4.2. The Storage Spectrum

4.2.1. CPU Registers

Every present-day CPU design includes registers for a variety of purposes, from storing the address of the currently-executed instruction to more general-purpose data storage and manipulation. CPU registers run at the same speed as the rest of the CPU; otherwise, they would be a serious bottleneck to overall system performance. The reason for this is that nearly all operations performed by the CPU involve the registers in one way or another.

The number of CPU registers (and their uses) are strictly dependent on the architectural design of the CPU itself. There is no way to change the number of CPU registers, short of migrating to a CPU with a different architecture. For these reasons, the number of CPU registers can be considered a constant, as they are changeable only with great pain and expense.

4.2.2. Cache Memory

The purpose of cache memory is to act as a buffer between the very limited, very high-speed CPU registers and the relatively slower and much larger main system memory — usually referred to as RAM[1]. Cache memory has an operating speed similar to the CPU itself so, when the CPU accesses data in cache, the CPU is not kept waiting for the data.

Cache memory is configured such that, whenever data is to be read from RAM, the system hardware first checks to determine if the desired data is in cache. If the data is in cache, it is quickly retrieved, and used by the CPU. However, if the data is not in cache, the data is read from RAM and, while being transferred to the CPU, is also placed in cache (in case it is needed again later). From the perspective of the CPU, all this is done transparently, so that the only difference between accessing data in cache and accessing data in RAM is the amount of time it takes for the data to be returned.

In terms of storage capacity, cache is much smaller than RAM. Therefore, not every byte in RAM can have its own unique location in cache. As such, it is necessary to split cache up into sections that can be used to cache different areas of RAM, and to have a mechanism that allows each area of cache to cache different areas of RAM at different times. Even with the difference in size between cache and RAM, given the sequential and localized nature of storage access, a small amount of cache can effectively speed access to a large amount of RAM.

When writing data from the CPU, things get a bit more complicated. There are two different approaches that can be used. In both cases, the data is first written to cache. However, since the purpose of cache is to function as a very fast copy of the contents of selected portions of RAM, any time a piece of data changes its value, that new value must be written to both cache memory and RAM. Otherwise, the data in cache and the data in RAM would no longer match.

The two approaches differ in how this is done. One approach, known as write-through caching, immediately writes the modified data to RAM. Write-back caching, however, delays the writing of modified data back to RAM. The reason for doing this is to reduce the number of times a frequently-modified piece of data must be written back to RAM.

Write-through cache is a bit simpler to implement; for this reason it is most common. Write-back cache is a bit trickier to implement; in addition to storing the actual data, it is necessary to maintain some sort of mechanism capable of flagging the cached data as clean (the data in cache is the same as the data in RAM), or dirty (the data in cache has been modified, meaning that the data in RAM is no longer current). It is also necessary to implement a way of periodically flushing dirty cache entries back to RAM.

4.2.3. Main Memory — RAM

RAM makes up the bulk of electronic storage on present-day computers. It is used as storage for both data and programs while those data and programs are in use. The speed of RAM in most systems today lies between the speed of cache memory and that of hard drives, and is much closer to the former than the latter.

The basic operation of RAM is actually quite straightforward. At the lowest level, there are the RAM chips — integrated circuits that do the actual "remembering." These chips have four types of connections to the outside world:

• Power connections (to operate the circuitry within the chip)

• Data connections (to enable the transfer of data into or out of the chip)

• Read/Write connections (to control whether data is to be stored into or retrieved from the chip)

• Address connections (to determine where in the chip the data should be read/written)

Here are the steps required to store data in RAM:

1. The data to be stored is presented to the data connections.

2. The address at which the data is to be stored is presented to the address connections.

3. The read/write connection to set to write mode.

Retrieving data is just as straightforward:

1. The address of the desired data is presented to the address connections.

2. The read/write connection is set to read mode.

3. The desired data is read from the data connections.

While these steps seem simple, they take place at very high speeds, with the time spent on each step measured in nanoseconds.

Nearly all RAM chips created today are sold as modules. Each module consists of a number of individual RAM chips attached to a small circuit board. The mechanical and electrical layout of the module adheres to various industry standards, making it possible to purchase memory from a variety of vendors.

Note

The main benefit to a system using industry-standard RAM modules is that it tends to keep the cost of RAM low, due to the ability to purchase the modules from more than just the system manufacturer. Although most computers use industry-standard RAM modules, there are exceptions. Most notable are laptops (and even here some standardization is starting to take hold) and high-end servers. However, even in these instances, it is likely that third-party RAM modules are available, assuming the system is relatively popular and is not a completely new design.

4.2.4. Hard Drives

All the technologies discussed so far are volatile in nature. In other words, data contained in volatile storage is lost when the power is turned off.

Hard drives, on the other hand, are non-volatile — the data they contain remains there, even after the power is removed. Because of this, hard drives occupy a special place in the storage spectrum. Their non-volatile nature makes them ideal for storing programs and data for longer-term use. Another unique aspect to hard drives is that, unlike RAM and cache memory, it is not possible to execute programs directly when they are stored on hard drives; instead, they must first be read into RAM.

Also different from cache and RAM is the speed of data storage and retrieval; hard drives are at least an order of magnitude slower than the all-electronic technologies used for cache and RAM. The difference in speed is due mainly to their electromechanical nature. There are four distinct phases taking place during each data transfer to or from a hard drive. The following list illustrates these phases, along with the time it would take a typical high-performance drive, on average, to complete each:

• Access arm movement (5.5 milliseconds)

• Disk rotation (.1 milliseconds)

• Heads reading/writing data (.00014 milliseconds)

• Data transfer to/from the drive's electronics (.003 Milliseconds)

Of these, only the last phase is not dependent on any mechanical operation.

	Note
	Although there is much more to learn about hard drives, disk storage technologies are discussed in more depth in Chapter 5 Managing Storage. For the time being, it is only necessary to keep in mind the huge speed difference between RAM and disk-based technologies and that their storage capacity usually exceeds that of RAM by a factor of at least 10, and often by 100 or more.

4.2.5. Off-Line Backup Storage

Off-line backup storage takes a step beyond hard drive storage in terms of capacity (higher) and speed (slower). Here, capacities are effectively limited only by your ability to procure and store the removable media.

The actual technologies used in these devices varies widely. Here are the more popular types:

• Magnetic tape

• Optical disk

Of course, having removable media means that access times become even longer, particularly when the desired data is on media not currently loaded in the storage device. This situation is alleviated somewhat by the use of robotic devices capable of automatically loading and unloading media, but the media storage capacities of such devices are still finite. Even in the best of cases, access times are measured in seconds, which is a far cry even from the relatively slow multi-millisecond access times typical for a high-performance hard drive.

Now that we have briefly studied the various storage technologies in use today, let us explore basic virtual memory concepts.