Internet Engineering Task Force (IETF)                       J. Mattsson
Request for Comments: 6043                                      Ericsson
Category: Informational                                          T. Tian
ISSN: 2070-1721                                                      ZTE
                                                              March 2011


          MIKEY-TICKET: Ticket-Based Modes of Key Distribution
                 in Multimedia Internet KEYing (MIKEY)

Abstract

   The Multimedia Internet KEYing (MIKEY) specification describes a key
   management scheme for real-time applications.  In this document, we
   note that the currently defined MIKEY modes are insufficient to
   address deployment scenarios built around a centralized key
   management service.  Interest in such deployments is increasing.
   Therefore, a set of new MIKEY modes that work well in such scenarios
   are defined.  The new modes use a trusted key management service and
   a ticket concept, similar to that in Kerberos.  The new modes also
   support features used by many existing applications, where the exact
   identity of the other endpoint may not be known at the start of the
   communication session.

Status of This Memo

   This document is not an Internet Standards Track specification; it is
   published for informational purposes.

   This document is a product of the Internet Engineering Task Force
   (IETF).  It represents the consensus of the IETF community.  It has
   received public review and has been approved for publication by the
   Internet Engineering Steering Group (IESG).  Not all documents
   approved by the IESG are a candidate for any level of Internet
   Standard; see Section 2 of RFC 5741.

   Information about the current status of this document, any errata,
   and how to provide feedback on it may be obtained at
   http://www.rfc-editor.org/info/rfc6043.












Mattsson & Tian               Informational                     [Page 1]


RFC 6043                      MIKEY-TICKET                    March 2011


Copyright Notice

   Copyright (c) 2011 IETF Trust and the persons identified as the
   document authors.  All rights reserved.

   This document is subject to BCP 78 and the IETF Trust's Legal
   Provisions Relating to IETF Documents
   (http://trustee.ietf.org/license-info) in effect on the date of
   publication of this document.  Please review these documents
   carefully, as they describe your rights and restrictions with respect
   to this document.  Code Components extracted from this document must
   include Simplified BSD License text as described in Section 4.e of
   the Trust Legal Provisions and are provided without warranty as
   described in the Simplified BSD License.

Table of Contents

   1. Introduction ....................................................4
   2. Terminology .....................................................4
      2.1. Definitions and Notation ...................................5
      2.2. Abbreviations ..............................................6
      2.3. Payloads ...................................................6
   3. Design Considerations ...........................................7
   4. MIKEY-TICKET ....................................................9
      4.1. Overview ...................................................9
           4.1.1. Modes ..............................................12
      4.2. Exchanges .................................................13
           4.2.1. Ticket Request .....................................13
           4.2.2. Ticket Transfer ....................................16
           4.2.3. Ticket Resolve .....................................19
   5. Key Management Functions .......................................23
      5.1. Key Derivation ............................................23
           5.1.1. Deriving Forked Keys ...............................25
           5.1.2. Deriving Keys from an Envelope Key/PSK/MPK .........26
           5.1.3. Deriving Keys from a TGK/GTGK ......................27
      5.2. CSB Updating ..............................................28
      5.3. Ticket Reuse ..............................................29
      5.4. Error Handling ............................................29
      5.5. MAC/Signature Coverage ....................................30
   6. Payload Encoding ...............................................31
      6.1. Common Header Payload (HDR) ...............................31
           6.1.1. The GENERIC-ID Map Type ............................33
      6.2. Key Data Transport Payload (KEMAC) ........................34
           6.2.1. Key Data Sub-Payload ...............................35
      6.3. Timestamp Payload (T) .....................................36
      6.4. Timestamp Payload with Role Indicator (TR) ................36
      6.5. ID Payload (ID) ...........................................37
      6.6. ID Payload with Role Indicator (IDR) ......................37



Mattsson & Tian               Informational                     [Page 2]


RFC 6043                      MIKEY-TICKET                    March 2011


      6.7. Cert Hash Payload (CHASH) .................................38
      6.8. RAND Payload with Role Indicator (RANDR) ..................38
      6.9. Error Payload (ERR) .......................................39
      6.10. Ticket Policy Payload (TP) / Ticket Payload (TICKET) .....39
   7. Transport Protocols ............................................43
   8. Pre-Encrypted Content ..........................................43
   9. Group Communication ............................................44
      9.1. Key Forking ...............................................45
   10. Signaling between Different KMSs ..............................45
   11. Adding New Ticket Types to MIKEY-TICKET .......................46
   12. Security Considerations .......................................47
      12.1. General ..................................................47
      12.2. Key Forking ..............................................48
      12.3. Denial of Service ........................................49
      12.4. Replay ...................................................49
      12.5. Group Key Management .....................................50
   13. Acknowledgements ..............................................50
   14. IANA Considerations ...........................................50
   15. References ....................................................53
      15.1. Normative References .....................................53
      15.2. Informative References ...................................53
   Appendix A.  MIKEY Base Ticket ....................................55
     A.1.  Components of the Ticket Data .............................55
     A.2.  Key Derivation ............................................56
       A.2.1.  Deriving Keys from a TPK ..............................56
       A.2.2.  Deriving MPKi and MPKr ................................57
     A.3.  Ticket Header Payload (THDR) ..............................57
   Appendix B.  Alternative Use Cases ................................58
     B.1.  Compatibility Mode ........................................58






















Mattsson & Tian               Informational                     [Page 3]


RFC 6043                      MIKEY-TICKET                    March 2011


1.  Introduction

   Key management systems are either based on negotiation and exchange
   directly between peers (e.g., Diffie-Hellman-based schemes), pre-
   distribution of user credentials (shared secrets/certificates), or
   availability of a trusted Key Management Service (KMS).  The modes
   described in the Multimedia Internet KEYing (MIKEY) specification
   [RFC3830] and its extensions [RFC4650] [RFC4738] are all variants of
   the first two alternatives.

   In security systems serving a large number of users, a solution based
   on a key management service is often preferred.  With such a service
   in place, there is no need to pre-distribute credentials that
   directly can be used to establish security associations between peers
   for protected communication, as users can request such credentials
   when needed.  Solutions based on a trusted key management service
   also scale well when the number of users grows.

   This document introduces a set of new MIKEY modes that go under the
   common name MIKEY-TICKET.  The new modes support a ticket concept,
   similar to that in Kerberos [RFC4120], which is used to identify and
   deliver keys.  A high-level outline of MIKEY-TICKET as defined herein
   is that the Initiator requests keys and a ticket from the KMS and
   sends the ticket to the Responder.  The ticket contains a reference
   to the keys, or the enveloped keys.  The Responder then sends the
   ticket to the KMS, which returns the appropriate keys.

   MIKEY-TICKET is primarily designed to be used for media plane
   security in the 3rd Generation Partnership Project (3GPP) IP
   Multimedia Subsystem (IMS) [3GPP.33.328].  This implies that some
   extensions to the basic Kerberos concept are needed.  For instance,
   the Initiator may not always know the exact identity of the Responder
   when the communication with the key management server is initiated.

   This document defines a signaling framework enabling peers to
   request, transfer, and resolve various Ticket Types using a key
   management service.  A default Ticket Type is also defined.  To allow
   the use of 256-bit keys for users with high security requirements,
   additional encryption, authentication, and pseudorandom functions are
   defined.  And to eliminate the limitations with the existing SRTP-ID
   map type, a new CS ID map type called GENERIC-ID is defined.

2.  Terminology

   The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
   "SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this
   document are to be interpreted as described in [RFC2119].




Mattsson & Tian               Informational                     [Page 4]


RFC 6043                      MIKEY-TICKET                    March 2011


   Definitions of terms and notation will, unless otherwise stated, be
   as defined in [RFC3830].

2.1.  Definitions and Notation

   Forking: The delivery of a request to multiple endpoints (multiple
   devices owned by a single user or multiple users).

   Key forking: When used in conjunction with forking, key forking
   refers to the process of modifying keys, making them
   cryptographically unique for each responder targeted by the forking.

   (Media) session: The communication session intended to be secured by
   the MIKEY-TICKET provided key(s).

   Session information: Information related to the security protocols
   used to protect the media session: keys, salts, algorithms, etc.

   Ticket: A Kerberos-like object used to identify and deliver keys over
   an untrusted network.

   Ticket Data: Ticket part with information intended only for the party
   that resolves the ticket (e.g., keys).

   Ticket Request: Exchange used by the Initiator to request keys and a
   ticket from a trusted KMS.

   Ticket Transfer: Exchange used to transfer the ticket as well as
   session information from the Initiator to the Responder.

   Ticket Resolve: Exchange used by the Responder to request the KMS to
   return the keys encoded in a ticket.

   Ticket Policy: Policy for ticket generation and resolution,
   authorized applications, key derivation, etc.

   Ticket Type: Defines ticket format and processing.  May further have
   subtype and version.

   Solid arrows  (----->) indicate mandatory messages.
   Dashed arrows (- - ->) indicate optional messages.

   E(k, p)   Encryption of p with the key k
   PKx       Public Key of entity x
   k'        The forked key k
   [p]       p is optional
   {p}       Zero or more occurrences of p
   (p)       One or more occurrences of p



Mattsson & Tian               Informational                     [Page 5]


RFC 6043                      MIKEY-TICKET                    March 2011


   ||        Concatenation
   |         OR (selection operator)

2.2.  Abbreviations

   3GPP:     3rd Generation Partnership Project
   AAA:      Authentication, Authorization, and Accounting
   ACL:      Access Control List
   AES:      Advanced Encryption Standard
   CA:       Certification Authority
   CS:       Crypto Session
   CSB:      Crypto Session Bundle
   IMS:      IP Multimedia Subsystem
   GTGK:     Group TGK
   HMAC:     Hash-based Message Authentication Code
   KMS:      Key Management Service
   MAC:      Message Authentication Code
   MIKEY:    Multimedia Internet KEYing
   NSPS:     National Security and Public Safety
   MKI:      Master Key Identifier
   MPK:      MIKEY Protection Key
   NTP:      Network Time Protocol
   PET:      Privacy Enhancing Technologies
   PK:       Public Key
   PRF:      Pseudorandom Function
   PRNG:     Pseudorandom Number Generator
   PSK:      Pre-Shared Key
   RTSP:     Real Time Streaming Protocol
   SDP:      Session Description Protocol
   SHA:      Secure Hash Algorithm
   SIP:      Session Initiation Protocol
   SPI:      Security Parameters Index
   SRTP:     Secure Realtime Transport Protocol
   TEK:      Traffic Encryption Key
   TGK:      TEK Generation Key
   TPK:      Ticket Protection Key
   UTC:      Coordinated Universal Time

2.3.  Payloads

   CERTx:    Certificate of entity x
   CHASH:    Hash of the certificate used
   HDR:      Common Header payload
   ID:       Identity payload
   IDRx:     Identifier for entity x
   IDRpsk:   Identifier for pre-shared key
   IDRapp:   Identifier for application/service
   KEMAC:    Key data transport payload



Mattsson & Tian               Informational                     [Page 6]


RFC 6043                      MIKEY-TICKET                    March 2011


   PKE:      Encrypted envelope key
   RAND:     RAND payload
   RANDRx:   Random value generated by entity x
   SIGNx:    Signature created using entity x's private key
   SP:       Security Policy payload
   T:        Timestamp payload
   TRy:      Timestamp payload with role indicator y
   THDR:     Ticket Header payload
   TICKET:   Ticket payload
   TP:       Ticket Policy payload
   V:        Verification payload

   where
      x is in the set {i, r, kms} (Initiator, Responder, KMS) and
      y is in the set {i, s, e, r} (time of Issue, Start time, End time,
         Rekeying interval).

   The IDR, RANDR, TR, TICKET, and TP payloads are defined in Section 6.
   Note that in [RFC3830], there is defined both a V payload (carrying
   the authentication tag) and a V flag in the HDR payload (indicating
   whether or not a response message is expected).

3.  Design Considerations

   As mentioned in the introduction, none of the previously defined
   MIKEY modes are based on a KMS.  The pre-shared key method and the
   public-key encryption method defined in [RFC3830] are examples of
   systems based on pre-distribution of user credentials.  The Diffie-
   Hellman method [RFC3830] is an example of a system based on
   negotiation and exchange directly between peers.

   In some situations, a request may be delivered to multiple endpoints.
   The endpoints may be multiple devices owned by a single user (e.g.,
   mobile phone, fixed phone, and computer), or multiple users (e.g.,
   IT-support@example.com, a group of users where only one is supposed
   to answer).  In the following, the term "forking" will be used to
   describe all such cases.  One example of delivery to multiple
   endpoints is forking and retargeting in SIP [RFC3261].  To prevent
   any form of eavesdropping, only the endpoint that answers should get
   access to the session keys.  The naive application of [RFC3830] where
   all endpoints share the same pre-shared/private key is not secure
   when it comes to forking, as all endpoints get access to the session
   keys.  Conversely, having per-user unique pre-shared keys/
   certificates creates more fundamental problems with forking, as the
   initiator does not know which pre-shared key/certificate to use at
   session initiation.  SIP-signaled media protection is described in
   [RFC5479] and the applicability of different MIKEY modes is discussed
   in [RFC5197].



Mattsson & Tian               Informational                     [Page 7]


RFC 6043                      MIKEY-TICKET                    March 2011


   In security systems serving a large number of users, a solution based
   on a key management service is often preferred.  With such a service
   in place, there is no need to pre-distribute credentials that
   directly can be used to establish security associations between peers
   for protected communication, as users can request such credentials
   when needed.  In many applications, e.g., National Security and
   Public Safety (NSPS), the controlling organization wants to enforce
   policies on the use of keys.  A trusted KMS fits these applications
   well, as it makes it easier to enforce policies centrally.  Solutions
   based on a trusted KMS also scale well when the number of users
   grows.  A KMS based on symmetric keys has particular advantages, as
   symmetric key algorithms are generally much less computationally
   intensive than asymmetric key algorithms.

   Systems based on a KMS require a signaling mechanism that allows
   peers to retrieve other peers' credentials.  A convenient way to
   implement such a signaling scheme is to use a ticket concept, similar
   to that in Kerberos [RFC4120] to identify and deliver keys.  The
   ticket can be forwarded in the signaling associated with the session
   setup.  The initiator requests a ticket from the KMS and sends the
   ticket to the responder.  The responder forwards the ticket to the
   KMS, which returns the corresponding keys.

   It should be noted that Kerberos does not require that the responder
   also contact the KMS.  However, in order to support also the
   aforementioned forking scenarios, it becomes necessary that the
   ticket is not bound to the exact identity (or credentials) of the
   responder until the final responder becomes fully determined.  Group
   and forking communication scenarios can also be improved from access
   control point of view if authorization to access the keys can be
   enforced with higher granularity at the responder side.  The
   mechanism specified in this document is useful for any system where
   the initial message may be transferred to arbitrarily many potential
   responders and where the set of responders may change at any time.
   In addition to being able to meet the requirements just described,
   the mechanism specified in this document also supports group key
   management.

   The ticket can contain a reference to keys held by the key management
   system or it can hold the keys itself.  In the latter case, the
   ticket needs to be confidentiality and integrity protected
   (enveloped).  In the following, the term "encoded keys" will be used
   to describe both cases as well as keys derived from such keys.

   By using different Ticket Types and ticket policies, some allowing
   the initiator or responder to create or resolve the tickets without
   assistance from the KMS, a wide range of different security levels




Mattsson & Tian               Informational                     [Page 8]


RFC 6043                      MIKEY-TICKET                    March 2011


   and use cases can be supported.  This has a number of advantages, as
   it offers a framework that is flexible enough to satisfy users with a
   broad range of security and functional needs.

   The use of a ticket-based system may also help in the handling of
   keys for deferred delivery of end-to-end protected content to
   currently offline users.  Such scenarios exclude all key management
   schemes that are based on some type of direct online negotiation
   between peers (e.g., Diffie-Hellman-based schemes) as the responder
   cannot rely on contacting the initiator to get access to keys.

   At the same time, it is also important to be aware that (centralized)
   key management services may introduce a single point of (security)
   failure.  The security requirements on the implementation and
   protection of the KMS may therefore, in high-security applications,
   be more or less equivalent to the requirements of an AAA
   (Authentication, Authorization, and Accounting) server or a
   Certification Authority (CA).

4.  MIKEY-TICKET

4.1.  Overview

   All previously defined MIKEY modes consist of a single (or half)
   round trip between two peers.  MIKEY-TICKET differs from these modes
   as it consists of up to three different round trips (Ticket Request,
   Ticket Transfer, and Ticket Resolve) involving three parties
   (Initiator, Responder, and KMS).  Since the number of round trips and
   order of messages may vary, MIKEY-TICKET is actually the common name
   for a set of modes, all revolving around a ticket concept.  The third
   party, the KMS, is only involved in some of the MIKEY exchanges and
   not at all in the resulting secure media session.  The Ticket Request
   and Ticket Resolve exchanges are meant to be used in combination with
   the Ticket Transfer exchange and not on their own.  In Figure 1, the
   signaling for the full three round-trip MIKEY-TICKET mode is
   depicted.















Mattsson & Tian               Informational                     [Page 9]


RFC 6043                      MIKEY-TICKET                    March 2011


   +---+                          +-----+                          +---+
   | I |                          | KMS |                          | R |
   +---+                          +-----+                          +---+
               REQUEST_INIT
     -------------------------------->
               REQUEST_RESP
     <--------------------------------
                               TRANSFER_INIT
     ---------------------------------------------------------------->
                                                RESOLVE_INIT
                                     <--------------------------------
                                                RESOLVE_RESP
                                     -------------------------------->
                               TRANSFER_RESP
     <----------------------------------------------------------------

                 Figure 1: Full three round-trip signaling

   The Initiator (I) wants to establish a secure media session with the
   Responder (R).  The Initiator and the Responder do not share any
   credentials; instead, they trust a third party, the KMS, with which
   they both have or can establish shared credentials.  These pre-
   established trust relations are used to establish a security
   association between I and R.  The assumed trust model is illustrated
   in Figure 2.

      Pre-established trust relation   Pre-established trust relation
     <------------------------------> <------------------------------>
   +---+                          +-----+                          +---+
   | I |                          | KMS |                          | R |
   +---+                          +-----+                          +---+
     <--------------------------------------------------------------->
                   Security association based on ticket

                           Figure 2: Trust model

   Note that rather than a single KMS, multiple KMSs may be involved,
   e.g., one for the Initiator and one for the Responder; this is
   discussed in Section 10.

   The Initiator requests keys and a ticket (encoding the same keys)
   from the KMS by sending a REQUEST_INIT message.  The REQUEST_INIT
   message includes session information (e.g., identities of the
   authorized responders) and is integrity protected by a MAC based on a
   pre-shared key or by a signature (similar to the pre-shared key and
   public-key encryption modes in [RFC3830]).  If the request is
   authorized, the KMS generates the requested keys, encodes them in a
   ticket, and returns the keys and the ticket in a REQUEST_RESP



Mattsson & Tian               Informational                    [Page 10]


RFC 6043                      MIKEY-TICKET                    March 2011


   message.  The Ticket Request exchange is OPTIONAL (depending on the
   Ticket Type), and MAY be omitted if the Initiator can create the
   ticket without assistance from the KMS (see mode 3 of Section 4.1.1).

   The Initiator next includes the ticket in a TRANSFER_INIT message,
   which is sent to the Responder.  The TRANSFER_INIT message is
   protected by a MAC based on an MPK (MIKEY Protection Key) encoded in
   the ticket.  If the Responder finds the Ticket Policy and session
   security policies acceptable, the Responder forwards the ticket to
   the KMS.  This is done with a RESOLVE_INIT message, which asks the
   KMS to return the keys encoded in the ticket.  The RESOLVE_INIT
   message is protected by a MAC based on a pre-shared key (between
   Responder and KMS) or by a signature.  The Ticket Resolve exchange is
   OPTIONAL (depending on the Ticket Policy), and SHOULD only be used
   when the Responder is unable to resolve the ticket without assistance
   from the KMS (see mode 2 of Section 4.1.1).

   The KMS resolves the ticket.  If the Responder is authorized to
   receive the keys encoded in the ticket, the KMS retrieves the keys
   and other information.  If key forking is used, the keys are modified
   (bound to the Responder) by the KMS, see Section 5.1.1.  The keys and
   additional information are then sent in a RESOLVE_RESP message to the
   Responder.  The Responder then sends a TRANSFER_RESP message to the
   Initiator as verification.  The TRANSFER_RESP message might include
   information used for further key derivation.

   The use case and signaling described above is the full three round-
   trip mode, but other modes are allowed, see Section 4.1.1.  Pre-
   encrypted content is discussed in Section 8, group communication is
   discussed in Section 9, and signaling between different KMSs is
   discussed in Section 10.  An alternative use case is discussed in
   Appendix B.

   The session keys are normally generated/supplied by the KMS (encoded
   in the ticket), but in certain use cases (see Section 8) the session
   key may be supplied by the Initiator or Responder (sent in a separate
   KEMAC protected with keys derived from the MPK).

   MIKEY-TICKET offers a framework that is flexible enough to satisfy
   users with a broad range of security and functional needs.  The
   framework consists of the three exchanges for which different Ticket
   Types can be defined.  The ticket consists of a Ticket Policy as well
   as Ticket Data.  The Ticket Policy contains information intended for
   all parties involved, whereas the Ticket Data is only intended for
   the party that resolves the ticket.  The Ticket Data could be a
   reference to information (keys, etc.) stored by the key management
   service, it could contain all the information itself, or it could be
   a combination of the two alternatives.  The format of the Ticket Data



Mattsson & Tian               Informational                    [Page 11]


RFC 6043                      MIKEY-TICKET                    March 2011


   depends on the Ticket Type signaled in the Ticket Policy.  The Ticket
   Data corresponding to the default Ticket Type, called MIKEY base
   ticket, is defined in Appendix A and requirements regarding new
   Ticket Types are given in Section 11.

   As MIKEY-TICKET is based on [RFC3830], the same terminology,
   processing, and considerations still apply unless otherwise stated.
   Just like in [RFC3830], the messages are integrity protected and
   encryption is only applied to the keys and not to the entire
   messages.

4.1.1.  Modes

   Depending on the Ticket Type and the Ticket Policy, some of the
   exchanges might be optional or not used at all, see Figure 3.  If the
   ticket protection is based on a key known only by the KMS, both the
   Initiator and the Responder have to contact the KMS to request/
   resolve tickets (mode 1).  If the key used to protect the ticket is
   shared between the KMS and the Responder, the Ticket Resolve exchange
   can be omitted (similar to Kerberos), as the Responder can resolve
   the ticket without assistance from the KMS (mode 2).

     +---+                         +-----+                         +---+
     | I |                         | KMS |                         | R |
     +---+                         +-----+                         +---+
                Ticket Request
   (1) <------------------------------>        Ticket Transfer
       <------------------------------------------------------------->
                                      <------------------------------>
                                               Ticket Resolve
                Ticket Request
   (2) <------------------------------>        Ticket Transfer
       <------------------------------------------------------------->

                               Ticket Transfer
   (3) <------------------------------------------------------------->
                                      <------------------------------>
                                               Ticket Resolve

                               Ticket Transfer
   (4) <------------------------------------------------------------->

                              Figure 3: Modes

   If the key protecting the ticket is shared between the Initiator and
   the KMS, the Ticket Request exchange can be omitted (similar to the
   Otway-Rees protocol [Otway-Rees]), as the Initiator can create the
   ticket without assistance from the KMS (mode 3).  If the key



Mattsson & Tian               Informational                    [Page 12]


RFC 6043                      MIKEY-TICKET                    March 2011


   protecting the ticket is shared between the Initiator and the
   Responder, both the Ticket Request and Ticket Resolve exchanges can
   be omitted (mode 4).  This can be seen as a variation of the pre-
   shared key method of [RFC3830] with a mutual key-freshness guarantee.

   In modes 1 and 2, the Ticket Request exchange can be omitted if the
   tickets and the corresponding keys are distributed from the KMS to
   the Initiator in some other way.  In addition, as tickets may be
   reused (see Section 5.3), a single Ticket Request exchange may be
   followed by several Ticket Transfer exchanges.

4.2.  Exchanges

4.2.1.  Ticket Request

   This exchange is used by the Initiator to request keys and a ticket
   from a trusted KMS with which the Initiator has pre-shared
   credentials.  The request contains information (e.g., participant
   identities, etc.) describing the session the ticket is intended to
   protect.  A full round trip is required for the Initiator to receive
   the ticket.  The initial message REQUEST_INIT comes in two variants.
   The first variant corresponds to the pre-shared key (PSK) method of
   [RFC3830].

   Initiator                               KMS

   REQUEST_INIT_PSK =              ---->
   HDR, T, RANDRi, [IDRi],
      [IDRkms], TP,                 <----  REQUEST_RESP =
      [IDRpsk], V                          HDR, T, [IDRkms],
                                              TICKET, KEMAC, V

   The second variant corresponds to the public-key (PK) method of
   [RFC3830].

   Initiator                               KMS

   REQUEST_INIT_PK =               ---->
   HDR, T, RANDRi, [IDRi],
      {CERTi}, [IDRkms], TP,        <----  REQUEST_RESP =
      [CHASH], PKE, SIGNi                  HDR, T, [IDRkms],
                                              TICKET, KEMAC, V

   As the REQUEST_INIT message MUST ensure the identity of the Initiator
   to the KMS, it SHALL be integrity protected by a MAC based on a pre-
   shared key or by a signature.  The response message REQUEST_RESP is
   the same for the two variants and SHALL be protected using the pre-
   shared/envelope key indicated in the REQUEST_INIT message.



Mattsson & Tian               Informational                    [Page 13]


RFC 6043                      MIKEY-TICKET                    March 2011


   In addition to the ticket, the Initiator receives keys, which it does
   not already know.  The ticket contains both session information and
   information needed to resolve the ticket later, see Section 6.10.

4.2.1.1.  Common Components of the REQUEST_INIT Messages

   The REQUEST_INIT message MUST always include the Header (HDR),
   Timestamp (T), and RANDRi payloads.

   In HDR, the CSB ID (Crypto Session Bundle ID) SHALL be assigned as in
   [RFC3830].  The V flag MUST be set to '1' but SHALL be ignored by the
   KMS as a response is MANDATORY.  As Crypto Sessions (CSs) SHALL NOT
   be handled, the #CS MUST be set to '0' and the CS ID map type SHALL
   be the "Empty map" as defined in [RFC4563].

   IDRi contains the identity of the Initiator.  This identity SHOULD be
   included in the granted Ticket Policy.

   IDRkms contains the identity of the KMS.  It SHOULD be included, but
   it MAY be left out when it can be expected that the KMS has a single
   identity.

   The Ticket Policy payload (TP) contains the desired Ticket Policy.
   It includes for instance, the ticket's validity period, the number of
   requested keys, and the identities of authorized responders (see
   Section 6.10).

4.2.1.2.  Components of the REQUEST_INIT_PSK Message

   The IDRi payload SHOULD be included but MAY be left out when it can
   be expected that the KMS can identify the Initiator by other means.

   The IDRpsk payload is used to indicate the pre-shared key used.  It
   MAY be omitted if the KMS can find the pre-shared key by other means.

   The last payload SHALL be a Verification payload (V) where the
   authentication key (auth_key) is derived from the pre-shared key
   shared by the Initiator and the KMS (see Section 5.1.2 for key
   derivation specification).  The MAC SHALL cover the entire
   REQUEST_INIT_PSK message as well as the identities of the involved
   parties (see Section 5.5 for the exact definition).

4.2.1.3.  Components of the REQUEST_INIT_PK Message

   The identity IDRi and certificate CERTi SHOULD be included, but they
   MAY be left out when it can be expected that the KMS can obtain the
   certificate in some other manner.  If a certificate chain is to be
   provided, each certificate in the chain SHOULD be included in a



Mattsson & Tian               Informational                    [Page 14]


RFC 6043                      MIKEY-TICKET                    March 2011


   separate CERT payload.  The Initiator's certificate MUST come first.
   Each following certificate MUST directly certify the one preceding
   it.

   PKE contains the encrypted envelope key: PKE = E(PKkms, env_key).  It
   is encrypted using the KMS's public key (PKkms).  If the KMS
   possesses several public keys, the Initiator can indicate the key
   used in the CHASH payload.

   SIGNi is a signature covering the entire REQUEST_INIT_PK message,
   using the Initiator's signature key (see Section 5.5 for the exact
   definition).

4.2.1.4.  Processing the REQUEST_INIT Message

   If the KMS can verify the integrity of the received message and the
   message can be correctly parsed, the KMS MUST check the Initiator's
   authorization.  If the Initiator is authorized to receive the
   requested ticket, possibly with a modified Ticket Policy, the KMS
   MUST send a REQUEST_RESP message.  Unexpected payloads in the
   REQUEST_INIT message SHOULD be ignored.  Errors are handled as
   described in Section 5.4.

4.2.1.5.  Components of the REQUEST_RESP Message

   The version, PRF func and CSB ID, #CS, and CS ID map type fields in
   the HDR payload SHALL be identical to the corresponding fields in the
   REQUEST_INIT message.  The V flag has no meaning in this context.  It
   SHALL be set to '0' by the KMS and ignored by the Initiator.

   If one of the NTP timestamp types is used, the KMS SHALL generate a
   fresh timestamp value (unlike [RFC3830]), which may be used for clock
   synchronization.  If the COUNTER timestamp type (see Section 6.6 of
   [RFC3830]) is used, the timestamp value MAY be equal to the one in
   the REQUEST_INIT message.

   The TICKET payload carries the granted Ticket Policy and the Ticket
   Data (see Section 6.10).  As the KMS decides which Ticket Policy to
   use, this may not be the same Ticket Policy as the Initiator
   requested.  The Ticket Type and the Ticket Data depend on the granted
   Ticket Policy.

   The KEMAC payload SHALL use the NULL authentication algorithm, as a
   MAC is included in the V payload.  Depending on the type of
   REQUEST_INIT message, either the pre-shared key or the envelope key
   SHALL be used to derive the encr_key (and salt_key).  Depending on
   the encryption algorithm, the salting key may go into the IV (see
   [RFC3830]).  If the TP payload in the REQUEST_INIT message does not



Mattsson & Tian               Informational                    [Page 15]


RFC 6043                      MIKEY-TICKET                    March 2011


   contain a KEMAC, it is RECOMMENDED that the KMS's default KEMAC
   include a single TGK.  The KEMAC SHALL include an MPK (MIKEY
   Protection Key), MPKi, used as a pre-shared key to protect the
   messages in the Ticket Transfer exchange.  If key forking (see
   Section 5.1.1) is used (determined by the Ticket Policy) a second
   MPK, MPKr, SHALL be included in the KEMAC.  Then, MPKi SHALL be used
   to protect the TRANSFER_INIT message and MPKr SHALL be used to verify
   the TRANSFER_RESP message.  The KEMAC is hence constructed as
   follows:

           KEMAC = E(encr_key, MPKi || [MPKr] || {TEK|TGK|GTGK})

   The last payload SHALL be a Verification payload (V).  Depending on
   the type of REQUEST_INIT message, either the pre-shared key or the
   envelope key SHALL be used to derive the auth_key.  The MAC SHALL
   cover the entire REQUEST_RESP message as well as the REQUEST_INIT
   message (see Section 5.5 for the exact definition).

4.2.1.6.  Processing the REQUEST_RESP Message

   If the Initiator can verify the integrity of the received message and
   the message can be correctly parsed, the ticket and the associated
   session information SHALL be stored.  Unexpected payloads in the
   REQUEST_RESP message SHOULD be ignored.  Errors are handled as
   described in Section 5.4.

   Before using the received ticket, the Initiator MUST check that the
   granted Ticket Policy is acceptable.  If not, the Initiator SHALL
   discard and MAY send a new REQUEST_INIT message suggesting a
   different Ticket Policy than before.

4.2.2.  Ticket Transfer

   This exchange is used to transfer a ticket as well as session
   information from the Initiator to a Responder.  The exchange is
   modeled after the pre-shared key mode [RFC3830], but instead of a
   pre-shared key, an MPK encoded in the ticket is used.  The session
   keys are also encoded in the TICKET payload, but in some use cases
   (see Section 8) they need to be sent in a separate KEMAC payload.
   The session information may be sent from the Initiator to the
   Responder (similar to [RFC3830]) or from the Responder to the
   Initiator (similar to [RFC4738]).  As the motive for this exchange is
   to setup a shared secret key between Initiator and Responder, the
   Responder cannot check the authenticity of the message before the
   ticket is resolved (by KMS or Responder).  A full round trip is
   required if Responder key confirmation and freshness guarantee are
   needed.




Mattsson & Tian               Informational                    [Page 16]


RFC 6043                      MIKEY-TICKET                    March 2011


   Initiator                               Responder

   TRANSFER_INIT =                 ---->
   HDR, T, RANDRi, [IDRi],
      [IDRr], {SP}, TICKET,         < - -  TRANSFER_RESP =
      [KEMAC], V                           HDR, T, [RANDRr],
                                              [IDRr], [RANDRkms],
                                              {SP}, [KEMAC], V

4.2.2.1.  Components of the TRANSFER_INIT Message

   The TRANSFER_INIT message MUST always include the Header (HDR),
   Timestamp (T), and RANDRi payloads.

   In HDR, the CSB ID (Crypto Session Bundle ID) SHALL be assigned as in
   [RFC3830].  The value of the V flag SHALL agree with the F flag in
   the Ticket Policy and it SHALL be ignored by the Responder.

   The IDRi and IDRr payloads SHOULD be included, but IDRi MAY be left
   out if the Responder can identify the Initiator by other means, and
   IDRr MAY be left out when it can be expected that the Responder has a
   single identity.

   Multiple SP payloads MAY be used both to indicate supported security
   policies for a specific crypto session (similar to [RFC4738]) and to
   specify security policies for different crypto sessions (similar to
   [RFC3830]).

   The ticket payload (see Section 6.10) contains the Ticket Policy (see
   Section 6.10), Ticket Data (the default ticket type is defined in
   Appendix A), and Initiator Data.  The Ticket Policy contains
   information intended for all parties involved, whereas the Ticket
   Data is only intended for the party that resolves the ticket.  The
   Ticket Type provided in the Ticket Data is indicated in the Ticket
   Policy.  The Initiator Data authenticates the Initiator when key
   forking (I flag) is used.

   The KEMAC payload is handled in the same way as if it were sent in a
   later CSB update (see Section 5.2), with the only difference that the
   encr_key is always derived from MPKi and therefore accessible by all
   responders authorized to resolve the ticket.  Initiator-specified
   keys MAY be used if the Initiator has pre-encrypted content and
   specific TEKs (Traffic Encryption Keys) need to be used (see
   Section 8).  If indicated by the Ticket Policy (L flag), a KEMAC
   payload SHALL NOT be included.






Mattsson & Tian               Informational                    [Page 17]


RFC 6043                      MIKEY-TICKET                    March 2011


   The last payload SHALL be a Verification payload (V) where the
   authentication key (auth_key) is derived from the MPKi (see
   Section 5.1.2 for key derivation specification).  The MAC SHALL cover
   the entire TRANSFER_INIT message as well as the identities of the
   involved parties (see Section 5.5 for the exact definition).

4.2.2.2.  Processing the TRANSFER_INIT Message

   As the Initiator and Responder do not have any pre-shared keys, the
   Responder cannot check the authenticity of the message before the
   ticket is resolved.  The Responder SHALL however check that both the
   Ticket Policy and the security policies are acceptable.  If they are
   not, the Responder SHALL reject without contacting the KMS.  This is
   an early reject mechanism to avoid unnecessary KMS signaling when the
   Responder can conclude from the information at hand that it will not
   accept the connection.  After the ticket has been resolved, the
   parsing of the TRANSFER_INIT message continues.  Unexpected payloads
   in the TRANSFER_INIT message SHOULD be ignored.  Errors are handled
   as described in Section 5.4.  If the F flag in the Ticket Policy is
   set, the Responder MUST send a TRANSFER_RESP message.

4.2.2.3.  Components of the TRANSFER_RESP Message

   The version, PRF func and CSB ID fields in the HDR payload SHALL be
   identical to the corresponding fields in the TRANSFER_INIT message.
   The V flag has no meaning in this context.  It SHALL be set to '0' by
   the Responder and ignored by the Initiator.  The Responder SHALL
   update the CS ID map info so that each crypto session has exactly one
   security policy indicated.  The Responder MUST provide Session Data
   (at least for SRTP) and SPI for each crypto session for which the
   Initiator has not supplied Session Data and SPI.  If needed, the
   Responder MAY update Session Data and SPI provided by the Initiator.
   If the Responder adds crypto sessions, the #CS SHALL be updated.

   If one of the NTP timestamp types is used, the Responder SHALL
   generate a fresh timestamp value (unlike [RFC3830]).  If the COUNTER
   timestamp type (see Section 6.6 of [RFC3830]) is used, the timestamp
   value MAY be equal to the one in the TRANSFER_INIT message.

   If indicated by the Ticket Policy (G flag), the Responder SHALL
   generate a fresh (pseudo-)random byte string RANDRr.  RANDRr is used
   to produce Responder freshness guarantee in key derivations.

   If the Responder receives an IDRr payload in the RESOLVE_RESP
   message, the same identity MUST be sent in an IDRr payload in the
   TRANSFER_RESP message.  The identity sent in the IDRr payload in the





Mattsson & Tian               Informational                    [Page 18]


RFC 6043                      MIKEY-TICKET                    March 2011


   TRANSFER_RESP message (e.g., user1@example.com) MAY differ from the
   one sent in the IDRr payload in the TRANSFER_INIT message (e.g.,
   IT-support@example.com).

   If the Responder receives a RANDRkms payload in the RESOLVE_RESP
   message, the same RAND MUST be sent in a RANDRkms payload in the
   TRANSFER_RESP message.

   The Responder MAY provide additional Security Policy payloads.  The
   Responder SHOULD NOT resend SP payloads, which the Initiator
   supplied.

   The KEMAC payload SHALL be handled exactly as if it was sent in a
   later CSB update, see Section 5.2.  Responder-specified keys MAY be
   used if Responder has pre-encrypted content and specific TEKs
   (Traffic Encryption Keys) need to be used (see Section 8).  If
   indicated by the Ticket Policy (M flag), a KEMAC payload SHALL NOT be
   included.

   The last payload SHALL be a Verification payload (V) where the
   authentication key (auth_key) is derived from MPKi or MPKr'
   (depending on if key forking is used).  The MAC SHALL cover the
   entire TRANSFER_RESP message as well as the TRANSFER_INIT message
   (see Section 5.5 for the exact definition).

4.2.2.4.  Processing the TRANSFER_RESP Message

   If the Initiator can verify the integrity of the received message and
   the message can be correctly parsed, the Initiator MUST check that
   any Responder-generated security policies are acceptable.  If not,
   the Initiator SHALL discard and MAY send a new TRANSFER_INIT message
   to indicate supported security policies.  Unexpected payloads in the
   TRANSFER_RESP message SHOULD be ignored.  Errors are handled as
   described in Section 5.4.

4.2.3.  Ticket Resolve

   This exchange is used by the Responder to request that the KMS return
   the keys encoded in a ticket.  The KMS does not need to be the same
   KMS that originally issued the ticket, see Section 10.  A full round
   trip is required for the Responder to receive the keys.  The Ticket
   Resolve exchange is OPTIONAL (depending on the Ticket Policy), and
   SHOULD only be used when the Responder is unable to resolve the
   ticket without assistance from the KMS.  The initial message
   RESOLVE_INIT comes in two variants (independent from the used
   REQUEST_INIT variant).  The first variant corresponds to the pre-
   shared key (PSK) method of [RFC3830].




Mattsson & Tian               Informational                    [Page 19]


RFC 6043                      MIKEY-TICKET                    March 2011


   Responder                               KMS

   RESOLVE_INIT_PSK =              ---->
   HDR, T, RANDRr, [IDRr],
      [IDRkms], TICKET,             <----  RESOLVE_RESP
      [IDRpsk], V                          HDR, T, [IDRkms], KEMAC,
                                              [IDRr], [RANDRkms], V

   The second variant corresponds to the public-key (PK) method of
   [RFC3830].

   Responder                               KMS

   RESOLVE_INIT_PK =               ---->
   HDR, T, RANDRr, [IDRr],
      {CERTr}, [IDRkms], TICKET,    <----  RESOLVE_RESP
      [CHASH], PKE, SIGNr                  HDR, T, [IDRkms], KEMAC,
                                              [IDRr], [RANDRkms], V

   As the RESOLVE_INIT message MUST ensure the identity of the Responder
   to the KMS, it SHALL be protected by a MAC based on a pre-shared key
   or by a signature.  The response message RESOLVE_RESP is the same for
   the two variants and SHALL be protected by using the pre-shared/
   envelope key indicated in the RESOLVE_INIT message.

   Upon receiving the RESOLVE_INIT message, the KMS verifies that the
   Responder is authorized to resolve the ticket based on ticket and KMS
   policies.  The KMS extracts the session information from the ticket
   and returns this to the Responder.  Since the KMS resolved the
   ticket, the Responder is assured of the integrity of the Ticket
   Policy, which contains the identity of the peer that requested or
   created the ticket.  If key forking is used (I flag), the Responder
   is also assured that the peer that requested or created the ticket
   also sent the TRANSFER_INIT message.  The Responder can complete the
   session information it got from the Initiator with the additional
   session information received from the KMS.

4.2.3.1.  Common Components of the RESOLVE_INIT Messages

   The RESOLVE_INIT message MUST always include the Header (HDR),
   Timestamp (T), and RANDRr payloads.

   The CSB ID (Crypto Session Bundle ID) SHALL be assigned as in
   [RFC3830].  The V flag MUST be set to '1' but SHALL be ignored by the
   KMS as a response is MANDATORY.  As crypto sessions SHALL NOT be
   handled, the #CS MUST be set to '0' and the CS ID map type SHALL be
   the "Empty map" as defined in [RFC4563].




Mattsson & Tian               Informational                    [Page 20]


RFC 6043                      MIKEY-TICKET                    March 2011


   IDRkms SHOULD be included, but it MAY be left out when it can be
   expected that the KMS has a single identity.

   The TICKET payload contains the Ticket Policy and Ticket Data that
   the Responder wants to have resolved.

4.2.3.2.  Components of the RESOLVE_INIT_PSK Message

   IDRr contains the identity of the Responder.  IDRr SHOULD be
   included, but it MAY be left out when it can be expected that the KMS
   can identify the Responder in some other manner.

   The IDRpsk payload is used to indicate the pre-shared key used.  It
   MAY be omitted if the KMS can find the pre-shared key by other means.

   The last payload SHALL be a Verification payload (V) where the
   authentication key (auth_key) is derived from the pre-shared key
   shared by the Responder and the KMS.  The MAC SHALL cover the entire
   RESOLVE_INIT_PSK message as well as the identities of the involved
   parties (see Section 5.5 for the exact definition).

4.2.3.3.  Components of the RESOLVE_INIT_PK Message

   The identity IDRr and certificate CERTr SHOULD be included, but they
   MAY be left out when it can be expected that the KMS can obtain the
   certificate in some other manner.  If a certificate chain is to be
   provided, each certificate in the chain SHOULD be included in a
   separate CERT payload.  The Responder's certificate MUST come first.
   Each following certificate MUST directly certify the one preceding
   it.

   PKE contains the encrypted envelope key: PKE = E(PKkms, env_key).  It
   is encrypted using PKkms.  If the KMS possesses several public keys,
   the Responder can indicate the key used in the CHASH payload.

   SIGNr is a signature covering the entire RESOLVE_INIT_PK message,
   using the Responder's signature key (see Section 5.5 for the exact
   definition).

4.2.3.4.  Processing the RESOLVE_INIT Message

   If the KMS can verify the integrity of the received message, the
   message can be correctly parsed, and the Responder is authorized to
   resolve the ticket, the KMS MUST send a RESOLVE_RESP message.  If key
   forking is used (I flag), the KMS SHALL also verify the integrity of
   the Initiator Data field in the TICKET payload.  Unexpected payloads
   in the RESOLVE_INIT message SHOULD be ignored.  Errors are handled as
   described in Section 5.4.



Mattsson & Tian               Informational                    [Page 21]


RFC 6043                      MIKEY-TICKET                    March 2011


4.2.3.5.  Components of the RESOLVE_RESP Message

   The version, PRF func and CSB ID, #CS, and CS ID map type fields in
   the HDR payload SHALL be identical to the corresponding fields in the
   RESOLVE_INIT message.  The V flag has no meaning in this context.  It
   SHALL be set to '0' by the KMS and ignored by the Responder.

   If one of the NTP timestamp types is used, the KMS SHALL generate a
   fresh timestamp value (unlike [RFC3830]), which may be used for clock
   synchronization.  If the COUNTER timestamp type (see Section 6.6 of
   [RFC3830]) is used, the timestamp value MAY be equal to the one in
   the RESOLVE_INIT message.

   The KEMAC payload SHALL use the NULL authentication algorithm, as a
   MAC is included in the V payload.  Depending on the type of
   RESOLVE_INIT message, either the pre-shared key or the envelope key
   SHALL be used to derive the encr_key (and salt_key).  Depending on
   the encryption algorithm, the salting key may go into the IV (see
   [RFC3830]).  The KEMAC SHALL include an MPK (MPKi), used as a pre-
   shared key to protect the messages in the Ticket Transfer exchange.
   The KEMAC is hence constructed as follows:

           KEMAC = E(encr_key, MPKi || [MPKr'] || {TEK|TGK|GTGK})

   If key forking (see Section 5.1.1) is used (determined by the I flag
   in the Ticket Policy), a second MPK (MPKr') SHALL be included in the
   KEMAC.  Then, MPKi SHALL be used to verify the TRANSFER_INIT message
   and MPKr' SHALL be used to protect the TRANSFER_RESP message.  The
   KMS SHALL also fork the MPKr and the TGKs.  The modifier used to
   derive the forked keys SHALL be included in the IDRr and RANDRkms
   payloads, where IDRr is the identity of the endpoint that answered
   and RANDRkms is a fresh (pseudo-)random byte string generated by the
   KMS.  The reason that the KMS MAY adjust the Responder's identity is
   so that it matches an identity encoded in the ticket.

   The last payload SHALL be a Verification payload (V).  Depending on
   the type of RESOLVE_INIT message, either the pre-shared key or the
   envelope key SHALL be used to derive the auth_key.  The MAC SHALL
   cover the entire RESOLVE_RESP message as well as the RESOLVE_INIT
   message (see Section 5.5 for the exact definition).

4.2.3.6.  Processing the RESOLVE_RESP Message

   If the Responder can verify the integrity of the received message and
   the message can be correctly parsed, the Responder MUST verify the
   TRANSFER_INIT message with the MPKi received from the KMS.  If key
   forking is used, the Responder SHALL also verify that the MAC field
   in the V payload in the TRANSFER_INIT message is identical to the MAC



Mattsson & Tian               Informational                    [Page 22]


RFC 6043                      MIKEY-TICKET                    March 2011


   field in the Vi payload in the Initiator Data field in the TICKET
   payload.  Unexpected payloads in the RESOLVE_RESP message SHOULD be
   ignored.  Errors are handled as described in Section 5.4.

5.  Key Management Functions

5.1.  Key Derivation

   For all messages in the Ticket Request and Ticket Resolve exchanges,
   the keys used to protect the MIKEY messages are derived from a pre-
   shared key or an envelope key.  As crypto sessions SHALL NOT be
   handled, further keying material (i.e., TEKs) does not have to be
   derived.

   In the Ticket Transfer exchange, the keys used to protect the MIKEY
   messages are derived from an MPK.  If key forking is used, the KMS
   and the Initiator SHALL fork the MPKr and the TGKs (encoded in the
   ticket) based on a modifier, and different MPKs (MPKi and MPKr')
   SHALL be used to protect the TRANSFER_INIT and TRANSFER_RESP
   messages.  In addition, the Responder MAY generate a RAND used to
   give Responder key freshness guarantee.

   The key hierarchy and its dependencies on TRANSFER_INIT message
   contents for the case without key forking and RANDRr are illustrated
   in Figure 4.  The KEMAC shown is the KEMAC sent from the KMS to the
   Initiator and the Responder.  The illustrated key derivations are
   done by the Initiator and the Responder.
























Mattsson & Tian               Informational                    [Page 23]


RFC 6043                      MIKEY-TICKET                    March 2011


                                +------+------------------+-----+------+
   KEMAC                        | MPKi |..................| TGK | SALT |
                                +--+---+------------------+--+--+--+---+
                                   | MPKi                    |     |
                                   v                         |     |
                       CSB ID    -----   auth_key    ------  |     |
                    +---------->| PRF |------------>| AUTH | |     |
                    |            -----               ------  |     |
                    |              ^                MAC |    |     |
                    |              | RAND               v    |     |
                 +--+--+------+----+---+--+--------+--+---+  |     |
   TRANSFER_INIT | HDR |......| RANDRi |..| TICKET |..| V |  |     |
                 +--+--+------+----+---+--+--------+--+---+  |     |
                    |              | RAND                    |     |
                    |              v                         |     |
                    |   CS ID    -----           TGK         |     |
                    +---------->| PRF |<---------------------+     |
                                 -----                             |
                                   | TEK                      SALT |
                                   v                               v
                                ---------------------------------------
                               |      Security Protocol, e.g., SRTP    |
                                ---------------------------------------

          Figure 4: Key hierarchy without key forking and RANDRr

   The key hierarchy and its dependencies on TRANSFER_RESP message
   contents for the case with key forking and RANDRr are illustrated in
   Figure 5.  The KEMAC shown is the KEMAC sent from the KMS to the
   Initiator.  MOD is the modifier (IDRr, RANDRkms).  The two key
   derivations that produce forked keys are done by the Initiator and
   the KMS, and the remaining two key derivations are done by the
   Initiator and the Responder.  The random value RANDRi from the
   TRANSFER_INIT message is used as input to the derivation of the
   auth_key and may be used as input to the derivation of the TEK, but
   this is omitted from the figure.  The protection of the TRANSFER_INIT
   message is done as in Figure 4.














Mattsson & Tian               Informational                    [Page 24]


RFC 6043                      MIKEY-TICKET                    March 2011


                        +------+--------------------------+-----+------+
KEMAC                   | MPKr |..........................| TGK | SALT |
                        +--+---+--------------------------+--+--+--+---+
                           | MPKr                            |     |
                           v                                 |     |
                         -----   MPKr'                       |     |
                        | PRF |-------+                  TGK |     |
                         -----        |                      |     |
                           ^          v                      |     |
                   CSB ID  |        -----  auth_key  ------  |     |
                 +---------)------>| PRF |--------->| AUTH | |     |
                 |         |        -----            ------  |     |
                 |         | ID Data  ^             MAC |    |     |
                 |         | RAND     | RAND            v    |     |
              +--+--+---+--+--+---+---+----+----------+---+  |     |
TRANSFER_RESP | HDR |...| MOD |...| RANDRr |..........| V |  |     |
              +--+--+---+--+--+---+---+----+----------+---+  |     |
                 |         |          | RAND                 v     |
                 |         |          |          ID Data   -----   |
                 |         +----------)------------------>| PRF |  |
                 |                    |            RAND    -----   |
                 |                    v                      |     |
                 |       CS ID      -----         TGK'       |     |
                 +---------------->| PRF |<------------------+     |
                                    -----                          |
                                      | TEK                   SALT |
                                      v                            v
                                ---------------------------------------
                               |      Security Protocol, e.g., SRTP    |
                                ---------------------------------------

            Figure 5: Key hierarchy with key forking and RANDRr

   The labels in the key derivations SHALL NOT include entire RANDR
   payloads, only the fields RAND length and RAND from the corresponding
   payload.

5.1.1.  Deriving Forked Keys

   When key forking is used (determined by the I flag in the Ticket
   Policy), the MPKr and TGKs (encoded in the ticket) SHALL be forked.
   The TEKs and GTGKs (Group TGKs), however, SHALL NOT be forked.  This
   key forking is done by the KMS and the Initiator using the PRF
   (Pseudorandom Function) indicated in the Ticket Policy.  The
   parameters for the PRF are:






Mattsson & Tian               Informational                    [Page 25]


RFC 6043                      MIKEY-TICKET                    March 2011


   inkey:     : MPKr or TGK
   inkey_len  : bit length of the inkey
   label      : constant || 0xFF || 0xFFFFFFFF || 0x00 ||
                length ID Data || ID Data || length RANDRkms || RANDRkms
   outkey_len : desired bit length of the outkey (MPKr', TGK')
                SHALL be equal to inkey_len

   where the ID Data field is taken from the IDRr payload sent in the
   RESOLVE_RESP and TRANSFER_RESP messages.  Length ID Data is the
   length of the ID Data field in bytes as a 16-bit unsigned integer.
   Length RANDRkms is the length of RANDRkms in bytes as an 8-bit
   unsigned integer.  The constant depends on the derived key type as
   summarized below.

                          Derived key | Constant
                          ------------+-----------
                          MPKr'       | 0x2B288856
                          TGK'        | 0x1512B54A

              Table 5.1: Constants for forking key derivation

   The constants are taken from the decimal digits of e as described in
   [RFC3830].

5.1.2.  Deriving Keys from an Envelope Key/PSK/MPK

   This derivation is used to form the keys used to protect the MIKEY
   messages.  For the Ticket Request and Ticket Resolve exchanges, the
   keys used to protect the MIKEY messages are derived from a pre-shared
   key or an envelope key.  For the Ticket Transfer exchange, the keys
   are derived from an MPK.  If key forking is used, different MPKs
   (MPKi and MPKr') SHALL be used to protect the TRANSFER_INIT and
   TRANSFER_RESP messages.  The initial messages SHALL be protected with
   keys derived using the following parameters:

   inkey:     : pre-shared key, envelope key, or MPKi
   inkey_len  : bit length of the inkey
   label      : constant || 0xFF || CSB ID || 0x01 ||
                length RANDRi || [RANDRi] || length RANDRr || [RANDRr]
   outkey_len : desired bit length of the outkey (encr_key,
                auth_key, salt_key)

   The response messages SHALL be protected with keys derived using the
   following parameters:







Mattsson & Tian               Informational                    [Page 26]


RFC 6043                      MIKEY-TICKET                    March 2011


   inkey:     : pre-shared key, envelope key, MPKi, or MPKr'
   inkey_len  : bit length of the inkey
   label      : constant || 0xFF || CSB ID || 0x02 ||
                length RANDRi || [RANDRi] || length RANDRr || [RANDRr]
   outkey_len : desired bit length of the outkey (encr_key,
                auth_key, salt_key)

   The constant depends on the derived key type as defined in Section
   4.1.4 of [RFC3830].  The 32-bit CSB ID field is taken from the HDR
   payload.  RANDRi SHALL be included in the derivation of keys used to
   protect the Ticket Request and Ticket Transfer exchanges.  RANDRr
   SHALL be included in the derivation of keys used to protect the
   Ticket Resolve exchange and in the derivation of keys used to protect
   TRANSFER_RESP if the Ticket Policy determines that it shall be
   present in the TRANSFER_RESP message (G flag).  Length RANDRi is the
   length of RANDRi in bytes as an 8-bit unsigned integer, and Length
   RANDRr is the length of RANDRr in bytes as an 8-bit unsigned integer.
   If RANDRi is omitted, length RANDRi SHALL be 0 and if RANDRr is
   omitted, length RANDRr SHALL be 0.  Note that at least one of RANDRi
   and RANDRr is always used.

5.1.3.  Deriving Keys from a TGK/GTGK

   This only affects the Ticket Transfer exchange.  In the following, we
   describe how keying material is derived from a TGK/GTGK.  If key
   forking is used, any TGK encoded in the ticket SHALL be forked, and
   the forked key TGK' SHALL be used.  The key derivation method SHALL
   be executed using the PRF indicated in the HDR payload.  The
   parameters for the PRF are:

   inkey:     : TGK, TGK', or GTGK
   inkey_len  : bit length of the inkey
   label      : constant || CS ID || 0xFFFFFFFF || 0x03 ||
                length RANDRi || [RANDRi] || length RANDRr || [RANDRr]
   outkey_len : desired bit length of the outkey (TEK, encr_key,
                auth_key, salt_key)

   The constant depends on the derived key type as defined in Section
   4.1.3 of [RFC3830].  If a salting key is present in the key data sub-
   payload, a security protocol in need of a salting key SHALL use this
   salting key and a new salting key SHALL NOT be derived.  The 8-bit CS
   ID field is given by the CS ID map info field in the HDR payload.
   RANDRi SHALL be included if the Ticket Policy determines that it
   shall be used (H flag).  RANDRr SHALL be included if the Ticket
   Policy determines that it shall be present in the TRANSFER_RESP
   message (G flag).  Length RANDRi is the length of RANDRi in bytes as
   an 8-bit unsigned integer, and Length RANDRr is the length of RANDRr




Mattsson & Tian               Informational                    [Page 27]


RFC 6043                      MIKEY-TICKET                    March 2011


   in bytes as an 8-bit unsigned integer.  If RANDRi or RANDRr is
   omitted the corresponding length SHALL be 0.  Note that at least one
   of RANDRi and RANDRr MUST be used.

5.2.  CSB Updating

   Similar to [RFC3830], MIKEY-TICKET provides a means of updating the
   CSB (Crypto Session Bundle), e.g., transporting a new TEK/TGK/GTGK or
   adding new crypto sessions.  The CSB updating is done by executing
   the Ticket Transfer exchange again, e.g., before a TEK expires or
   when a new crypto session is needed.  The CSB updating can be started
   by the Initiator:

   Initiator                               Responder

   TRANSFER_INIT =                 ---->
   HDR, T, [IDRi], [IDRr],
      {SP}, [KEMAC], V              < - -  TRANSFER_RESP =
                                           HDR, T, [IDRr],
                                           {SP}, [KEMAC], V

   The CSB updating can also be started by the Responder:

   Responder                               Initiator

   TRANSFER_INIT =                 ---->
   HDR, T, [IDRr], [IDRi],
      {SP}, [KEMAC], V              < - -  TRANSFER_RESP =
                                           HDR, T, [IDRi],
                                           {SP}, [KEMAC], V

   The new message exchange MUST use the same CSB ID as the initial
   exchange but MUST use new timestamps.  The crypto sessions
   negotiation (#CS field, CS ID map info field, and SP payloads) are
   handled as in the initial exchange.  In the TRANSFER_INIT message the
   V flag SHALL be used to indicate whether or not a response message is
   expected.  Static payloads such as RANDRi, RANDRr, RANDRkms, and
   TICKET that were provided in the initial exchange SHOULD NOT be
   included unless they are needed by a specific use case.  New RANDs or
   TICKETs MUST NOT be included.  The reason that new RANDs SHALL NOT be
   used is that if several TGKs are used, the peers would need to keep
   track of which RANDs to use for each TGK.  This adds unnecessary
   complexity.  Both messages SHALL be protected with the same keys
   (derived from MPKi or MPKr') that protected the last message
   (TRANSFER_INIT or TRANSFER_RESP) in the initial exchange.






Mattsson & Tian               Informational                    [Page 28]


RFC 6043                      MIKEY-TICKET                    March 2011


   New keying material MAY be sent in a KEMAC payload.  If indicated by
   the Ticket Policy (L and M flags), KEMAC payloads SHALL NOT be
   included.  In the TRANSFER_RESP message, a session key MUST be
   provided for each crypto session.  The KEMAC SHALL use the NULL
   authentication algorithm, as a MAC is included in the V payload.  The
   encr_key (and salt_key) SHALL be derived from the MPK (MPKi or
   MPKr').  Depending on the encryption algorithm, the salting key may
   go into the IV (see [RFC3830]).  If a new TGK is exchanged, it SHALL
   NOT be forked.  The KEMAC is hence constructed as follows:

                    KEMAC = E(encr_key, (TEK|TGK|GTGK))

5.3.  Ticket Reuse

   MIKEY-TICKET includes features aiming to offload the KMS from
   receiving ticket requests.  One such feature is that tickets may be
   reused.  This means that a user may request a ticket for media
   sessions with another user and then under the ticket's validity
   period use this ticket to protect several media sessions with that
   user.

   When reusing a ticket that has been used in a previous Ticket
   Transfer exchange, a new Ticket Transfer exchange is executed.  The
   new exchange MUST use a new CSB ID, a new timestamp, and new RANDs
   (RANDRi, RANDRr).  If the Responder has resolved the ticket before,
   the Responder does not need to resolve the ticket again.  In that
   case, the same modifier (IDRr, RANDRkms) SHALL be used.  If the
   Ticket Policy forbids reuse (J flag), the ticket MUST NOT be reused.
   Note that such reuse cannot be detected by a stateless KMS.  When
   group keys are used, ticket reuse leaves the Initiator responsible to
   ensure that group membership has not changed since the ticket was
   last used.  (Otherwise, unauthorized responders may gain access to
   the group communication.)  Thus, if group dynamics are difficult to
   verify, the Initiator SHOULD NOT initiate ticket reuse.

   When key forking is used, only the user that requested the ticket has
   access to the encoded master keys (MPKr, TGKs).  Because of this, no
   one else can initiate a Ticket Transfer exchange using the ticket.

5.4.  Error Handling

   If a fatal error occurs during the parsing of a message, the message
   SHOULD be discarded, and an Error message SHOULD be sent to the other
   party (Initiator, Responder, KMS).  If a failure is due to the
   inability to authenticate the peer, the message SHALL be discarded,
   the Error message is OPTIONAL, and the caveats in Section 5.1.2 of
   [RFC3830] apply.  Error messages may be used to report errors in both
   initial and response messages, but not in Error messages.



Mattsson & Tian               Informational                    [Page 29]


RFC 6043                      MIKEY-TICKET                    March 2011


   In the Ticket Request and Ticket Resolve exchanges, the Error message
   MAY be authenticated with a MAC or a signature.  The Error message is
   hence constructed as follows:

                  Error message = HDR, T, (ERR), [V|SIGNx]

   where x is in the set {i, r, kms} (Initiator, Responder, KMS).
   Unexpected payloads in the Error message SHOULD be ignored.

   In the Ticket Transfer exchange, the Error message MAY be
   authenticated with a MAC.  If the suggested security policies are not
   supported, the Error message SHOULD include the supported parameters.
   The Error message is hence constructed as follows:

                  Error message = HDR, T, (ERR), {SP}, [V]

   In Error messages, the version, PRF func, and CSB ID fields in the
   HDR payload SHALL be identical to the corresponding fields in the
   message where the error occurred.  The V field SHALL be set to '0'
   and be ignored.

   If one of the NTP timestamp types is used, a fresh timestamp value
   SHALL be used.  If the COUNTER timestamp type (see Section 6.6 of
   [RFC3830]) is used, the timestamp value MAY be equal to the one in
   the message where the error occurred.

   The MAC/Signature in the V/SIGN payloads covers the entire Error
   message, except the MAC/Signature field itself.  The auth_key SHALL
   be the same as in the message where the error occurred.

5.5.  MAC/Signature Coverage

   The MAC/Signature in the V/SIGN payloads covers the entire MIKEY
   message, except the MAC/Signature field itself.  For initial
   messages, the identities (not whole payloads) of the parties involved
   MUST directly follow the MIKEY message in the Verification MAC/
   Signature calculation.  In the TRANSFER_INIT message, the MAC SHALL
   NOT cover the Initiator Data length and Initiator Data fields in the
   TICKET payload.  Note that in the Transfer Exchange, Identity_r in
   TRANSFER_RESP (e.g., user1@example.com) MAY differ from that
   appearing in TRANSFER_INIT (e.g., IT-support@example.com).  For
   response messages, the entire initial message (including the MAC/
   Signature field) MUST directly follow the MIKEY message in the
   Verification MAC/Signature calculation (the identities are implicitly
   covered as they are covered by the initial message's MAC/Signature).






Mattsson & Tian               Informational                    [Page 30]


RFC 6043                      MIKEY-TICKET                    March 2011


        Message type  | MAC/Signature coverage
        --------------+--------------------------------------------
        REQUEST_INIT  | REQUEST_INIT  || Identity_i || Identity_kms
        REQUEST_RESP  | REQUEST_RESP  || REQUEST_INIT
        TRANSFER_INIT | TRANSFER_INIT || Identity_i || Identity_r
        TRANSFER_RESP | TRANSFER_RESP || TRANSFER_INIT
        RESOLVE_INIT  | RESOLVE_INIT  || Identity_r || Identity_kms
        RESOLVE_RESP  | RESOLVE_RESP  || RESOLVE_INIT
        Error message | Error message

                     Table 5.2: MAC/Signature coverage

6.  Payload Encoding

   This section does not describe all the payloads that are used in the
   new message types.  It describes in detail the new TR, IDR, RANDR,
   TP, and TICKET payloads.  For the other payloads, only the additions
   and changes compared to [RFC3830] are described.  For a detailed
   description of the other MIKEY payloads, see [RFC3830].  Note that
   the fields with variable length are byte aligned and not 32-bit
   aligned.

6.1.  Common Header Payload (HDR)

   For the Common Header Payload, new values are added to the Data Type,
   Next Payload, PRF func, and CS ID map type name spaces.

   *  Data Type (8 bits): describes the type of message.

      Data Type        | Value | Comment
      -----------------+-------+-------------------------------------
      REQUEST_INIT_PSK |    11 | Ticket request initial message (PSK)
      REQUEST_INIT_PK  |    12 | Ticket request initial message (PK)
      REQUEST_RESP     |    13 | Ticket request response message
                       |       |
      TRANSFER_INIT    |    14 | Ticket transfer initial message
      TRANSFER_RESP    |    15 | Ticket transfer response message
                       |       |
      RESOLVE_INIT_PSK |    16 | Ticket resolve initial message (PSK)
      RESOLVE_INIT_PK  |    17 | Ticket resolve initial message (PK)
      RESOLVE_RESP     |    18 | Ticket resolve response message

                     Table 6.1: Data Type (Additions)








Mattsson & Tian               Informational                    [Page 31]


RFC 6043                      MIKEY-TICKET                    March 2011


   *  Next Payload (8 bits): identifies the payload that is added after
      this payload.

                       Next Payload | Value | Section
                       -------------+-------+--------
                       TR           |    13 | 6.4
                       IDR          |    14 | 6.6
                       RANDR        |    15 | 6.8
                       TP           |    16 | 6.10
                       TICKET       |    17 | 6.10

                    Table 6.2: Next Payload (Additions)

   *  V (1 bit): flag to indicate whether a response message is expected
      ('1') or not ('0').  It MUST be set to '0' and ignored in all
      messages except TRANSFER_INIT messages used for CSB updating (see
      Section 5.2).

   *  PRF func (7 bits): indicates the PRF function that has been/will
      be used for key derivation.  Besides the PRFs already defined in
      [RFC3830] the following additional PRF may be used.

                         PRF func         | Value
                         -----------------+------
                         PRF-HMAC-SHA-256 |     1

                      Table 6.3: PRF func (Additions)

   The new PRF SHALL be constructed as described in Section 4.1.2 of
   [RFC3830] with the differences that HMAC-SHA-256 (see Section 6.2)
   SHALL be used instead of HMAC-SHA-1 and the value 256 SHALL be used
   instead of 160.  This corresponds to the full output length of
   SHA-256.

   *  #CS (8 bits): indicates the number of crypto sessions in the CS ID
      map info.

   *  CS ID map type (8 bits): specifies the method of uniquely mapping
      crypto sessions to the security protocol sessions.  In the Ticket
      Transfer exchange the new GENERIC-ID map type, which is intended
      to eliminate the limitations with the existing SRTP-ID map type,
      SHOULD be used.  The map type SRTP-ID SHALL NOT be used.

                          CS ID map type | Value
                          ----------------------
                          GENERIC-ID     |     2

                   Table 6.4: CS ID map type (Additions)



Mattsson & Tian               Informational                    [Page 32]


RFC 6043                      MIKEY-TICKET                    March 2011


   *  CS ID map info (variable length): identifies and maps the crypto
      sessions to the security protocol sessions for which security
      associations should be created.

6.1.1.  The GENERIC-ID Map Type

   For the GENERIC-ID map type, the CS ID map info consists of #CS
   number of blocks, each mapping policies, session data (e.g., SSRC),
   and key to a specific crypto session.

    0                   1                   2                   3
    0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   !     CS ID     !   Prot type   !S!     #P      ! Ps (OPTIONAL) ~
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   !      Session Data Length      !    Session Data (OPTIONAL)    ~
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   !  SPI Length   !                SPI (OPTIONAL)                 ~
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

   *  CS ID (8 bits): defines the CS ID to be used for the crypto
      session.

   *  Prot type (8 bits): defines the security protocol to be used for
      the crypto session.  Allowed values are the ones defined for the
      Prot type field in the SP payload (see Section 6.10 of [RFC3830]).

   *  S (1 bit): flag that MAY be used by the Session Data.

   *  #P (7 bits): indicates the number of security policies provided
      for the crypto session.  In response messages, #P SHALL always be
      exactly 1.  So if #P = 0 in an initial message, a security profile
      MUST be provided in the response message.  If #P > 0, one of the
      suggested policies SHOULD be chosen in the response message.  If
      needed (e.g., in group communication, see Section 9), the
      suggested policies MAY be changed.

   *  Ps (variable length): lists the policies for the crypto session.
      It SHALL contain exactly #P policies, each having the specified
      Prot type.

       0                   1                   2                   3
       0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      !  Policy_no_1  !  Policy_no_2  !      ...      ! Policy_no_#P  !
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+





Mattsson & Tian               Informational                    [Page 33]


RFC 6043                      MIKEY-TICKET                    March 2011


      *  Policy_no_i (8 bits): a policy_no that corresponds to the
         policy_no of a SP payload.  In response messages, the policy_no
         may refer to a SP payload in the initial message.

   *  Session Data Length (16 bits): the length of Session Data (in
      bytes).  For the Prot type SRTP, Session Data MAY be omitted in
      the initial message (length = 0), but it MUST be provided in the
      response message.

   *  Session Data (variable length): contains session data for the
      crypto session.  The type of Session Data depends on the specified
      Prot type.  The Session Data for the Prot type SRTP is defined
      below.  The S flag is used to indicate whether the ROC and SEQ
      fields are provided ('1') or if they are omitted ('0').

       0                   1                   2                   3
       0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      !                              SSRC                             !
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      !                        ROC (OPTIONAL)                         !
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      !         SEQ (OPTIONAL)          !
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

      *  SSRC (32 bits): specifies the SSRC that MUST be used for the
         crypto session.  Note that unlike [RFC3830], an SSRC field set
         to '0' has no special meaning.

      *  ROC (32 bits): current/initial rollover counter.  If the
         session has not started, this field is set to '0'.

      *  SEQ (16 bits): current/initial sequence number.

   *  SPI Length (8 bits): the length of SPI (in bytes).  SPI MAY be
      omitted in the initial message (length = 0), but it MUST be
      provided in the response message.

   *  SPI (variable length): the SPI (or MKI) corresponding to the
      session key to (initially) be used for the crypto session.  This
      does not exclude other keys to be used.  All keys MUST belong to
      the crypto session bundle.

6.2.  Key Data Transport Payload (KEMAC)

   For the KEMAC payload, new encryption and authentication algorithms
   are defined.




Mattsson & Tian               Informational                    [Page 34]


RFC 6043                      MIKEY-TICKET                    March 2011


   *  Encr alg (8 bits): the encryption algorithm used to encrypt the
      Encr data field.  Besides the algorithms already defined in
      [RFC3830], the following additional encryption algorithm may be
      used.

              Encr alg   | Value | Comment
              -----------+-------+---------------------------
              AES-CM-256 |     3 | AES-CM using a 256-bit key

                      Table 6.5: Encr alg (Additions)

   The new encryption algorithm is defined as described in Section 4.2.3
   of [RFC3830] with the only difference being that a 256-bit key SHALL
   be used.

   *  MAC alg (8 bits): specifies the authentication algorithm used.
      Besides the algorithms already defined in [RFC3830], the following
      additional authentication algorithm may be used.

                    MAC alg          | Value | Length
                    -----------------+-------+---------
                    HMAC-SHA-256-256 |     2 | 256 bits

                       Table 6.6: MAC alg (Additions)

   The new authentication algorithm is Hash-based Message Authentication
   Code (HMAC) [RFC2104] in conjunction with SHA-256 [FIPS.180-3].  It
   SHALL be used with a 256-bit authentication key.

6.2.1.  Key Data Sub-Payload

   For the key data sub-payload, new types of keys are defined.  The
   Group TGK (GTGK) is used as a regular TGK, with the difference that
   it SHALL NOT be forked.  It is intended to enable the establishment
   of a group TGK when key forking is used.  The MIKEY Protection Key
   (MPK) is used to protect the MIKEY messages in the Ticket Transfer
   exchange.  The MPK is used as the pre-shared key in the pre-shared
   key method of [RFC3830]; however, it is not known by the Responder
   before the ticket has been resolved.

   An SPI (or MKI) MUST be specified for each key (see Section 6.13 of
   [RFC3830]).

   *  Type (4 bits): indicates the type of key included in the payload.







Mattsson & Tian               Informational                    [Page 35]


RFC 6043                      MIKEY-TICKET                    March 2011


                  Type      | Value | Comments
                  ----------+-------+---------------------
                  GTGK      |     4 | Group TGK
                  GTGK+SALT |     5 | Group TGK + SALT
                  MPK       |     6 | MIKEY Protection Key

                    Table 6.7: Key Data Type (Additions)

6.3.  Timestamp Payload (T)

   For the timestamp payload, a new type of timestamp is defined.  The
   new type is intended to be used when defining validity periods, where
   fractions of seconds seldom matter.  The NTP-UTC-32 string contains
   four bytes, in the same format as the first four bytes in the NTP
   timestamp format, defined in [RFC4330].  This represents the number
   of seconds since 0h on 1 January 1900 with respect to the Coordinated
   Universal Time (UTC).  On 7 February 2036, the time value will
   overflow.  [RFC4330] describes a procedure to extend the time to 2104
   and this procedure is MANDATORY to support.

   *  TS Type (8 bits): specifies the timestamp type used.

                        TS Type    | Value | Length
                        -----------+-------+--------
                        NTP-UTC-32 |     3 | 32 bits

                       Table 6.8: TS Type (Additions)

   NTP-UTC-32 SHALL be padded to a 64-bit NTP-UTC timestamp (with zeroes
   in the fractional second part) when a 64-bit timestamp is required
   (e.g.  IV creation in AES-CM-128 and AES-CM-256).

6.4.  Timestamp Payload with Role Indicator (TR)

   The TR payload uses all the fields from the standard timestamp
   payload (T) but expands it with a new field describing the role of
   the timestamp.  Whereas the TS Type describes the type of the TS
   Value, the TS Role describes the meaning of the timestamp itself.
   The TR payload is intended to eliminate ambiguity when a MIKEY
   message contains several timestamp payloads (e.g., in the Ticket
   Policy).

    0                   1                   2                   3
    0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   ! Next Payload  !    TS Role    !    TS Type    !    TS Value   ~
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+




Mattsson & Tian               Informational                    [Page 36]


RFC 6043                      MIKEY-TICKET                    March 2011


   *  TS Role (8 bits): specifies the sort of timestamp.

                   TS Role                        | Value
                   -------------------------------+------
                   Time of issue (TRi)            |     1
                   Start of validity period (TRs) |     2
                   End of validity period (TRe)   |     3
                   Rekeying interval (TRr)        |     4

                             Table 6.9: TS Role

6.5.  ID Payload (ID)

   For the ID payload, a new ID Type byte string is defined.  The byte
   string type is intended to be used when the ID payload is used to
   identify a pre-shared key.  Contrary to the previously defined ID
   Types (URI, Network Access Identifier), the byte string does not have
   any encoding rules.

   *  ID Type (8 bits): specifies the identifier type used.

                            ID Type     | Value
                            ------------+------
                            Byte string |     2

                      Table 6.10: ID Type (Additions)

6.6.  ID Payload with Role Indicator (IDR)

   The IDR payload uses all the fields from the standard identity
   payload (ID) but expands it with a new field describing the role of
   the ID payload.  Whereas the ID Type describes the type of the ID
   Data, the ID Role describes the meaning of the identity itself.  The
   IDR payload is intended to eliminate ambiguity when a MIKEY message
   contains several identity payloads.  The IDR payload MUST be used
   instead of the ID payload in all MIKEY-TICKET messages.

    0                   1                   2                   3
    0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   ! Next Payload  !    ID Role    !    ID Type    !     ID len
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
     ID len (cont) !                    ID Data                    ~
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+







Mattsson & Tian               Informational                    [Page 37]


RFC 6043                      MIKEY-TICKET                    March 2011


   *  ID Role (8 bits): specifies the sort of identity.

                      ID Role                 | Value
                      ------------------------+------
                      Initiator (IDRi)        |     1
                      Responder (IDRr)        |     2
                      KMS (IDRkms)            |     3
                      Pre-Shared Key (IDRpsk) |     4
                      Application (IDRapp)    |     5

                            Table 6.11: ID Role

   IDRapp is intended to specify the authorized Application IDs (see
   Sections 5.1.3 and 6.10)

6.7.  Cert Hash Payload (CHASH)

   *  Hash func (8 bits): indicates the hash function that is used.
      Besides the hash functions already defined in [RFC3830], the
      following hash function may be used.

                      Hash func | Value | Hash Length
                      ----------+-------+------------
                      SHA-256   |     2 |    256 bits

                     Table 6.12: Hash func (Additions)

   The SHA-256 hash function is defined in [FIPS.180-3].

6.8.  RAND Payload with Role Indicator (RANDR)

   The RANDR payload uses all the fields from the standard RAND payload
   (RAND) but expands it with a new field describing the role (the
   generating entity) of the RAND.  The RANDR payload is intended to
   eliminate ambiguity when a MIKEY message contains several RAND
   payloads.

    0                   1                   2                   3
    0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   ! Next Payload  !    RAND Role  !  RAND length  !     RAND      ~
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

   *  RAND Role (8 bits): specifies the entity that generated the RAND.







Mattsson & Tian               Informational                    [Page 38]


RFC 6043                      MIKEY-TICKET                    March 2011


                         RAND Role          | Value
                         -------------------+------
                         Initiator (RANDRi) |     1
                         Responder (RANDRr) |     2
                         KMS (RANDRkms)     |     3

                           Table 6.13: RAND Role

6.9.  Error Payload (ERR)

   For the key data sub-payload, new types of errors are defined.

   *  Error no (8 bits): indicates the type of error that was
      encountered.

            Error no       | Value | Comments
            ---------------+-------+----------------------------
            Invalid TICKET |    14 | Ticket Type not supported
            Invalid TPpar  |    15 | TP parameters not supported

                      Table 6.14: Error no (Additions)

6.10.  Ticket Policy Payload (TP) / Ticket Payload (TICKET)

   Note that the Ticket Policy payload (TP) and the Ticket Payload
   (TICKET) are two different payloads (having different payload
   identifiers).  However, as they share much of the payload structure,
   they are described in the same section.

   The Ticket Policy payload contains a desired Ticket Policy and does
   not include the Ticket Data length, Ticket Data, Initiator Data
   length, or Initiator Data fields.  The ticket payload contains the
   granted Ticket Policy as well as Ticket Data (the default ticket type
   is defined in Appendix A).  The Ticket Policy contains information
   intended for all parties involved whereas the Ticket Data is only
   intended for the party that resolves the ticket.  The Ticket Type
   provided in the Ticket Data is indicated in the Ticket Policy.  When
   key forking is used (I flag), the Initiator Data authenticates the
   Initiator.

   Note that the flags are not independent: NOT D implies L, G implies
   F, NOT G implies H, NOT H implies G, I implies E, K implies D, and M
   implies F.  The F flag SHALL be set to '1' when the I flag (key
   forking) is set to '1' and a TGK is encoded in the ticket.







Mattsson & Tian               Informational                    [Page 39]


RFC 6043                      MIKEY-TICKET                    March 2011


    0                   1                   2                   3
    0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   ! Next Payload  !          Ticket Type          !    Subtype    !
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   !    Version    !   PRF Func  !D!E!F!G!H!I!J!K!L!M!N!O!   Res   !
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   !        TP Data length         !            TP Data            ~
   +=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+=+
   !      Ticket Data length       !          Ticket Data          ~
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   !     Initiator Data length     !   Initiator Data (OPTIONAL)   ~
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

   *  Next Payload (8 bits): identifies the payload that is added after
      this payload.

   *  Ticket Type (16 bits): specifies the Ticket Type used.

           Ticket Type       | Value | Comments
           ------------------+-------+---------------------------
           MIKEY Base Ticket |     1 | Defined in Appendix A
           3GPP Base Ticket  |     2 | Used and specified by 3GPP

                          Table 6.15: Ticket Type

   Subtype = 0x01 and Version = 0x01 refers to MIKEY Base Ticket as
   defined in this document.

   *  Subtype (8 bits): specifies the ticket subtype used.

   *  Version (8 bits): specifies the ticket subtype version used.

   *  PRF Func (7 bits): specifies the PRF that SHALL be used for key
      forking.

   *  D (1 bit): flag to indicate whether the ticket was generated by
      the KMS ('1') or by the Initiator ('0').

   *  E (1 bit): flag to indicate whether the Ticket Resolve exchange is
      MANDATORY ('1') or if the Responder MAY resolve the ticket ('0').

   *  F (1 bit): flag to indicate whether the TRANSFER_RESP message
      SHALL be sent ('1') or if it SHALL NOT be sent ('0').







Mattsson & Tian               Informational                    [Page 40]


RFC 6043                      MIKEY-TICKET                    March 2011


   *  G (1 bit): flag to indicate whether the Responder SHALL generate
      RANDRr ('1') or if the Responder SHALL NOT generate RANDRr ('0').

   *  H (1 bit): flag to indicate whether RANDRi SHALL be used when
      deriving keys from a TGK/GTGK ('1') or if RANDRi SHALL NOT be used
      ('0').

   *  I (1 bit): flag to indicate whether key forking SHALL be used
      ('1') or if key forking SHALL NOT be used ('0').

   *  J (1 bit): flag to indicate whether the ticket MAY be reused ('1')
      and therefore MAY be cached or if it SHALL NOT be reused ('0').

   *  K (1 bit): flag to indicate whether the KMS changed the desired
      Ticket Policy or the desired KEMAC ('1') or if it did not ('0').
      In the TP payload, it SHALL be set to '0' by the Initiator and
      ignored by the KMS.

   *  L (1 bit): flag to indicate whether the Initiator MAY supply
      session keys ('1') or if the Initiator SHALL NOT supply session
      keys ('0').

   *  M (1 bit): flag to indicate whether the Responder MAY supply
      session keys ('1') or if the Responder SHALL NOT supply session
      keys ('0').

   *  N (1 bit): flag to indicate whether an Initiator following this
      specification can initiate a TRANSFER_INIT message using the
      ticket ('1') or if additional processing is required ('0').  If
      the flag is set to '0', the Initiator SHOULD follow the processing
      in the specification of the received Ticket Type.

   *  O (1 bit): flag to indicate whether a Responder following this
      specification can process a TRANSFER_INIT message containing the
      ticket ('1') or if additional processing is required ('0').  If
      the flag is set to '0', the Responder SHOULD follow the processing
      in the specification of the received Ticket Type.

   *  Res (5 bits): reserved for future use.

   *  TP Data length (16 bits): length of TP Data (in bytes).

   *  TP Data (variable length): The first 8 bits identify the first
      payload.  The rest of TP Data SHALL be constructed of MIKEY
      payloads.  Unexpected payloads in the TP Data SHOULD be ignored.

             TP Data = First Payload, [IDRkms], [IDRi], [TRs],
                       [TRe], [TRr], [KEMAC], {IDRapp}, (IDRr)



Mattsson & Tian               Informational                    [Page 41]


RFC 6043                      MIKEY-TICKET                    March 2011


      IDRkms contains the identity of a KMS that can resolve the ticket.

      IDRi contains the identity of the peer that requested or created
      the ticket.

      TRs is the start of the validity period.  TRs SHALL be interpreted
      as being in the range 1968-2104 as described in [RFC4330].  An
      omitted TRs means that the validity period has no defined
      beginning.

      TRe is the end of the validity period.  TRe SHALL be interpreted
      as being in the range 1968-2104 as described in [RFC4330].  An
      omitted TRe means that the validity period has no defined end.

      TRr indicates how often rekeying MUST be done.  TS Type SHALL be
      NTP-UTC-32 and the time between two rekeyings SHALL NOT be longer
      than the number of seconds in the integer part of the timestamp.
      How the rekeying is done is implementation specific.

      The KEMAC payload may be used to indicate the number of requested
      keys and specify other key information (key type, key length, and
      KV (key validity) data).  The KEMAC payload SHALL use the NULL
      encryption algorithm and the NULL authentication algorithm, as a
      MAC is included in the V payload.  The KEMAC is hence constructed
      as follows:

                           KEMAC = {TEK|TGK|GTGK}

   The Key Data fields SHALL be set to '0' by the Initiator and ignored
   by the KMS.  The KEMAC SHALL NOT be present in the granted Ticket
   Policy.

      IDRapp is an identifier for an authorized application ID.  The
      application IDs are implementation specific.  If no IDRapp
      payloads are supplied, all application IDs are authorized.

      IDRr is the identity of a responder or a group of responders that
      are authorized to resolve the ticket.  If there is more than one
      responder identity, each responder identity SHALL be included in a
      separate IDR payload.

   *  Ticket Data length (16 bits): the length of the Ticket Data field
      (in bytes).  Not present in the TP payload.

   *  Ticket Data (variable length): contains the Ticket Data.  Not
      present in the TP payload.





Mattsson & Tian               Informational                    [Page 42]


RFC 6043                      MIKEY-TICKET                    March 2011


   *  Initiator Data length (16 bits): the length of the Initiator Data
      field (in bytes).  Not present in the TP payload.

   *  Initiator Data (variable length): Not present in the TP payload.
      SHALL be inserted by the Initiator if and only if key forking is
      used (I flag).  The first 8 bits identifies the first payload.
      The rest of Initiator Data SHALL be constructed of MIKEY payloads.
      Unexpected payloads in the Initiator Data SHOULD be ignored.

                   Initiator Data = First Payload, Vi, Vr

      The Vi payload SHALL be identical to the V payload in the
      TRANSFER_INIT message.

      The last payload (Vr) SHALL be a Verification payload where the
      MAC SHALL cover the entire Initiator Data field except the MAC
      field itself.  The authentication algorithm SHALL be the same as
      used for the Vi payload.  The authentication key (auth_key) SHALL
      be derived from MPKr (not forked) using the following parameters:

      inkey:     : MPKr
      inkey_len  : bit length of the inkey
      label      : constant || 0xFF || 0xFFFFFFFF || 0x04
      outkey_len : desired bit length of the outkey (encr_key,
                   auth_key, salt_key)

      The constant depends on the derived key type as defined in Section
      4.1.4 of [RFC3830].

7.  Transport Protocols

   MIKEY messages are not tied to any specific transport protocols.  In
   [RFC4567], extensions for SDP and RTSP to carry MIKEY messages (and
   therefore MIKEY-TICKET messages) are defined.  The messages in the
   Ticket Transfer exchange (TRANSFER_INIT, TRANSFER_RESP) are
   preferably included in the session setup signaling (e.g., SIP INVITE
   and 200 OK).  However, it may not be suitable for the MIKEY-TICKET
   exchanges that do not establish keying material for media sessions
   (Ticket Request and Ticket Resolve) to be carried in SDP or RTSP.  If
   SDP or RTSP is not used, the transport protocol needs to be defined.
   In [3GPP.33.328], it is defined how the Ticket Request and Ticket
   Resolve exchanges are carried over HTTP.

8.  Pre-Encrypted Content

   The default setting is that the KMS supplies the session keys
   (encoded in the ticket).  This is not possible if the content is pre-
   encrypted (e.g., Video on Demand).  In such use cases, the key



Mattsson & Tian               Informational                    [Page 43]


RFC 6043                      MIKEY-TICKET                    March 2011


   exchange is typically reversed and MAY be carried out as follows.
   The Initiator sends a ticket without encoded session keys to the
   Responder in a TRANSFER_INIT message.  The Responder has access to
   the TEKs used to protect the requested content, but may not be
   streaming the content.  The Responder includes the TEK in the
   TRANSFER_RESP message, which is sent to the Initiator.

   +---+                                                           +---+
   | I |                                                           | R |
   +---+                                                           +---+
                               TRANSFER_INIT
     ---------------------------------------------------------------->
                               TRANSFER_RESP {KEMAC}
     <----------------------------------------------------------------

              Figure 6: Distribution of pre-encrypted content

9.  Group Communication

   What has been discussed up to now can also be used for group
   communication.  The MIKEY signaling for multi-party sessions can be
   centralized as illustrated in Figure 7.

   +---+                           +---+                           +---+
   | A |                           | B |                           | C |
   +---+                           +---+                           +---+
              Ticket Transfer
     <------------------------------->        Ticket Transfer
     <--------------------------------------------------------------->

              Figure 7: Centralized signaling around party A

   or decentralized as illustrated in Figure 8.

   +---+                           +---+                           +---+
   | A |                           | B |                           | C |
   +---+                           +---+                           +---+
              Ticket Transfer
     <------------------------------->        Ticket Transfer
                                     <------------------------------->

                     Figure 8: Decentralized signaling

   In the decentralized scenario, the identities of B and C SHALL be
   used in the second Ticket Transfer exchange.  Independent of the how
   the MIKEY signaling is done, a group key may be used as session key.





Mattsson & Tian               Informational                    [Page 44]


RFC 6043                      MIKEY-TICKET                    March 2011


   If a group key is used, the group key and session information may be
   pushed to all group members (similar to [RFC3830]), or distributed
   when requested (similar to [RFC4738]).  If a TGK/GTGK is used as a
   group key, the same RANDs MUST be used to derive the session keys in
   all Ticket Transfer exchanges.  Also note caveats with ticket reuse
   in group communication settings as discussed in Section 5.3.

9.1.  Key Forking

   When key forking is used, only the user that requested the ticket can
   initiate a Ticket Transfer exchange using that ticket, see
   Section 5.3.  So if a group key is to be distributed, the MIKEY
   signaling MUST be centralized to the party that initially requested
   the ticket, or different tickets needs to be used in each Ticket
   Transfer exchange and the group key needs to be sent in a KEMAC.

   Another consideration is that different users get different session
   keys if TGKs (encoded in the ticket) are used.

10.  Signaling between Different KMSs

   A user can in general only be expected to have a trust relation with
   a single KMS.  Different users might therefore use tickets issued by
   different KMSs using only locally known keys.  Thus, if users with
   trust relations to different KMSs are to be able to establish a
   secure session with each other, the KMSs involved have to cooperate
   and there has to be a trust relation between them.  The KMSs SHALL be
   mutually authenticated and signaling between them SHALL be integrity
   and confidentiality protected.  The technical means for the inter-KMS
   security is however outside the scope of this specification.  Under
   these assumptions, the following approach MAY be used.

   +---+               +---+              +-------+            +-------+
   | I |               | R |              | KMS R |            | KMS I |
   +---+               +---+              +-------+            +-------+
         TRANSFER_INIT
     -------------------->    RESOLVE_INIT
                         - - - - - - - - - - ->    RESOLVE_INIT
                                              - - - - - - - - - - ->
                                                   RESOLVE_RESP
                              RESOLVE_RESP    <- - - - - - - - - - -
         TRANSFER_RESP   < - - - - - - -  - - -
     <--------------------

                   Figure 9: Routing of resolve messages






Mattsson & Tian               Informational                    [Page 45]


RFC 6043                      MIKEY-TICKET                    March 2011


   If the Responder cannot directly resolve a ticket, the ticket SHOULD
   be included in a RESOLVE_INIT message sent to a KMS.  If the
   Responder does not have a shared credential with the KMS that issued
   the ticket (KMS I) or if the Responder does not know which KMS issued
   the ticket, the Responder SHOULD send the RESOLVE_INIT message to one
   of the Responder's trusted KMSs (KMS R).  If KMS R did not issue the
   ticket, KMS R would normally be unable to directly resolve the ticket
   and must hence ask another KMS to resolve it (typically the issuing
   KMS).

   The signaling between different KMSs MAY be done with a Ticket
   Resolve exchange as illustrated in Figure 9.  The IDRr and TICKET
   payloads from the previous RESOLVE_INIT message SHOULD be reused.
   Note that IDRr cannot be used to look up the pre-shared key/
   certificate.

11.  Adding New Ticket Types to MIKEY-TICKET

   The Ticket Data (in the TICKET payload) could be a reference to
   information (keys, etc.) stored by the key management service, it
   could contain all the information itself, or it could be a
   combination of the two alternatives.  For systems serving many users,
   it is not ideal to use the reference-only ticket approach as this
   would force the key management service to keep state of all issued
   tickets that are still valid.  Tickets may carry many different types
   of information helping to enforce usage policies.  The policies may
   be group policies or per-user policies.

   Tickets may either be transparent, meaning they can be resolved
   without contacting the KMS that generated them, or opaque, meaning
   that the original KMS must be contacted.  The ticket information
   SHOULD typically be integrity protected and certain fields need
   confidentiality protection, in particular, the keys if explicitly
   included.  Other types of information may also require
   confidentiality protection due to privacy reasons.  In mode 2 (see
   Section 4.1.1), it may be preferable to include several encrypted
   ticket protection keys (similar to Secure/Multipurpose Internet Mail
   Extensions (S/MIME)) as this may allow multiple peers to resolve the
   ticket.

   The Ticket Data MUST include information so that the resolving party
   can retrieve an encoded KEMAC.  It MUST also be possible to verify
   the integrity of the TICKET payload.  It is RECOMMENDED that future
   specifications use the recommended payload order and do not add any
   additional payloads or processing.  New Ticket Types SHOULD NOT
   change the processing for the Responder.  If a new Ticket Type





Mattsson & Tian               Informational                    [Page 46]


RFC 6043                      MIKEY-TICKET                    March 2011


   requires additional processing, it MUST be indicated in the Ticket
   Policy (N and O flags).  New specifications MUST specify which modes
   are supported and if any additional security considerations apply.

12.  Security Considerations

   Unless otherwise stated, the security considerations in [RFC3830]
   still apply and contain notes on the security properties of the MIKEY
   protocol, key derivation functions, and other components.  As some
   security properties depend on the specific Ticket Type, only generic
   security considerations concerning the MIKEY-TICKET framework are
   discussed.

   This specification includes a large number of optional features,
   which adds complexity to the general case.  Protocol designers are
   strongly encouraged to establish strict profiles defining MIKEY-
   TICKET options (e.g., exchanges or message fields) that SHOULD or
   MUST be supported.  Such profiles should preclude unexpected
   consequences from compliant implementations with wildly differing
   option sets.

12.1.  General

   In addition to the Ticket Policy, the KMS MAY have its own set of
   policies (authorized key lengths, algorithms, etc.) that in some way
   are shared with the peers.  The KMS MAY also provide keying material
   to authorized intermediate nodes performing various network functions
   (e.g., transcoding services, recording services, conference bridges).
   The key management service can enforce end-to-end security by only
   distributing the keys to authorized end-users.  As in [RFC3830], the
   user identities are not confidentiality protected.  If user privacy
   is needed, some kind of Privacy Enhancing Technologies (PET) like
   anonymous or temporary credentials MAY be used.

   In the standard MIKEY modes [RFC3830], the keys are generated by the
   Initiator (or by both peers in the Diffie-Hellman scheme).  If a bad
   PRNG (Pseudorandom Number Generator) is used, this is likely to make
   any key management protocol sensitive to different kinds of attacks,
   and MIKEY is no exception.  As the choice of the PRNG is
   implementation specific, the easiest (and often bad) choice is to use
   the PRNG supplied by the operating system.  In MIKEY-TICKET's default
   mode of operation, the key generation is mostly done by the KMS,
   which can be assumed to be less likely to use a bad random number
   generator.  All keys (including keys used to protect the ticket) MUST
   have adequate strength/length, i.e., 128 bits or more.






Mattsson & Tian               Informational                    [Page 47]


RFC 6043                      MIKEY-TICKET                    March 2011


   The use of random nonces (RANDs) in the key derivation is of utmost
   importance to counter offline pre-computation attacks and other
   generic attacks.  A key of length n, using RANDs of length r, has
   effective key entropy of (n + r) / 2 against a birthday attack.
   Therefore, the sum of the lengths of RANDRi and RANDRr MUST at least
   be equal to the size of the longest pre-shared key/envelope key/MPK/
   TGK/GTGK, RANDRkms MUST at least be as long as the longest MPKr/TGK,
   and the RAND in the MIKEY base ticket MUST at least be as long as the
   longest of TPK and MPK.

   Note that the CSB Updating messages reuse the old RANDs.  This means
   that the total effective key entropy (relative to pre-computation
   attacks) for k consecutive key updates, assuming the TGKs are each n
   bits long, is still no more than n bits.  In other words, the time
   and memory needed by an attacker to get all k n-bit keys are
   proportional to 2^n.  While this might seem like a defect, this is in
   practice (for all reasonable values of k) not better than brute
   force, which on average requires k * 2^(n-1) work (even if different
   RANDs would be used).  A birthday attack would only require 2^(n/2)
   work, but would need access to 2^(n/2) sessions protected with
   equally many different keys using a single pair of RANDs.  This is,
   for typical values of n, clearly totally infeasible.  The success
   probability of such an attack can be controlled by limiting the
   number of updates correspondingly.  As stated in [RFC3830], the fact
   that more than one key can be compromised in a single attack is
   inherent to any solution using secret- or public-key algorithms.  An
   attacker always gets access to all the exchanged keys by doing an
   exhaustive search on the pre-shared key/envelope key/MPK.  This
   requires 2^m work, where m is the effective size of the key.

   As the Responder MAY generate a RAND, the Ticket Transfer exchange
   can provide mutual freshness guarantee for all derived keys.

   The new algorithms PRF-HMAC-SHA-256, AES-CM-256, and HMAC-SHA-256-256
   use 256-bit keys and offer a higher security level than the
   previously defined algorithms.  If one of the 256-bit algorithms are
   supported, the other two algorithms SHALL also be supported.  The
   256-bit algorithms SHOULD be used together, and they SHALL NOT be
   mixed with algorithms using key sizes less than 256 bits.  If session
   keys (TEK/TGK/GTGK) longer than 128 bits are used, 128-bit algorithms
   SHALL NOT be used.

12.2.  Key Forking

   In some situations, the TRANSFER_INIT message may be delivered to
   multiple endpoints.  For example, when a Responder is registered on
   several devices (e.g., mobile phone, fixed phone, and computer) or
   when an invite is being made to addresses of the type



Mattsson & Tian               Informational                    [Page 48]


RFC 6043                      MIKEY-TICKET                    March 2011


   IT-support@example.com, a group of users where only one is supposed
   to answer.  The Initiator may not even always know exactly who the
   authorized group members are.  To prevent all forms of eavesdropping,
   entities other than the endpoint that answers MUST NOT get access to
   the session keys.

   When key forking is not used, keys are accessible by everyone that
   can resolve the ticket.  When key forking is used, some keys (MPKr
   and TGKs encoded in the ticket) are modified, making them
   cryptographically unique for each responder targeted by the forking.
   As only the Initiator and the KMS have access to the master TGKs, it
   is infeasible for anyone else to derive the session keys.

   When key forking is used, some keys (MPKi and TEKs and GTGK encoded
   in the ticket) are still accessible by everyone that can resolve the
   ticket and should be used with this in mind.  This also concerns
   session keys transferred in a KEMAC in the first TRANSFER_INIT (as
   they are protected with MPKi).

12.3.  Denial of Service

   This protocol is resistant to denial-of-service attacks against the
   KMS in the sense that it does not construct any state (at the key
   management protocol level) before it has authenticated the Initiator
   or Responder.  Since the Responder, in general, cannot verify the
   validity of a TRANSFER_INIT message without first contacting the KMS,
   denial of service may be launched against the Responder and/or the
   KMS via the Responder.  Typical prevention methods such as rate-
   limiting and ACL (Access Control List) capability SHOULD therefore be
   implemented in the KMS as well as the clients.  If something in the
   signaling is suspicious, the Responder SHOULD abort before attempting
   a RESOLVE_INIT with the KMS.  The types and amount of prevention
   needed depends on how critical the system is and may vary depending
   on the Ticket Type.

12.4.  Replay

   In a replay attack, an attacker may intercept and later retransmit
   the whole or part of a MIKEY message, attempting to trick the
   receiver (Responder or KMS) into undesired operations, e.g., leading
   to a lack of key freshness.  MIKEY-TICKET implements several
   mechanisms to prevent and detect such attacks.  Timestamps together
   with a replay cache efficiently stop the replay of entire MIKEY
   messages.  Parts of the received messages (or their hashes) can be
   saved in the replay cache until their timestamp is outdated.  To
   prevent replay attacks, the sender's (Initiator or Responder) and the
   receiver's (Responder or KMS) identity is always (explicitly or
   implicitly) included in the MAC/Signature calculation.



Mattsson & Tian               Informational                    [Page 49]


RFC 6043                      MIKEY-TICKET                    March 2011


   An attacker may also attempt to replay a ticket by inserting it into
   a new MIKEY message.  A possible scenario is that Alice and Bob first
   communicate based on a ticket, which an attacker Mallory intercepts.
   Later, Mallory (acting as herself) invites Bob by inserting the
   ticket into her own TRANSFER_INIT message.  If key forking is used,
   such replays will always be detected when Bob has resolved the
   ticket.  If key forking is not used, such replays will be detected
   unless Mallory has knowledge of the MPKi.  And if Mallory has
   knowledge of the MPKi (i.e., she is authorized to resolve the ticket)
   and key forking is not used, there is no attack.  For the reasons
   explained above, it is RECOMMENDED to use key forking.

12.5.  Group Key Management

   In a group scenario, only authorized group members must have access
   to the keys.  In some situation, the communication may be initiated
   by the Initiator using a group identity and the Initiator may not
   even know exactly who the authorized group members are.  Moreover,
   group membership may change over time due to leaves/joins.  In such a
   situation, it is foremost the responsibility of the KMS to reject
   ticket resolution requests from unauthorized responders, implying
   that the KMS needs to be able to map an individual's identity
   (carried in the RESOLVE_INIT message) to group membership (where the
   group identity is carried in the ticket).

   As noted, reuse of tickets, which bypasses the KMS, is NOT
   RECOMMENDED when the Initiator is not fully ensured about group
   membership status.

13.  Acknowledgements

   The authors would like to thank Fredrik Ahlqvist, Rolf Blom, Yi
   Cheng, Lakshminath Dondeti, Vesa Lehtovirta, Fredrik Lindholm, Mats
   Naslund, Karl Norrman, Oscar Ohlsson, Brian Rosenberg, Bengt Sahlin,
   Wei Yinxing, and Zhu Yunwen for their support and valuable comments.

14.  IANA Considerations

   This document defines several new values for the namespaces Data
   Type, Next Payload, PRF func, CS ID map type, Encr alg, MAC alg, TS
   Type, ID Type, Hash func, Error no, and Key Data Type defined in
   [RFC3830].  The following IANA assignments were added to the MIKEY
   Payload registry (in parentheses is a reference to the table
   containing the registered values):

   o  Data Type (see Table 6.1)

   o  Next Payload (see Table 6.2)



Mattsson & Tian               Informational                    [Page 50]


RFC 6043                      MIKEY-TICKET                    March 2011


   o  PRF func (see Table 6.3)

   o  CS ID map type (see Table 6.4)

   o  Encr alg (see Table 6.5)

   o  MAC alg (see Table 6.6)

   o  TS Type (see Table 6.7)

   o  ID Type (see Table 6.9)

   o  Hash func (see Table 6.11)

   o  Error no (see Table 6.13)

   o  Key Data Type (see Table 6.14)

   The TR payload defines an 8-bit TS Role field for which IANA has
   created and will maintain a new namespace in the MIKEY Payload
   registry.  Assignments consist of a TS Role name and its associated
   value.  Values in the range 1-239 SHOULD be approved by the process
   of Specification Required, values in the range 240-254 are Reserved
   for Private Use, and the values 0 and 255 are Reserved according to
   [RFC5226].  The initial contents of the registry are as follows:

                  Value    TS Role
                  -------  ------------------------------
                  0        Reserved
                  1        Time of issue (TRi)
                  2        Start of validity period (TRs)
                  3        End of validity period (TRe)
                  4        Rekeying interval (TRr)
                  5-239    Unassigned
                  240-254  Reserved for Private Use
                  255      Reserved

   The IDR payload defines an 8-bit ID Role field for which IANA has
   created and will maintain a new namespace in the MIKEY Payload
   registry.  Assignments consist of an ID Role name and its associated
   value.  Values in the range 1-239 SHOULD be approved by the process
   of Specification Required, values in the range 240-254 are Reserved
   for Private Use, and the values 0 and 255 are Reserved according to
   [RFC5226].  The initial contents of the registry are as follows:







Mattsson & Tian               Informational                    [Page 51]


RFC 6043                      MIKEY-TICKET                    March 2011


                     Value    ID Role
                     -------  -----------------------
                     0        Reserved
                     1        Initiator (IDRi)
                     2        Responder (IDRr)
                     3        KMS (IDRkms)
                     4        Pre-Shared Key (IDRpsk)
                     5        Application (IDRapp)
                     6-239    Unassigned
                     240-254  Reserved for Private Use
                     255      Reserved

   The RANDR payload defines an 8-bit RAND Role field for which IANA has
   created and will maintain a new namespace in the MIKEY Payload
   registry.  Assignments consist of a RAND Role name and its associated
   value.  Values in the range 1-239 SHOULD be approved by the process
   of Specification Required, values in the range 240-254 are Reserved
   for Private Use, and the values 0 and 255 are Reserved according to
   [RFC5226].  The initial contents of the registry are as follows:

                     Value    RAND Role
                     -------  ------------------
                     0        Reserved
                     1        Initiator (RANDRi)
                     2        Responder (RANDRr)
                     3        KMS (RANDRkms)
                     4-239    Unassigned
                     240-254  Reserved for Private Use
                     255      Reserved

   The TP/TICKET payload defines a 16-bit Ticket Type field for which
   IANA has created and will maintain a new namespace in the MIKEY
   Payload registry.  Assignments consist of a Ticket Type name and its
   associated value.  Values in the range 1-61439 SHOULD be approved by
   the process of Specification Required, values in the range 61440-
   65534 are Reserved for Private Use, and the values 0 and 65535 are
   Reserved according to [RFC5226].  The initial contents of the
   registry are as follows:

                   Value        Ticket Type
                   -----------  -----------------
                   0            Reserved
                   1            MIKEY base ticket
                   2            3GPP base ticket
                   3-61439      Unassigned
                   61440-65534  Reserved for Private Use
                   65535        Reserved




Mattsson & Tian               Informational                    [Page 52]


RFC 6043                      MIKEY-TICKET                    March 2011


15.  References

15.1.  Normative References

   [FIPS.180-3]   National Institute of Standards and Technology,
                  "Secure Hash Standard (SHS)", FIPS PUB 180-3,
                  October 2008, <http://csrc.nist.gov/publications/fips/
                  fips180-3/fips180-3_final.pdf>.

   [RFC2104]      Krawczyk, H., Bellare, M., and R. Canetti, "HMAC:
                  Keyed-Hashing for Message Authentication", RFC 2104,
                  February 1997.

   [RFC2119]      Bradner, S., "Key words for use in RFCs to Indicate
                  Requirement Levels", BCP 14, RFC 2119, March 1997.

   [RFC3830]      Arkko, J., Carrara, E., Lindholm, F., Naslund, M., and
                  K. Norrman, "MIKEY: Multimedia Internet KEYing",
                  RFC 3830, August 2004.

   [RFC4330]      Mills, D., "Simple Network Time Protocol (SNTP)
                  Version 4 for IPv4, IPv6 and OSI", RFC 4330,
                  January 2006.

   [RFC4563]      Carrara, E., Lehtovirta, V., and K. Norrman, "The Key
                  ID Information Type for the General Extension Payload
                  in Multimedia Internet KEYing (MIKEY)", RFC 4563,
                  June 2006.

   [RFC4567]      Arkko, J., Lindholm, F., Naslund, M., Norrman, K., and
                  E. Carrara, "Key Management Extensions for Session
                  Description Protocol (SDP) and Real Time Streaming
                  Protocol (RTSP)", RFC 4567, July 2006.

   [RFC4738]      Ignjatic, D., Dondeti, L., Audet, F., and P. Lin,
                  "MIKEY-RSA-R: An Additional Mode of Key Distribution
                  in Multimedia Internet KEYing (MIKEY)", RFC 4738,
                  November 2006.

   [RFC5226]      Narten, T. and H. Alvestrand, "Guidelines for Writing
                  an IANA Considerations Section in RFCs", BCP 26,
                  RFC 5226, May 2008.

15.2.   Informative References

   [3GPP.33.328]  3GPP, "IP Multimedia Subsystem (IMS) media plane
                  security", 3GPP TS 33.328 9.3.0, December 2010.




Mattsson & Tian               Informational                    [Page 53]


RFC 6043                      MIKEY-TICKET                    March 2011


   [Otway-Rees]   Otway, D., and O. Rees, "Efficient and Timely Mutual
                  Authentication", ACM SIGOPS Operating Systems
                  Review v.21 n.1, p.8-10, January 1987.

   [RFC3261]      Rosenberg, J., Schulzrinne, H., Camarillo, G.,
                  Johnston, A., Peterson, J., Sparks, R., Handley, M.,
                  and E. Schooler, "SIP: Session Initiation Protocol",
                  RFC 3261, June 2002.

   [RFC4120]      Neuman, C., Yu, T., Hartman, S., and K. Raeburn, "The
                  Kerberos Network Authentication Service (V5)",
                  RFC 4120, July 2005.

   [RFC4650]      Euchner, M., "HMAC-Authenticated Diffie-Hellman for
                  Multimedia Internet KEYing (MIKEY)", RFC 4650,
                  September 2006.

   [RFC5197]      Fries, S. and D. Ignjatic, "On the Applicability of
                  Various Multimedia Internet KEYing (MIKEY) Modes and
                  Extensions", RFC 5197, June 2008.

   [RFC5479]      Wing, D., Fries, S., Tschofenig, H., and F. Audet,
                  "Requirements and Analysis of Media Security
                  Management Protocols", RFC 5479, April 2009.



























Mattsson & Tian               Informational                    [Page 54]


RFC 6043                      MIKEY-TICKET                    March 2011


Appendix A.  MIKEY Base Ticket

   The MIKEY base ticket MAY be used in any of the modes described in
   Section 4.1.1.  The Ticket Data SHALL be constructed of MIKEY
   payloads and SHALL be protected by a MAC based on a pre-shared Ticket
   Protection Key (TPK).  The parties that shares the TPK depends on the
   mode.  Unexpected payloads in the Ticket Data SHOULD be ignored.

              Ticket Data = THDR, T, RAND, KEMAC, [IDRpsk], V

A.1.  Components of the Ticket Data

   The Ticket Data MUST always begin with a Ticket Header payload
   (THDR).  The ticket header is a new payload type; for the definition,
   see Appendix A.3.

   T is a timestamp containing the time of issue or a counter.  It MAY
   be used in the IV (Initialization Vector) formation (e.g., Section
   4.2.3 of [RFC3830]).

   RAND is used as input to the key derivation function when keys are
   derived from the TPK and the MPK (see Appendices A.2.1 and A.2.2).

   The KEMAC payload SHALL use the NULL authentication algorithm, as a
   MAC is included in the V payload.  The encryption key (encr_key) and
   salting key (salt_key) SHALL be derived from the TPK (see
   Appendix A.2.1).  Depending on the encryption algorithm, the salting
   key be used in the IV creation (see Section 4.2.3 of [RFC3830]).  If
   CSB ID is needed in the IV creation it SHALL be set to '0xFFFFFFFF'.
   The KEMAC is hence constructed as follows:

                 KEMAC = E(encr_key, MPK || {TEK|TGK|GTGK})

   MPKi and MPKr are derived from the MPK as defined in Appendix A.2.2.

   IDRpsk contains an identifier that enables the KMS/Responder to
   retrieve the TPK.  It MAY be omitted when the TPK can be retrieved
   anyhow.

   The last payload SHALL be a Verification payload (V) where the
   authentication key (auth_key) is derived from the TPK.  The MAC SHALL
   be calculated over the entire TICKET payload except the Next Payload
   field (in the TICKET payload), the Initiator Data length field, the
   Initiator Data field, and the MAC field itself.







Mattsson & Tian               Informational                    [Page 55]


RFC 6043                      MIKEY-TICKET                    March 2011


A.2.  Key Derivation

   The labels in the key derivations SHALL NOT include entire RAND
   payloads, only the fields RAND length and RAND from the corresponding
   payload.

A.2.1.  Deriving Keys from a TPK

   In the following, we describe how keying material is derived from a
   TPK.  The key derivation method SHALL be executed using the PRF
   indicated in the Ticket Policy.  The parameters for the PRF are:

   inkey:     : TPK
   inkey_len  : bit length of the inkey
   label      : constant || 0xFF || 0xFFFFFFFF || 0x05 ||
                length RAND || RAND
   outkey_len : desired bit length of the outkey (encr_key,
                auth_key, salt_key)

   Length RAND is the length of RAND in bytes as an 8-bit unsigned
   integer.  The constants are as defined in Section 4.1.4 of [RFC3830].
   The key derivation and its dependencies on Ticket Data contents when
   AES-CM is used are illustrated in Figure 10.  The key derivation is
   done by the party that creates the ticket (KMS or Initiator) and by
   the party that resolves the ticket (KMS or Responder).  The
   encryption key and the IV are used to encrypt the KEMAC.

                                 -----          auth_key        ------
              -----     TPK     |     |----------------------->| AUTH |
             | TPK |----------->|     |       encr_key          ------
              -----             | PRF |--------------------+       |
                ^           +-->|     |     salt_key       |       |
                :           |   |     |----------------+   |       |
                :           |    -----                 |   |       |
                :           |                          v   |       |
       identify :      RAND |            TS value    ----  |       | MAC
                :           |         +------------>| IV | |       |
                :           |         |              ----  |       |
                :           |         |             IV |   |       |
                :           |         |                v   v       v
   Ticket   +---+----+---+--+---+---+-+-+------------+-------+---+---+
    Data    | IDRpsk |...| RAND |...| T |............| KEMAC |...| V |
            +--------+---+------+---+---+------------+-------+---+---+

                    Figure 10: Deriving keys from a TPK






Mattsson & Tian               Informational                    [Page 56]


RFC 6043                      MIKEY-TICKET                    March 2011


A.2.2.  Deriving MPKi and MPKr

   In the following, we describe how MPKi and MPKr are derived from the
   MPK in the KEMAC payload.  The key derivation method SHALL be
   executed using the PRF indicated in the Ticket Policy.  The
   parameters for the PRF are:

   inkey:     : MPK
   inkey_len  : bit length of the inkey
   label      : constant || 0xFF || 0xFFFFFFFF || 0x06 ||
                length RAND || RAND
   outkey_len : desired bit length of the outkey (MPKi, MPKr)
                SHALL be equal to inkey_len

   Length RAND is the length of RAND in bytes as an 8-bit unsigned
   integer.  The constant depends on the derived key type as summarized
   below.

                          Derived key | Constant
                          ------------+-----------
                          MPKi        | 0x220E99A2
                          MPKr        | 0x1F4D675B

                Table A.1: Constants for MPK key derivation

   The constants are taken from the decimal digits of e as described in
   [RFC3830].

A.3.  Ticket Header Payload (THDR)

   The ticket header payload contains an indicator of the next payload
   as well as implementation-specific data.

    0                   1                   2                   3
    0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   ! Next Payload  !        THDR Data length       !   THDR Data   ~
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

   *  Next Payload (8 bits): identifies the payload that is added after
      this payload.

   *  THDR Data length (16 bits): the length of the THDR Data field (in
      bytes).

   *  THDR Data (variable length): implementation specific data that
      SHOULD be ignored if it is not expected.




Mattsson & Tian               Informational                    [Page 57]


RFC 6043                      MIKEY-TICKET                    March 2011


Appendix B.  Alternative Use Cases

B.1.  Compatibility Mode

   MIKEY-TICKET can be used to define a Ticket Type compatible with
   [RFC3830] or any other half-round-trip key management protocol.  The
   Initiator requests and gets a ticket from the KMS where the Ticket
   Data is a [RFC3830] message protected with a pre-shared key
   (KMS-Responder) or with the Responder's certificate.  The Ticket Data
   is then sent to the Responder according to [RFC3830].  In this way,
   the Initiator can communicate with a Responder that only supports
   [RFC3830] and with whom the Initiator do not have any shared
   credentials.

   +---+                          +-----+                          +---+
   | I |                          | KMS |                          | R |
   +---+                          +-----+                          +---+
               REQUEST_INIT
     -------------------------------->
               REQUEST_RESP
     <--------------------------------
                                3830 MIKEY
     ---------------------------------------------------------------->

                       Figure 11: Compatibility mode

Authors' Addresses

   John Mattsson
   Ericsson AB
   SE-164 80 Stockholm
   Sweden

   Phone: +46 10 71 43 501
   EMail: john.mattsson@ericsson.com


   Tian Tian
   ZTE Corporation
   4F, RD Building 2, Zijinghua Road
   Yuhuatai District, Nanjing 210012
   P.R. China

   Phone: +86-025-5287-7867
   EMail: tian.tian1@zte.com.cn






Mattsson & Tian               Informational                    [Page 58]

mirror server hosted at Truenetwork, Russian Federation.