3571 Framework Feedback PIB August 2003 [RFC2119] Bradner, S., "Key words for use in RFCs to Indicate Requirement Levels", BCP 14, RFC 2119, March 1997. [RFC2578] McCloghrie, K., Perkins, D., Schoenwaelder, J., Case, J., Rose, M. and S. Waldbusser, "Structure of Management Information Version 2 (SMIv2)", STD 58, RFC 2578, April 1999. [RFC2579] McCloghrie, K., Perkins, D., Schoenwaelder, J., Case, J., Rose, M. and S. Waldbusser, "Textual Conventions for SMIv2", STD 58, RFC 2579, April 1999. 8.2. Informational References [COPS-TLS], Walker, J., Kulkarni, A.,"COPS Over TLS", Work in Progress. [DIFFSERV-PIB] Chan, K., Sahita, R., Hahn, S. and K. McCloghrie, "Differentiated Services Quality of Service Policy Information Base", RFC 3317, March 2003. Rawlins, et al. Informational [Page 33]
RFC 3571 Framework Feedback PIB August 2003 9. Authors' Addresses Diana Rawlins MCI 400 International Parkway Richardson, Texas 75081 Phone: 972-729-4071 EMail: Diana.Rawlins@mci.com Amol Kulkarni JF3-206 2111 NE 25th Ave Hillsboro, Oregon 97124 Phone: 503-712-1168 EMail: amol.kulkarni@intel.com Kwok Ho Chan Nortel Networks 600 Technology Park Drive Billerica, MA 01821 USA Phone: 978-288-8175 EMail: khchan@nortelnetworks.com Martin Bokaemper Juniper Networks 700 Silver Seven Road Kanata, ON, K2V 1C3, Canada Phone: 613-591-2735 EMail: mbokaemper@juniper.net Dinesh G Dutt Cisco Systems, Inc. 170 Tasman Dr. San Jose, CA 95134-1706 Phone: 408-527-0955 EMail: ddutt@cisco.com Rawlins, et al. Informational [Page 34]
RFC 3571 Framework Feedback PIB August 2003 10. Full Copyright Statement Copyright (C) The Internet Society (2003). All Rights Reserved. This document and translations of it may be copied and furnished to others, and derivative works that comment on or otherwise explain it or assist in its implementation may be prepared, copied, published and distributed, in whole or in part, without restriction of any kind, provided that the above copyright notice and this paragraph are included on all such copies and derivative works. However, this document itself may not be modified in any way, such as by removing the copyright notice or references to the Internet Society or other Internet organizations, except as needed for the purpose of developing Internet standards in which case the procedures for copyrights defined in the Internet Standards process must be followed, or as required to translate it into languages other than English. The limited permissions granted above are perpetual and will not be revoked by the Internet Society or its successors or assignees. This document and the information contained herein is provided on an "AS IS" basis and THE INTERNET SOCIETY AND THE INTERNET ENGINEERING TASK FORCE DISCLAIMS ALL WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO ANY WARRANTY THAT THE USE OF THE INFORMATION HEREIN WILL NOT INFRINGE ANY RIGHTS OR ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. Acknowledgement Funding for the RFC Editor function is currently provided by the Internet Society. Rawlins, et al. Informational [Page 35]
mirror server hosted at Truenetwork, Russian Federation.